beam diameter

Uses your system voice; voice and rate in settings.

Q4876179Snapshot

≈ 11 min read

Names in other languages

  • Françaislargeur de faisceau
  • caDiàmetre del feix
  • DeutschStrahldurchmesser
  • Bahasa Indonesiadiameter pancaran
  • Englishbeam diameter
  • Русскийдиаметр луча
  • 日本語ビーム幅
  • 中文束直徑

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

showing beamwidth The beam diameter or beam width of an electromagnetic beam is the diameter along any specified line that is perpendicular to the beam axis and intersects it. Since beams typically do not have sharp edges, the diameter can be defined in many different ways. Five definitions of the beam width are in common use: D4σ, 10/90 or 20/80 knife-edge, 1/e 2 , FWHM, and D86. The beam width can be measured in units of length at a particular plane perpendicular to the beam axis, but it can also refer to the angular diameter (i.e., angular width), which is the angle subtended by the beam at the source. The angular width is also called the beam divergence. Beam diameter is usually used to characterize electromagnetic beams in the optical regime, and occasionally in the microwave regime, that is, cases in which the aperture from which the beam emerges is very large with respect to the wavelength. Beam diameter usually refers to a beam of circular cross section, but not necessarily so. A beam may, for example, have an elliptical cross section, in which case the orientation of the beam diameter must be specified, for example with respect to the major or minor axis of the elliptical cross section. The term "beam width" may be preferred in applications where the beam does not have circular symmetry.

showing beamwidth The beam diameter or beam width of an electromagnetic beam is the diameter along any specified line that is perpendicular to the beam axis and intersects it. Since beams typically do not have sharp edges, the diameter can be defined in many different ways. Five definitions of the beam width are in common use: D4σ, 10/90 or 20/80 knife-edge, 1/e 2 , FWHM, and D86. The beam width can be measured in units of length at a particular plane perpendicular to the beam axis, but it can also refer to the angular diameter (i.e., angular width), which is the angle subtended by the beam at the source. The angular width is also called the beam divergence. Beam diameter is usually used to characterize electromagnetic beams in the optical regime, and occasionally in the microwave regime, that is, cases in which the aperture from which the beam emerges is very large with respect to the wavelength. Beam diameter usually refers to a beam of circular cross section, but not necessarily so. A beam may, for example, have an elliptical cross section, in which case the orientation of the beam diameter must be specified, for example with respect to the major or minor axis of the elliptical cross section. The term "beam width" may be preferred in applications where the beam does not have circular symmetry.

Definitions

Siegman lists seven different measures of beam width, with some of the practical difficulties of defining beam width. Commonly used definitions include:

Rayleigh beamwidth

The angle between the maximum peak of radiated power and the first null (no power radiated in this direction) is called the Rayleigh beamwidth. This is well-defined for some beam profiles, for example, the Airy diffraction pattern of a uniformly-lit aperture, but is undefined for an ideal Gaussian beam.

Full width at half maximum

The half-power beamwidth is the angle off boresight at which the antenna gain first falls to half power (approximately ) from the peak. The simplest way to define the width of a beam is to choose two diametrically opposite points at which the irradiance is a specified fraction of the beam's peak irradiance, and take the distance between them as a measure of the beam's width. An obvious choice for this fraction is (−3 dB), in which case the diameter obtained is the full width at half maximum (FWHM). Beamwidth is usually but not always expressed in degrees and for the horizontal plane. It refers to the main lobe, when referenced to the peak effective radiated power of the main lobe. In lighting applications, beam angle is often defined as FWHM luminous intensity. The field angle for floodlights is the full width at 10% intensity.

