Audio power

Uses your system voice; voice and rate in settings.

Snapshot

≈ 10 min read

Names in other languages

No names in other languages are held for this entry yet.

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

Audio power is the electrical power transferred from an audio amplifier to a loudspeaker, measured in watts. The electrical power delivered to the loudspeaker, together with the speaker's efficiency, determines the sound power generated (with the rest of the electrical power being converted to heat). Amplifiers are limited in the electrical power they can output, while loudspeakers are limited in the electrical power they can convert to sound power without being damaged or distorting the audio signal. These limits, or power ratings, are important to consumers in finding compatible products and comparing competitors.

Audio power is the electrical power transferred from an audio amplifier to a loudspeaker, measured in watts. The electrical power delivered to the loudspeaker, together with the speaker's efficiency, determines the sound power generated (with the rest of the electrical power being converted to heat). Amplifiers are limited in the electrical power they can output, while loudspeakers are limited in the electrical power they can convert to sound power without being damaged or distorting the audio signal. These limits, or power ratings, are important to consumers in finding compatible products and comparing competitors.

Power handling

In audio electronics, there are several methods of measuring power output, for such things as amplifiers, and power handling capacity, for such things as loudspeakers. P_\mathrm{avg} = \frac{1}{T}\int_{0}^{T} v(t) \cdot i(t)\, dt \, For a purely resistive load, a simpler equation can be used, based on the root mean square (RMS) values of the voltage and current waveforms: P_\mathrm{avg} = V_\mathrm{rms} \cdot I_\mathrm{rms} \, In the case of a steady sinusoidal tone into a purely resistive load, this can be calculated from the peak amplitude of the voltage waveform (which is easier to measure with an oscilloscope) and the load's resistance: P_\mathrm{avg} = \frac{{V_\mathrm{rms}}^2}{R} = \frac{{V_\mathrm{peak}}^2}{2R} \, Though a speaker is not purely resistive and audio program is not a sinusoid, these equations are sometimes used to approximate power measurements for such a system. P_\mathrm{avg} = {(6~\mathrm{V})^2 \over 2(8~\Omega)}\,\ = 2.25~\mathrm{W} In most actual car systems, the amplifiers are connected in a bridge-tied load configuration, and speaker impedances are no higher than 4 Ω. High-power car amplifiers use a DC-to-DC converter to generate a higher supply voltage.

Continuous power and RMS power

Continuous average sine wave power ratings are a staple of performance specifications for audio amplifiers and, sometimes, loudspeakers. As described above, the term average power refers to the average value of the instantaneous power waveform over time. As this is typically derived from the root mean square (RMS) of the sine wave voltage, it may be referred to as RMS power or watts RMS. This should not to be interpreted as the RMS value of the power waveform. Watts RMS is used in an ANSI standard where it is also referred to as the nominal value and where there is a product mark requirement to use it. Continuous (as opposed to peak) implies that the device can function at this power level for long periods of time; that heat can be removed at the same rate it is generated, without temperature building up to the point of damage. On May 3, 1974, the Federal Trade Commission (FTC) instated its Amplifier Rule to combat the unrealistic power claims made by many hi-fi amplifier manufacturers. This rule prescribes continuous power measurements performed with sine wave signals for advertising and specifications of amplifiers sold in the US. This rule was amended in 1998 to cover self-powered speakers, such as those commonly used with personal computers. Typically, an amplifier's power specifications are calculated by measuring its RMS output voltage, with a continuous sine wave signal, at the onset of clipping—defined arbitrarily as a stated percentage of total harmonic distortion (THD), usually 1%, into specified load resistances. Typical loads used are 8 and 4 ohms per channel; many amplifiers used in professional audio are also specified at 2 ohms. Considerably more power can be delivered if distortion is allowed to increase; some manufacturers quote maximum power at a higher distortion, like 10%, making their equipment appear more powerful. The sine wave used for continuous power measurements does not actually describe the highly varied signals found in audio reproduction, but these measurements are widely regarded as a reasonable way of describing an amplifier's maximum output capability. In loudspeakers, thermal capacities of the voice coils and magnet structures largely determine continuous power handling ratings. However, at the lower end of a loudspeaker's usable frequency range, its power handling might necessarily be derated because of mechanical excursion limits. For example, a subwoofer rated at 100 watts may be able to handle 100 watts of power at 80 hertz, but at 25 hertz it might not be able to handle nearly as much power since such frequencies may force the driver beyond its mechanical limits much before reaching 100 watts from the amplifier.

