Anelasticity

Uses your system voice; voice and rate in settings.

Snapshot

≈ 9 min read

Names in other languages

No names in other languages are held for this entry yet.

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

Anelasticity is a property of materials that describes their behaviour when undergoing deformation. Its formal definition does not include the physical or atomistic mechanisms but still interprets the anelastic behaviour as a manifestation of internal relaxation processes. It is a behaviour differing (usually very slightly) from elastic behaviour.

Anelasticity is a property of materials that describes their behaviour when undergoing deformation. Its formal definition does not include the physical or atomistic mechanisms but still interprets the anelastic behaviour as a manifestation of internal relaxation processes. It is a behaviour differing (usually very slightly) from elastic behaviour. \sigma = M \epsilon \epsilon = J \sigma M = \frac{1}{J} The constant M is called the modulus of elasticity (or just modulus) while its reciprocal J is called the modulus of compliance (or just compliance).

There are three postulates that define the ideal elastic behaviour: (1) the strain response to each level of applied stress (or vice versa) has a unique equilibrium value; (2) the equilibrium response is achieved instantaneously; (3) the response is linear. These conditions may be lifted in various combinations to describe different types of behaviour, summarized in the following table: Anelasticity is therefore by the existence of a part of time dependent reaction, in addition to the elastic one in the material considered.

Background

It is also usually a very small fraction of the total response and so, in this sense, the usual meaning of "anelasticity" as "without elasticity" is improper in a physical sense. The formal definition of linearity is: "If a given stress history \sigma_1(t) produces the strain \epsilon_1(t) , and if a stress \sigma_2(t) gives rise to \epsilon_2(t) , then the stress \sigma_1(t) + \sigma_2(t) will give rise to the strain \epsilon_1(t) + \epsilon_2(t) ." The postulate of linearity is used because of its practical usefulness.

The theory would become much more complicated otherwise, but in cases of materials under low stress this postulate can be considered true. In general, the change of an external variable of a thermodynamic system causes a response from the system called thermal relaxation that leads it to a new equilibrium state. In the case of mechanical changes, the response is known as anelastic relaxation, and in the same formal way can be also described for example dielectric or magnetic relaxation.

The internal values are coupled to stress and strain through kinetic processes such as diffusion. So that the external manifestation of the internal relaxation behaviours is the stress strain relation, which in this case is time dependant. At equilibrium, M_\text{R} = 1/J_\text{R} , and at a short timescale, when the material behaves as if ideally elastic, M_\text{U} = 1/J_\text{U} also holds. The stress can be written as a complex number \sigma=\sigma_0 a^{i\omega t} where \sigma_0 is the amplitude and \omega the frequency of vibration.

Then the strain is periodic with the same frequency \epsilon=\epsilon_0 a^{i(\omega t-\phi)} where \epsilon_0 is the strain amplitude and \varphi is the angle by which the strain lags, called loss angle. For ideal elasticity \varphi = 0 . For the anelastic case \varphi is in general not zero, so the ratio \epsilon/\sigma is complex. This quantity is called the complex compliance J^\star(\omega) .

Thus, J^*(\omega)=\frac{\epsilon}{\sigma}=|J|(\omega)e^{-i\phi(\omega)} where |J|(\omega) , the absolute value of J^\star , is called the absolute dynamic compliance, given by \epsilon_0/\sigma_0 . This way two real dynamic response functions are defined, |J|(\omega) and \varphi(\omega) . Two other real response functions can also be introduced by writing the previous equation in another notation: J^*(\omega)=J_1(\omega)-iJ_2(\omega) where the real part is called "storage compliance" and the imaginary part is called "loss compliance".

J 1 and J 2 being called "storage compliance" and "loss compliance" respectively is significant, because calculating the energy stored and the energy dissipated in a cycle of vibration gives following equations: \Delta W =\oint \sigma d \epsilon = \pi J_2 \sigma_0^2 where \Delta W is the energy dissipated in a full cycle per unit of volume while the maximum stored energy W per unit volume is given by: W =\int_{\omega t =0}^{\pi /2} \sigma d \epsilon = \frac{1}{2} J_1 \sigma_0^2 The ratio of the energy dissipated to the maximum stored energy is called the "specific damping capacity”.

This ratio can be written as a function of the loss angle by \Delta W/W=2\pi\tan\phi . This shows that the loss angle \varphi gives a measure of the fraction of energy lost per cycle due to anelastic behaviour, and so it is known as the internal friction of the material. \frac{\omega_2-\omega_1}{\omega_\text{r}}=Q^{-1}=\phi The loss angle that measures the internal friction can be obtained directly from the plot, since it is the width of the resonance peak at half-maximum.