For antenna arrays

The beamwidth can be computed for arbitrary antenna arrays. Defining the array manifold as the complex response of the \mathrm{m} element antenna array as where \mathrm{A}(\theta) is a matrix with \mathrm{m} rows, the beam pattern is first computed as: \mathrm{B}(\theta) = \frac{1}{\mathrm{m}}\mathrm{A}(\theta_0)^{*}\mathrm{A}(\theta) where \mathrm{A}(\theta_0)^{*} is the conjugate transpose of \mathrm{A} at the reference angle From the beam pattern the antenna power is computed as: \mathrm{P} = |\mathrm{B}|^{2}\,. The half-power beamwidth (HPBW) is then found as the value of \theta where {{nowrap| \mathrm{P} = 0.5\mathrm{P_{max}} .}} The 1/e 2 width is the distance between the two points where the intensity falls to 1/e 2 = 0.135 times the maximum value. If there are more than two points that are 1/e 2 times the maximum value, then the two points closest to the maximum are chosen. The 1/e 2 width is important in the mathematics of Gaussian beams, in which the intensity profile is described by I(r) = I_{0} \left( \frac{w_0}{w} \right)^2 \exp \! \left( \! -2 \frac{r^2}{w^2}\right ). The American National Standard Z136.1-2007 for Safe Use of Lasers (p. 6) defines the beam diameter as the distance between diametrically opposed points in that cross-section of a beam where the power per unit area is 1/e (0.368) times that of the peak power per unit area. This is the beam diameter definition that is used for computing the maximum permissible exposure to a laser beam. The Federal Aviation Administration also uses the 1/e definition for laser safety calculations in FAA Order JO 7400.2, Para. 29-1-5d. Measurements of the 1/e 2 width only depend on three points on the marginal distribution, unlike D4σ and knife-edge widths that depend on the integral of the marginal distribution. 1/e 2 width measurements are noisier than D4σ width measurements. For multimodal marginal distributions (a beam profile with multiple peaks), the 1/e 2 width usually does not yield a meaningful value and can grossly underestimate the inherent width of the beam. For multimodal distributions, the D4σ width is a better choice. For an ideal single-mode Gaussian beam, the D4σ, D86 and 1/e 2 width measurements would give the same value. For a Gaussian beam, the relationship between the 1/e 2 width and the full width at half maximum is 2w = \frac{\sqrt 2\ \mathrm{FWHM}}{\sqrt{\ln 2}} \simeq 1.699 \times \mathrm{FWHM}, where 2w is the full width of the beam at 1/e 2 . Looking at the intensity profile of a Gaussian beam, the 1/e 2 width can also be related to its standard deviation: w = 2 \sigma . D4\sigma = 4 \sigma = 4 \sqrt{\frac{\int_{-\infty}^\infty \int_{-\infty}^\infty I(x,y) (x - \bar{x})^2 \,dx \,dy} {\int_{-\infty}^\infty \int_{-\infty}^\infty I(x,y)\, dx \,dy}}, where \bar{x} = \frac{\int_{-\infty}^\infty \int_{-\infty}^\infty I(x,y) x \,dx \,dy}{\int_{-\infty}^\infty \int_{-\infty}^\infty I(x,y) \,dx \,dy} is the centroid of the beam profile in the x direction. When a beam is measured with a laser beam profiler, the wings of the beam profile influence the D4σ value more than the center of the profile, since the wings are weighted by the square of its distance, x 2 , from the center of the beam. If the beam does not fill more than a third of the beam profiler's sensor area, then there will be a significant number of pixels at the edges of the sensor that register a small baseline value (the background value). If the baseline value is large or if it is not subtracted out of the image, then the computed D4σ value will be larger than the actual value because the baseline value near the edges of the sensor are weighted in the D4σ integral by x 2 . Therefore, baseline subtraction is necessary for accurate D4σ measurements. The baseline is easily measured by recording the average value for each pixel when the sensor is not illuminated. The D4σ width, unlike the FWHM and 1/e 2 widths, is meaningful for multimodal marginal distributions — that is, beam profiles with multiple peaks — but requires careful subtraction of the baseline for accurate results. The D4σ is the ISO international standard definition for beam width. d_{\sigma x} = 2 \sqrt{2} \left( \langle x^2 \rangle + \langle y^2 \rangle + \gamma \left( \left( \langle x^2 \rangle - \langle y^2 \rangle \right)^2 + 4 \langle xy \rangle^2 \right)^{1/2} \right)^{1/2} and d_{\sigma y} = 2 \sqrt{2} \left( \langle x^2 \rangle + \langle y^2 \rangle - \gamma \left( \left( \langle x^2 \rangle - \langle y^2 \rangle \right)^2 + 4 \langle xy \rangle^2 \right)^{1/2} \right)^{1/2}. This definition also incorporates information about x–y correlation \langle xy \rangle , but for circular symmetric beams, both definitions are the same. Some new symbols appeared within the formulas, which are the first- and second-order moments: \langle x \rangle = \frac{1}{P} \int I(x,y) x \,dx \,dy, \langle y \rangle = \frac{1}{P} \int I(x,y) y \,dx \,dy, \langle x^2 \rangle = \frac{1}{P} \int I(x,y) (x - \langle x \rangle )^2 \,dx \,dy, \langle xy \rangle = \frac{1}{P} \int I(x,y) (x - \langle x \rangle ) (y - \langle y \rangle ) \,dx \,dy, \langle y^2 \rangle = \frac{1}{P} \int I(x,y) (y - \langle y \rangle )^2 \,dx \,dy, the beam power P = \int I(x,y) \,dx \,dy, and \gamma = \sgn \left( \langle x^2 \rangle - \langle y^2 \rangle \right) = \frac{\langle x^2 \rangle - \langle y^2 \rangle} . Using this general definition, also the beam azimuthal angle \phi can be expressed. It is the angle between the beam directions of minimal and maximal elongations, known as principal axes, and the laboratory system, being the x and y axes of the detector and given by \phi = \frac{1}{2} \arctan \frac{2 \langle xy \rangle}{\langle x^2 \rangle - \langle y^2 \rangle }.

Measurement

International standard ISO 11146-1:2005 specifies methods for measuring beam widths (diameters), divergence angles and beam propagation ratios of laser beams (if the beam is stigmatic) and for general astigmatic beams ISO 11146-2 is applicable. The D4σ beam width is the ISO standard definition and the measurement of the M 2 beam quality parameter requires the measurement of the D4σ widths. The other definitions provide complementary information to the D4σ. The D4σ and knife-edge widths are sensitive to the baseline value, whereas the 1/e 2 and FWHM widths are not. The fraction of total beam power encompassed by the beam width depends on which definition is used. The width of laser beams can be measured by capturing an image on a camera, or by using a laser beam profiler.

See also

Beam waist Fresnel zone

References

Text derived from https://en.wikipedia.org/w/index.php?oldid=1351910430 under CC BY-SA 4.0; modifications have been made.

Provenance

snapshot beam-diameter-556571-efb77d4e8c157fb5 · hash efb77d4e8c157fb55708813714282083449864048ee55bc18fbd2a13d1546295 · captured 1777578775.0 · version history

Cite this page as: encyclopegia.org, “beam diameter”, snapshot beam-diameter-556571-efb77d4e8c157fb5. https://encyclopegia.org/a/beam-diameter

Sources cited in this revision

No external citation was extracted for this revision. That is a statement about the source, not a claim that none exists.