Peak power

Peak power refers to the maximum of the instantaneous power waveform, which, for a sine wave, is always twice the average power. For other waveforms, the relationship between peak power and average power is the peak-to-average power ratio (PAPR). The peak power of an amplifier is determined by the voltage rails and the maximum amount of current its electronic components can handle instantaneously without damage. This characterizes the ability of equipment to handle quickly changing power levels, as many audio signals have a highly dynamic nature. Peak power is always a higher value than the average power figure, however, and so it has been tempting to use in advertising without context, making it look as though the amp has twice the power of competitors.

Total system power

Total system power is a term often used in audio electronics to rate the power of an audio system. Total system power refers to the total power consumption of the unit, rather than the power handling of the speakers or the power output of the amplifier. This can be viewed as a somewhat deceptive marketing ploy, as the total power consumption of the unit will, of course, be greater than any of its other power ratings, except for possibly the peak power of the amplifier. Shelf stereos and surround sound receivers are often rated using total system power. One way to use total system power to get a more accurate estimate of amplifier output power is to consider the amplifier class, from which one could derive an estimate of the power output by considering the efficiency of the class. For example, class AB amplifiers can vary widely from 25% to 75% efficiency while Class D amps are much higher at 80% to 95%. In some cases, an audio device may be measured by the total system power of all its loudspeakers by adding all their peak power ratings. Many home theater in a box systems are rated this way. Often, low-end home theater systems' power ratings are taken at a high level of harmonic distortion as well; as high as 10%, which would be noticeable.

Matching amplifier to loudspeaker

Charles "Chuck" McGregor, while serving as senior technologist for Eastern Acoustic Works, wrote a guideline for professional audio purchasers wishing to select properly sized amplifiers for their loudspeakers. Chuck McGregor recommended a rule of thumb in which the amplifier's maximum power output rating was twice the loudspeaker's continuous (so-called "RMS") rating, give or take 20%. In his example, a loudspeaker with a continuous power rating of 250 watts would be well-matched by an amplifier with a maximum power output within the range of 400 to 625 watts. JBL, which tests and labels their loudspeakers according to the IEC 268-5 standard (called IEC 60268-5 more recently) has a more nuanced set of recommendations, depending on the usage profile of the system, which more fundamentally involves the (worst case) crest factor of the signal used to drive the loudspeakers: For "carefully monitored applications where peak transient capability must be maintained, a system should be powered with an amplifier capable of delivering twice its IEC rating." As an example, a studio monitor rated at 300 watts IEC, can be safely driven by a 600-watt (RMS) amplifier, provided that "peak signals are normally of such short duration that they hardly stress the system's components". For "routine application where high continuous, but non-distorted, output is likely to be encountered, a system should be powered with an amplifier capable of delivering the IEC rating of the system". This includes most consumer systems. "Such systems can often be inadvertently overdriven, or can go into feedback. When powered with an amplifier equal to their IEC rating, the user is guaranteed of safe operation." "For musical instrument application, where distorted (overdriven) output may be a musical requirement, the system should be powered with an amplifier capable of delivering only one-half of the IEC rating for the system." This necessary because, for example, an amplifier normally outputting "300 watts of undistorted sinewave" can reach closer to 600 watts of power when clipping (i.e. when its output is closer to a square wave). If such a scenario is plausible, then for safe operation of the loudspeaker, the amplifier's (RMS) rating must no more than half the IEC power of the loudspeaker.

United States

Peak momentary power output and peak music power output are two different measurements with different specifications and should not be used interchangeably. Manufacturers who use different words such as pulse or performance may be reflecting their own non-standard system of measurement, with an unknown meaning. The Federal Trade Commission is putting an end to this with Federal Trade Commission (FTC) Rule 46 CFR 432 (1974), affecting Power Output Claims for Amplifiers Utilized in Home Entertainment Products. In response to a Federal Trade Commission order, the Consumer Electronics Association has established a clear and concise measure of audio power for consumer electronics. They have posted an FTC approved product marking template on their web site and the full standard is available for a fee. Many believe this will resolve much of the ambiguity and confusion in amplifier ratings. There will be ratings for speaker and powered speaker system too. This specification only applies to audio amplifiers. An EU counterpart is expected and all equipment sold in the US and Europe will be identically tested and rated. This regulation did not cover automobile entertainment systems, which consequently still suffer from power ratings confusion. However, a new Approved American National Standard ANSI/CEA-2006-B which includes testing & measurement methods for mobile audio amplifiers is being slowly phased into the market by many manufacturers.

Europe

DIN (Deutsches Institut für Normung, German Institute for Standardization) describes in DIN 45xxx several standards for measuring audio power. The DIN-standards (DIN-norms) are in common use in Europe.

International

IEC 60268-2 defines power amplifier specifications including power output.

Text derived from https://en.wikipedia.org/w/index.php?oldid=1376037114 under CC BY-SA 4.0; modifications have been made.

Sources cited in this revision

32 named source(s) extracted from the cited revision. A source with no author is shown by its publication; nothing is invented.