With this and the resonant frequency it is then possible to obtain the primary response functions. By changing the inertia of the sample the resonant frequency changes, and so can the response functions at different frequencies can be obtained. \delta=\ln\left(\frac{A_n}{A_{n+1}}\right) It is a convenient and direct way of measuring the damping, as it is directly related to the internal friction. The Boltzmann superposition principle states that every stress applied at a different time deforms the material as it if were the only one.

This can be written generally for a series of stresses \sigma_i(i=1,2,...,m) that are applied at successive times t_1',t_2',...,t_m' .

In this situation, the total strain will be: \epsilon(t)=\sum_{i=1}^m\sigma_iJ(t-t_i') or in the integral form, is the stress is varied continuously: \epsilon(t)=\int_{-\infin}^{t} J(t-t')\frac{d\sigma(t')}{dt'}dt' The controlled variable can always be changed, expressing the stress as a function of time in a similar way: \sigma(t)=\int_{-\infin}^{t} M(t-t')\frac{d\epsilon(t')}{dt'}dt' These integral expressions are a generalization of Hooke's law in the case of anelasticity, and they show that material acts almost as they have a memory of their history of stress and strain.

How it works

These two of equations imply that there is a relation between the J(t) and M(t). To obtain it the method of Laplace transforms can be used, or they can be related implicitly by: 1=M_UJ(t)+\int_{0}^{t} J(t-t'){d\sigma(t') \over dt'}dt' In this way though they are correlated in a complicated manner and it is not easy to evaluate one of these functions knowing the other.

Hover it is still possible in principle to derive the stress relaxation function from the creep function and vice versa thanks to the Boltzamann principle. a_0\sigma+a_1\dot{\sigma}+a_2\ddot{\sigma}+\cdot\cdot\cdot=b_0\epsilon+b_1\dot{\epsilon}+b_2\ddot{\epsilon}+\cdot\cdot\cdot For the specific case of anelasticity, which requires the existence of an equilibrium relation, additional restrictions must be placed on this equation. Each stress–strain equation can be accompanied by a mechanical model to help visualizing the behaviour of materials.

The Voigt model, described by the equation J\sigma=\epsilon+\tau\dot\epsilon , allows for no instantaneous deformation, therefore it is not a realistic representation of a crystalline solid. The generalized stress–strain equation for the Maxwell model is \tau\dot\sigma+\sigma=\tau M\dot\epsilon , and since it displays steady viscous creep rather than recoverable creep is yet again not suited to describe an anelastic material.

J_\text{R}\sigma+\tau_\sigma J_\text{U}\dot\sigma=\epsilon+\tau_\sigma \dot\epsilon The solid whose properties are defined by this equation is called the standard anelastic solid. The solution of this equation for the creep function is: J(t)=\frac{\epsilon(t)}{\sigma_0}=J_\text{R}-(J_\text{R}-J_\text{U})e^{-\frac{t}{\tau_\sigma}}=J_\text{U}+\delta (1-e^{-\frac{t}{\tau_\sigma}}) , where \tau_\sigma is called the relaxation time at constant stress.

To describe the stress relaxation behaviour, one can also consider another three-parameter model more suited to the stress relaxation experiment, consisting of a Maxwell unit placed in parallel with a spring. Its differential stress–strain equation is the same as the other model considered, therefore the two models are equivalent. The Voigt-type is more convenient in the analysis of creep, while the Maxwell-type for the stress relaxation.

J_1(\omega)=J_\text{U}+\frac{\delta J}{(1+\omega^2\tau_\sigma^2)} J_2(\omega)=\delta J\frac{\omega \tau_\sigma}{(1+\omega^2\tau_\sigma^2)} These are often called the Debye equations since were first derived by P. Debye for the case of dielectric relaxation phenomena.

The width of the peak at half maximum value for J_2 is given by \Delta(\log_{10}\omega\tau)=1.144 The equation for the internal friction \phi may also be expressed as a Debye peak, in the case where \delta J\ll J_\text{U} as: \phi \cong \Delta \frac{\omega\tau}{1+\omega^2\tau^2} The relaxation strength \Delta can be obtained from the height of such a peak, while the relaxation time \tau from the frequency at which the peak occurs. \tau^{-1}=v_0e^{-Q/kT} where T is the absolute temperature, v_o is a frequency factor, Q is the activation energy, k is the Boltzmann constant.

Therefore, where this equation applies, the quantity \tau may be varied over a wide range simply by changing the temperature. It then becomes possible to treat the dynamic response functions as functions of temperature.

Text derived from https://en.wikipedia.org/w/index.php?oldid=1336931555 under CC BY-SA 4.0; modifications have been made.

Provenance

snapshot enwiki-001336931555 · captured 1770384591.0 · version history

Cite this page as: encyclopegia.org, “Anelasticity”, snapshot enwiki-001336931555. https://encyclopegia.org/a/anelasticity

Sources cited in this revision

No external citation was extracted for this revision. That is a statement about the source, not a claim that none exists.