Bearing capacity

In geotechnical engineering, bearing capacity is the capacity of soil to support the loads applied to the ground.

Uses your system voice; voice and rate in settings.

≈ 5 min read

Cite, export and learn8 citation formats · 8 exports · lesson and quiz

Names in other languages

No names in other languages are held for this entry yet.

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

In geotechnical engineering, bearing capacity is the capacity of soil to support the loads applied to the ground. The bearing capacity of soil is the maximum average contact pressure between the foundation and the soil which should not produce shear failure in the soil.

Ultimate bearing capacity is the theoretical maximum pressure which can be supported without failure; allowable bearing capacity is the ultimate bearing capacity divided by a factor of safety. Sometimes, on soft soil sites, large settlements may occur under loaded foundations without actual shear failure occurring; in such cases, the allowable bearing capacity is based on the maximum allowable settlement.

The allowable bearing pressure is the maximum pressure that can be applied to the soil without causing failure. The ultimate bearing capacity, on the other hand, is the maximum pressure that can be applied to the soil before it fails. There are three modes of failure that limit bearing capacity: general shear failure, local shear failure, and punching shear failure.

It depends upon the shear strength of soil as well as shape, size, depth and type of foundation. q_{ult} = 1.3 c' N_c + \sigma '_{zD} N_q + 0.4 \gamma ' B N_\gamma \ For continuous foundations: q_{ult} = c' N_c + \sigma '_{zD} N_q + 0.5 \gamma ' B N_\gamma \ For circular foundations: q_{ult} = 1.3 c' N_c + \sigma '_{zD} N_q + 0.3 \gamma ' B N_\gamma \ where N_q = \frac{ e ^{ 2 \pi \left( 0.75 - \phi '/360 \right) \tan \phi ' } }{2 \cos ^2 \left( 45 + \phi '/2 \right) } N_c = 5.14 \ for φ' = 0 [Note: 5.14 is Meyerhof's value -- see below. Terzaghi's value is 5.7.]

N_c = \frac{ N_q - 1 }{ \tan \phi '} for φ' > 0 [Note: As phi' goes to zero, N_c goes to 5.71...] N_\gamma = \frac{ \tan \phi ' }{2} \left( \frac{ K_{p \gamma} }{ \cos ^2 \phi ' } - 1 \right) c′ is the effective cohesion. σ zD ′ is the vertical effective stress at the depth the foundation is laid. γ′ is the effective unit weight when saturated or the total unit weight when not fully saturated.

B is the width or the diameter of the foundation. φ′ is the effective internal angle of friction. K pγ is obtained graphically. Simplifications have been made to eliminate the need for K pγ .

One such was done by Coduto, given below, and it is accurate to within 10%. N_\gamma = \frac{ 2 \left( N_q + 1 \right) \tan \phi ' }{1 + 0.4 \sin 4 \phi ' } For foundations that exhibit the local shear failure mode in soils, Terzaghi suggested the following modifications to the previous equations. The equations are given below.

For square foundations: q_{ult} = 0.867 c' N '_c + \sigma '_{zD} N '_q + 0.4 \gamma ' B N '_\gamma \ For continuous foundations: q_{ult} = \frac{2}{3} c' N '_c + \sigma '_{zD} N '_q + 0.5 \gamma ' B N '_\gamma \ For circular foundations: q_{ult} = 0.867 c' N '_c + \sigma '_{zD} N '_q + 0.3 \gamma ' B N '_\gamma \ N '_c, N '_q and N '_y , the modified bearing capacity factors, can be calculated by using the bearing capacity factors equations(for N_c, N_q, and N_y , respectively) by replacing the effective internal angle of friction (\phi ') by a value equal to : tan^{-1}\, (\frac{2}{3} tan \phi ') In 1951, Meyerhof published a bearing capacity theory which could be applied to rough shallow and deep foundations. Meyerhof (1951, 1963) proposed a bearing-capacity equation similar to that of Terzaghi's but included a shape factor s-q with the depth term Nq.

He also included depth factors and inclination factors. [Note: Meyerhof re-evaluated N_q based on a different assumption from Terzaghi and found N_q = ( 1 + sin phi) exp (pi tan phi ) / (1 - sin phi). Then N_c is the same equation as Terzaghi: N_c = (N_q - 1) / tan phi.

For phi = 0, Meyerhof's N_c converges to 2 + pi = 5.14.... Meyerhof also re-evaluated N_gamma and obtained N_gamma = (N_q - 1) tan(1.4 phi).] q_{all} = \frac{q_{ult}}{FS}

See also

Soil mechanics Bearing capacity of Soil

Text derived from https://en.wikipedia.org/w/index.php?oldid=1314174607 under CC BY-SA 4.0; modifications have been made.

Provenance

snapshot enwiki-001314174607 · captured 2025-09-30 · ledger · version history

Cite this page as: encyclopegia.org, “Bearing capacity”, snapshot enwiki-001314174607. https://encyclopegia.org/a/bearing-capacity

Sources cited in this revision

2 named source(s) extracted from the cited revision. A source with no author is shown by its publication; nothing is invented.