Bandwidth (signal processing)

bandwidth.

Uses your system voice; voice and rate in settings.

≈ 5 min read

Cite, export and learn8 citation formats · 8 exports · lesson and quiz

Names in other languages

No names in other languages are held for this entry yet.

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

bandwidth. Here the bandwidth equals the upper frequency. Bandwidth is the difference between the upper and lower frequencies in a continuous band of frequencies.

It is typically measured in unit of hertz (symbol Hz). It may refer more specifically to two subcategories: Passband bandwidth is the difference between the upper and lower cutoff frequencies of, for example, a band-pass filter, a communication channel, or a signal spectrum.

Baseband bandwidth is equal to the upper cutoff frequency of a low-pass filter or baseband signal, which includes a zero frequency. Bandwidth in hertz is a central concept in many fields, including electronics, information theory, digital communications, radio communications, signal processing, and spectroscopy and is one of the determinants of the capacity of a given communication channel.

A key characteristic of bandwidth is that any band of a given width can carry the same amount of information, regardless of where that band is located in the frequency spectrum. For example, a 3 kHz band can carry a telephone conversation whether that band is at baseband (as in a POTS telephone line) or modulated to some higher frequency.

However, wide bandwidths are easier to obtain and process at higher frequencies because the is smaller. The fact that in equivalent baseband models of communication systems, the signal spectrum consists of both negative and positive frequencies, can lead to confusion about bandwidth since they are sometimes referred to only by the positive half, and one will occasionally see expressions such as B = 2W , where B is the total bandwidth (i.e. the maximum passband bandwidth of the carrier-modulated RF signal and the minimum passband bandwidth of the physical passband channel), and W is the positive bandwidth (the baseband bandwidth of the equivalent channel model).

For instance, the baseband model of the signal would require a low-pass filter with cutoff frequency of at least W to stay intact, and the physical passband channel would require a passband filter of at least B to stay intact. B = \Delta f = f_\mathrm H - f_\mathrm L where f_\mathrm H and f_\mathrm L are the upper and lower frequency limits respectively of the band in question.

B_\mathrm F = \frac {\Delta f}{f_\mathrm C} \, . The center frequency is usually defined as the arithmetic mean of the upper and lower frequencies so that, f_\mathrm C = \frac {f_\mathrm H + f_\mathrm L}{2} \ and B_\mathrm F = \frac {2 (f_\mathrm H - f_\mathrm L)}{f_\mathrm H + f_\mathrm L} \, .

However, the center frequency is sometimes defined as the geometric mean of the upper and lower frequencies, f_\mathrm C = \sqrt {f_\mathrm H f_\mathrm L} and B_\mathrm F = \frac {f_\mathrm H - f_\mathrm L}{\sqrt {f_\mathrm H f_\mathrm L}} \, . While the geometric mean is more rarely used than the arithmetic mean (and the latter can be assumed if not stated explicitly) the former is considered more mathematically rigorous.

It more properly reflects the logarithmic relationship of fractional bandwidth with increasing frequency. For narrowband applications, there is only marginal difference between the two definitions. The geometric mean version is inconsequentially larger.

For wideband applications they diverge substantially with the arithmetic mean version approaching 2 in the limit and the geometric mean version approaching infinity. Fractional bandwidth is sometimes expressed as a percentage of the center frequency (percent bandwidth, \%B ), \%B_\mathrm F = 100 \frac {\Delta f}{f_\mathrm C} \, . B_\mathrm R= \frac {f_\mathrm H}{f_\mathrm L} \, .

Ratio bandwidth may be notated as B_\mathrm R:1 . The relationship between ratio bandwidth and fractional bandwidth is given by, B_\mathrm F = 2 \frac {B_\mathrm R - 1}{B_\mathrm R + 1} and B_\mathrm R = \frac {2 + B_\mathrm F}{2 - B_\mathrm F} \, . Percent bandwidth is a less meaningful measure in wideband applications.

A percent bandwidth of 100% corresponds to a ratio bandwidth of 3:1. All higher ratios up to infinity are compressed into the range 100–200%. Ratio bandwidth is often expressed in octaves (i.e., as a frequency level) for wideband applications.

An octave is a frequency ratio of 2:1 leading to this expression for the number of octaves, \log_2 \left(B_\mathrm R\right) . B_n = \frac{\int_{-\infty}^{\infty} |H(f)|^2 \, df}{2|H(0)|^2} = \frac{\int_{-\infty}^{\infty} |h(t)|^2 \, dt}{2\left|\int_{-\infty}^{\infty} h(t) \, dt\right|^2} \, .

The same expression can be applied to bandpass systems by substituting the equivalent baseband frequency response for H(f) . The noise equivalent bandwidth is widely used to simplify the analysis of telecommunication systems in the presence of noise.

Text derived from https://en.wikipedia.org/w/index.php?oldid=1377743758 under CC BY-SA 4.0; modifications have been made.

Provenance

snapshot enwiki-001377743758 · captured 2026-09-30 · ledger · version history

Cite this page as: encyclopegia.org, “Bandwidth (signal processing)”, snapshot enwiki-001377743758. https://encyclopegia.org/a/bandwidth-signal-processing

Sources cited in this revision

2 named source(s) extracted from the cited revision. A source with no author is shown by its publication; nothing is invented.