Bit rate

Uses your system voice; voice and rate in settings.

Snapshot

≈ 9 min read

Names in other languages

No names in other languages are held for this entry yet.

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

In telecommunications and computing, bit rate (bitrate or as a variable R) is the number of bits that are conveyed or processed per unit of time. The bit rate is expressed as bits per second (symbol: bit/s), often with an SI prefix such as kilo (1 kbit/s = 1,000 bit/s), mega (1 Mbit/s = 1,000 kbit/s), giga (1 Gbit/s = 1,000 Mbit/s) or tera (1 Tbit/s = 1,000 Gbit/s). The non-standard abbreviation bps is often used: 1 Mbps is 1 Mbit/s, that is, one million bits per second.

The bit rate is different from the transfer rate, measured in transfers per second, when the channel is parallel and thus transfers multiple bits per transfer. In most computing and digital communication environments, one byte per second (symbol: B/s) corresponds to 8 bit/s ( ).

However if stop bits, start bits, and parity bits need to be factored in, a higher number of bits per second will be required to achieve a throughput of the same number of bytes.

In telecommunications and computing, bit rate (bitrate or as a variable R) is the number of bits that are conveyed or processed per unit of time. The bit rate is expressed as bits per second (symbol: bit/s), often with an SI prefix such as kilo (1 kbit/s = 1,000 bit/s), mega (1 Mbit/s = 1,000 kbit/s), giga (1 Gbit/s = 1,000 Mbit/s) or tera (1 Tbit/s = 1,000 Gbit/s). The non-standard abbreviation bps is often used: 1 Mbps is 1 Mbit/s, that is, one million bits per second.

The bit rate is different from the transfer rate, measured in transfers per second, when the channel is parallel and thus transfers multiple bits per transfer. In most computing and digital communication environments, one byte per second (symbol: B/s) corresponds to 8 bit/s ( ).

However if stop bits, start bits, and parity bits need to be factored in, a higher number of bits per second will be required to achieve a throughput of the same number of bytes. The binary prefixes defined by International Standard IEC 80000-13 are sometimes used: e.g., 1 KiB/s = 1024 B/s = 8192 bit/s, and 1 MiB/s = 1024 KiB/s.

Gross bit rate

In digital communication systems, the physical layer gross bitrate, raw bitrate, data signaling rate, gross data transfer rate or uncoded transmission rate (sometimes written as a variable R b or f b ) is the total number of physically transferred bits per second over a communication link, including useful data as well as protocol overhead. In case of serial communications, the gross bit rate is related to the bit transmission time T_\text{b} as: R_\text{b} = {1 \over T_\text{b}}, The gross bit rate is related to the symbol rate or modulation rate, which is expressed in baud or symbols per second.

However, the gross bit rate and the baud value are equal only when there are only two levels per symbol, representing 0 and 1, meaning that each symbol of a data transmission system carries exactly one bit of data; this is not the case for modern modulation systems used in modems and LAN equipment. For most line codes and modulation methods: \text{symbol rate} \leq \text{gross bit rate} More specifically, a line code (or baseband transmission scheme) representing the data using pulse-amplitude modulation with 2^N different voltage levels, can transfer N bits per pulse.

A digital modulation method (or passband transmission scheme) using 2^N different symbols, for example 2^N amplitudes, phases or frequencies, can transfer N bits per symbol. This results in: \text{gross bit rate} = \text{symbol rate} \times N An exception from the above is some self-synchronizing line codes, for example Manchester coding and return-to-zero (RTZ) coding, where each bit is represented by two pulses (signal states), resulting in: \text{gross bit rate = symbol rate/2} A theoretical upper bound for the symbol rate in baud, symbols/s or pulses/s for a certain spectral bandwidth in hertz is given by the Nyquist law: \text{symbol rate} \leq \text{Nyquist rate} = 2 \times \text{bandwidth} In practice this upper bound can only be approached for line coding schemes and for so-called vestigial sideband digital modulation.

Most other digital carrier-modulated schemes, for example ASK, PSK, QAM and OFDM, can be characterized as double sideband modulation, resulting in the following relation: \text{symbol rate} \leq \text{bandwidth} In case of parallel communication, the gross bit rate is given by \sum_{i = 1}^{n} \frac{\log_2 {M_i} }{T_i} where n is the number of parallel channels, M i is the number of symbols or levels of the modulation in the ith channel, and T i is the symbol duration time, expressed in seconds, for the ith channel. The net bit rate of ISDN2 Basic Rate Interface (2 B-channels + 1 D-channel) of 64+64+16 = 144 kbit/s also refers to the payload data rates, while the D channel signalling rate is 16 kbit/s. The net bit rate of the Ethernet 100BASE-TX physical layer standard is 100 Mbit/s, while the gross bitrate is 125 Mbit/s, due to the 4B5B (four bit over five bit) encoding.

