Adhesion railway

An adhesion railway relies on adhesion traction to move the train, and is the most widespread and common type of railway in the world.

Uses your system voice; voice and rate in settings.

≈ 7 min read

Cite, export and learn8 citation formats · 8 exports · lesson and quiz

Names in other languages

No names in other languages are held for this entry yet.

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

An adhesion railway relies on adhesion traction to move the train, and is the most widespread and common type of railway in the world. Adhesion traction is the frictional grip force between the locomotive's drive wheels and the steel rail.

Because the vast majority of railways are adhesion railways, the term adhesion railway is only used when it is necessary to distinguish adhesion railways from other types of railways with trains that are moved by other methods, such as by a stationary engine or motor pulling on a cable or chain attached to the carriages, or by a pinion gear meshing with a rack. The friction between the wheels and rails occurs in the wheel–rail interface, or contact patch.

The traction force, the braking forces and the centering forces all contribute to stable, smooth running. However, running friction increases costs, due to higher fuel and energy consumption and increased maintenance work needed to address fatigue damage and wear on rail heads and on the wheel rims, and rail movement from traction and braking forces.

F_\mathrm{max} = \mu W, where \mu is the coefficient of friction and W is the weight on the wheel. Usually the force needed to start sliding is greater than that needed to continue sliding. The former is concerned with static friction (also known as "stiction" ), or "limiting friction", whilst the latter is dynamic friction, also called "sliding friction".

For steel on steel, the coefficient of friction can be as high as 0.78, under laboratory conditions, but typically on railways it is between 0.35 and 0.5, whilst under extreme conditions it can fall to as low as 0.05. Thus a 100-tonne locomotive could have a tractive effort of 350 kilonewtons, under the ideal conditions (assuming sufficient force can be produced by the engine), falling to 50 kilonewtons under the worst conditions.

Steam locomotives suffer particularly badly from adhesion issues because the traction force at the wheel rim fluctuates (especially in two- or most four-cylinder engines) and, on large locomotives, not all wheels are driven. The "factor of adhesion", being the weight on the driven wheels divided by the theoretical starting tractive effort, was generally designed to have a value of 4 or slightly higher, reflecting a typical wheel–rail friction coefficient of 0.25.

A locomotive with a factor of adhesion much lower than 4 would be highly prone to wheelslip, although some three-cylinder locomotives, such as the SR V Schools class, operated with a factor of adhesion below 4 because the traction force at the wheel rim does not fluctuate as much. Other factors affecting the likelihood of wheelslip include wheel size, the sensitivity of the regulator and the skill of the driver. \lambda={2\pi}\sqrt{\frac{rd}{2k}}, where d is the wheel gauge, r is the nominal wheel radius and k is the taper of the treads.

For a given speed, the longer the wavelength and the lower the inertial forces will be, so the more likely it is that the oscillation will be damped out. Since the wavelength increases with reducing taper, increasing the critical speed requires the taper to be reduced, which implies a large minimum radius of turn.

A more complete analysis, taking account of the actual forces acting, yields the following result for the critical speed of a wheelset: V^2=\frac{Wrad^2}{k \left(4C+md^2 \right)}, where W is the axle load for the wheelset, a is a shape factor related to the amount of wear on the wheel and rail, C is the moment of inertia of the wheelset perpendicular to the axle, m is the wheelset mass. The result is consistent with the kinematic result in that the critical speed depends inversely on the taper.

It also implies that the weight of the rotating mass should be minimised compared with the weight of the vehicle. The wheel gauge appears in both the numerator and denominator, implying that it has only a second-order effect on the critical speed. The true situation is much more complicated, as the response of the vehicle suspension must be taken into account.

Restraining springs, opposing the yaw motion of the wheelset, and similar restraints on bogies, may be used to raise the critical speed further. However, in order to achieve the highest speeds without encountering instability, a significant reduction in wheel taper is necessary.

For example, taper on Shinkansen wheel treads was reduced to 1:40 (when the Shinkansen first ran) for both stability at high speeds and performance on curves. That said, from the 1980s onwards, the Shinkansen engineers developed an effective taper of 1:16 by tapering the wheel with multiple arcs, so that the wheel could work effectively both at high speed as well as at sharper curves.

Forces on wheels, creep

The behaviour of vehicles moving on adhesion railways is determined by the forces arising between two surfaces in contact. This may appear trivially simple from a superficial glance but it becomes extremely complex when studied to the depth necessary to predict useful results. The first error to address is the assumption that wheels are round.

A glance at the tyres of a parked car will immediately show that this is not true: the region in contact with the road is noticeably flattened, so that the wheel and road conform to each other over a region of contact. If this were not the case, the contact stress of a load being transferred through a line contact would be infinite.

Rails and railway wheels are much stiffer than pneumatic tyres and tarmac but the same distortion takes place at the region of contact. Typically, the area of contact is elliptical, of the order of 15 mm across. The distortion in the wheel and rail is small and localised but the forces which arise from it are large.

In addition to the distortion due to the weight, both wheel and rail distort when braking and accelerating forces are applied and when the vehicle is subjected to side forces. These tangential forces cause distortion in the region where they first come into contact, followed by a region of slippage.

The net result is that, during traction, the wheel does not advance as far as would be expected from rolling contact but, during braking, it advances further. This mix of elastic distortion and local slipping is known as "creep" (not to be confused with the creep of materials under constant load).

The definition of creep in this context is: \mbox{creep}=\frac{(\mbox{actual displacement} - \mbox{rolling displacement})}{(\mbox{rolling displacement})} \, In analysing the dynamics of wheelsets and complete rail vehicles, the contact forces can be treated as linearly dependent on the creep (Joost Jacques Kalker's linear theory, valid for small creepage), or more advanced theories can be used from frictional contact mechanics. The forces which result in directional stability, propulsion and braking may all be traced to creep.

It is present in a single wheelset and will accommodate the slight kinematic incompatibility introduced by coupling wheelsets together, without causing gross slippage, as was once feared. Provided the radius of turn is sufficiently great (as should be expected for express passenger services), two or three linked wheelsets should not present a problem.

However, 10 drive wheels (5 main wheelsets) are usually associated with heavy freight locomotives. \mbox{creep}=\frac{(\mbox{wheel speed} - \mbox{locomotive speed})}{(\mbox{locomotive speed})} \,

Text derived from https://en.wikipedia.org/w/index.php?oldid=1376833835 under CC BY-SA 4.0; modifications have been made.

Provenance

snapshot enwiki-001376833835 · captured 2026-09-26 · ledger · version history

Cite this page as: encyclopegia.org, “Adhesion railway”, snapshot enwiki-001376833835. https://encyclopegia.org/a/adhesion-railway

Sources cited in this revision

11 named source(s) extracted from the cited revision. A source with no author is shown by its publication; nothing is invented.