Beachcat

Uses your system voice; voice and rate in settings.

Snapshot

≈ 7 min read

Names in other languages

No names in other languages are held for this entry yet.

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

The term beachcat is an informal name for one of the most common types of small recreational sailboats, minimalist 14 to 20 foot catamarans, almost always with a cloth "trampoline" stretched between the two hulls, typically made of fiberglass or more recently rotomolded plastic. The name comes from the fact that they are designed to be sailed directly off a sand beach, unlike most other small boats which are launched from a ramp. The average 8 foot width of the beachcat means it can also sit upright on the sand and is quite stable in this position, unlike a monohull of the same size. The Hobie 14 and Hobie 16 are two of the earliest boats of this type that achieved widespread popularity, and popularized the term as well as created the template for this type of boat.

The term beachcat is an informal name for one of the most common types of small recreational sailboats, minimalist 14 to 20 foot catamarans, almost always with a cloth "trampoline" stretched between the two hulls, typically made of fiberglass or more recently rotomolded plastic. The name comes from the fact that they are designed to be sailed directly off a sand beach, unlike most other small boats which are launched from a ramp. The average 8 foot width of the beachcat means it can also sit upright on the sand and is quite stable in this position, unlike a monohull of the same size. The Hobie 14 and Hobie 16 are two of the earliest boats of this type that achieved widespread popularity, and popularized the term as well as created the template for this type of boat.

Basic proportions

Catamarans use their wide form to get stability while keeping wetted area low with just 2 narrow hulls in the water. As the windspeed increases, the sailor(s) usually can 'trapeze' off the side using their weight to minimize the boats heeling and enabling higher boat speed. Beach cats range in length from about up to (Stiletto). The smaller boats are often intended to sail and race with one sailor aboard, those boats usually have no jib sail and are often long and about . The width of the boat (the beam) is ideally a bit more than 1/2 the hull length, i.e. the Supercat had a beam and is one of the very highest performing catamarans, however a 12 foot wide boat needs to be completely disassembled for transport by trailer on public roads, that greatly limited sales and popularity of the Supercat 20, as well as the Tornado with its beam. Most Beachcats were limited to a maximum beam but in a peculiar twist of fate, in the US when the trucking union requested permission to drive faster on highways than the then limit, the Federal government instead raised the maximum trailerable width to 8'6", enabling all trailerable boats to be designed 6 inches wider. Boats from the mid-1980s were often then built to the new width, most older designs were not updated however as they were considered 'one designs' and remained unchanged. The mid size beachcats intended for two persons or more will usually weigh about (typical 18 foot). Handling beachcats on the beach is commonly aided using 'beach wheels', essentially an aluminum pole as an axle with two large lightweight tires that do not sink into the sand enabling the boat to be rolled about by one or two persons.

Pacific

One early beachcat, the Pacific cat, appeared in 1960 in California. The Pacific cat was designed by Carter Pyle and was first built in 1960. It was slightly smaller than , and was a solid fiberglass catamaran with a solid core deck and traditional catamaran sail plan. The design's chief limitation was its weight of over with approximately of sail area. The design was a traditional design with dagger boards and a hard deck. By comparison, the Aqua Cat 12 weighed and could easily be carried by two people, and the mast raised by one person. Photos of the Pacific cat demonstrate that it was adept at handling the daunting Pacific coast surf, probably due to the momentum it carried even with the limited (for the time) sail plan. Pacific cats were made by Newport Boats / Mobjack Manufacturing.

Aqua

In the United States, Art Javes designed and marketed an early fiberglass catamaran sailboat, the Aqua, in 1961. The Aqua was a 12-foot-long fiberglass hulled cat, which featured two flat-bottomed, foam filled, symmetric fiberglass hulls. These hulls were connected with aluminum tubing that supported a trampoline-style deck that was large enough for several people. It also featured an unusual "lateen rigged" sail that was supported by a rigid aluminum A-frame. The mast itself was topped with a Styrofoam float that helped insure that a capsizing, (especially in shallow water that could damage the mast), would be easily righted and result only in the boat going part way over. If capsized it was designed to rest on one hull, with the ball at the top of the mast preventing it from going fully inverted. The flat bottomed hulls made it a beach-friendly catamaran, but its reliance on dagger boards meant it had a draft of 2 ft with the dagger boards in position. Art Javes partnered with Billy Mills to produce about 1,000 boats a year for a 10-year run. The Aqua was made by American Fiberglass Corp from 1962 to 1972. Originally based in Norwalk, Connecticut, the company was in the sailboat division of General Recreation Corp in Charleston, SC as of 1970. Around 1976, an employee purchased the Aqua product line and it is still available from American Sail, Inc. in Charleston, South Carolina. With more than 30,000 boats shipped, the Aqua was inducted into the National Sailing Hall of Fame in 2001, and is still in production today. The original Aqua cat 12 was modified to an improved Aqua Cat 12.5 and is also available as an Aqua Cat 14 Catamaran which features upturned hulls and is available in an easier sailing resort model. The model uses small keels to replace the dagger boards found on the smaller Aqua cats. There was also an 18ft prototype that featured cushioned 6ft long seats located above the hulls.

Prindle

The Prindle Cat, introduced in 1972, sought to improve on the basic Hobie design by increasing the forward buoyancy with an almost vertical sheer (a trend that is currently the vogue in forward design, see, the 2011 Hobie "Wild Cat" F18 design and most of the current cruising designs from Fountaine Pajot, Dolphin, Privilege and Lagoon). The Prindle Cats, initially 16- and 18-ft designs, were comparable to the Hobies but were remarkable for their resistance to "pearling" (in surfer parlance) or "pitch poling" (in sailing vernacular). Even a well-sailed Hobie 16 was (and still is) quite capable of burying a hull and pitching end-over-end. The Prindles, with more forward buoyancy, resist this tendency, allowing more forward weight balance in heavier air (wind speed), although Prindles are still capable of pitch-poling given the right combination of forward weight, wind and sea conditions. Although out of production, the Prindle 16 is still in good supply on the used market, but the asymmetrical hulled 18s are rare. Prindle moved into the classes production in the early 1990s, with the development of the Prindle 19, a well designed, fast and balanced ship. The Prindle 19 class continues to grow but is at best a borderline "beach cat", with more of an emphasis on hydrodynamically linear hull design and the use of dagger boards.

See also

List of multihulls Turtling

References

Text derived from https://en.wikipedia.org/w/index.php?oldid=1352068527 under CC BY-SA 4.0; modifications have been made.

Sources cited in this revision

4 named source(s) extracted from the cited revision. A source with no author is shown by its publication; nothing is invented.