In this case, the gross bit rate is equal to the symbol rate or pulse rate of 125 megabaud, due to the NRZI line code. In communications technologies without forward error correction and other physical layer protocol overhead, there is no distinction between gross bit rate and physical layer net bit rate.

For example, the net as well as gross bit rate of Ethernet 10BASE-T is 10 Mbit/s. Due to the Manchester line code, each bit is represented by two pulses, resulting in a pulse rate of 20 megabaud. The "connection speed" of a V.92 voiceband modem typically refers to the gross bit rate, since there is no additional error-correction code.

It can be up to 56,000 bit/s downstream and 48,000 bit/s upstream. A lower bit rate may be chosen during the connection establishment phase due to adaptive modulation slower but more robust modulation schemes are chosen in case of poor signal-to-noise ratio. Due to data compression, the actual data transmission rate or throughput (see below) may be higher.

The channel capacity, also known as the Shannon capacity, is a theoretical upper bound for the maximum net bitrate, exclusive of forward error correction coding, that is possible without bit errors for a certain physical analog node-to-node communication link. net bit rate ≤ channel capacity The channel capacity is proportional to the analog bandwidth in hertz. This proportionality is called Hartley's law.

Consequently, the net bit rate is sometimes called digital bandwidth capacity in bit/s.

Multimedia

In digital multimedia, bit rate represents the amount of information, or detail, that is stored per unit of time of a recording. The bitrate depends on several factors: The original material may be sampled at different frequencies. The samples may use different numbers of bits.

The data may be encoded by different schemes. The information may be digitally compressed by different algorithms or to different degrees. Generally, choices are made about the above factors in order to achieve the desired trade-off between minimizing the bitrate and maximizing the quality of the material when it is played.

If lossy data compression is used on audio or visual data, differences from the original signal will be introduced; if the compression is substantial, or lossy data is decompressed and recompressed, this may become noticeable in the form of compression artifacts. Whether these affect the perceived quality, and if so how much, depends on the compression scheme, encoder power, the characteristics of the input data, the listener's perceptions, the listener's familiarity with artifacts, and the listening or viewing environment.

The encoding bit rate of a multimedia file is its size in bytes divided by the playback time of the recording (in seconds), multiplied by eight. For real-time streaming multimedia, the encoding bit rate is the goodput that is required to avoid playback interruption. The term average bitrate is used in case of variable bitrate multimedia source coding schemes.

In this context, the peak bit rate is the maximum number of bits required for any short-term block of compressed data. A theoretical lower bound for the encoding bit rate for lossless data compression is the source information rate, also known as the entropy rate.

The bitrates in this section are approximately the minimum that the average listener in a typical listening or viewing environment, when using the best available compression, would perceive as not significantly worse than the reference standard. \text{bit rate} = \text{sample rate} \times \text{bit depth} \times \text{channels} For example, the bit rate of a CD-DA recording (44.1 kHz sampling rate, 16 bits per sample and two channels) can be calculated as follows: 44,100 \times 16 \times 2 = 1,411,200\ \text{bit/s} = 1,411.2\ \text{kbit/s} The cumulative size of a length of PCM audio data (excluding a file header or other metadata) can be calculated using the following formula: \text{size in bits} = \text{sample rate} \times \text{bit depth} \times \text{channels} \times \text{time}. The cumulative size in bytes can be found by dividing the file size in bits by the number of bits in a byte, which is eight: \text{size in bytes} = \frac{\text{size in bits}}{8} Therefore, 80 minutes (4,800 seconds) of CD-DA data requires 846,720,000 bytes of storage: \frac{44,100 \times 16 \times 2 \times 4,800}{8} = 846,720,000\ \text{bytes} \approx 847\ \text{MB} \approx 807.5\ \text{MiB} where MiB is mebibytes with binary prefix Mi, meaning 2 20 = 1,048,576.

Text derived from https://en.wikipedia.org/w/index.php?oldid=1378017882 under CC BY-SA 4.0; modifications have been made.

Sources cited in this revision

26 named source(s) extracted from the cited revision. A source with no author is shown by its publication; nothing is invented.