Blow molding

Blow molding (or moulding) is a manufacturing process for forming hollow plastic parts.

Uses your system voice; voice and rate in settings.

≈ 3 min read

Cite, export and learn8 citation formats · 8 exports · lesson and quiz

Names in other languages

No names in other languages are held for this entry yet.

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

Blow molding (or moulding) is a manufacturing process for forming hollow plastic parts. It is also used for forming glass bottles or other hollow shapes. In general, there are three main types of blow molding: extrusion blow molding, injection blow molding, and injection stretch blow molding.

The blow molding process begins with softening plastic by heating a preform or parison. The parison is a tube-like piece of plastic with a hole in one end through which compressed air can enter. The plastic workpiece is then clamped into a mold and air is blown into it.

The air pressure inflates the plastic which conforms to the mold. Once the plastic has cooled and hardened the mold opens and the part is ejected. Water channels within the mold assist cooling.

History

The process principle comes from the idea of glassblowing. Enoch Ferngren and William Kopitke produced a blow molding machine and sold it to Hartford Empire Company in 1938. This was the beginning of the commercial blow molding process.

During the 1940s the variety and number of products were still very limited and therefore blow molding did not take off until later. Once the variety and production rates went up the number of products created soon followed. The technical mechanisms needed to produce hollow-bodied workpieces using the blowing technique were established very early on.

Because glass is very breakable, after the introduction of plastic, plastic was used to replace glass in some cases. The first mass production of plastic bottles was done in America in 1939. Germany started using this technology a little bit later but is currently one of the leading manufacturers of blow molding machines.

In the United States soft drink industry, the number of plastic containers went from zero in 1977 to ten billion pieces in 1999. Today, an even greater number of products are blown and it is expected to keep increasing.

For amorphous metals, also known as bulk metallic glasses, blow molding has been recently demonstrated under pressures and temperatures comparable to plastic blow molding.

Two-stage

In the two-stage injection stretch blow molding process, the plastic is first molded into a "preform" using the injection molding process. These preforms are produced with the necks of the bottles, including threads (the "finish") on one end. These preforms are packaged, and fed later (after cooling) into a reheat stretch blow molding machine.

In the ISBM process, the preforms are heated (typically using infrared heaters) above their glass transition temperature, then blown using high-pressure air into bottles using metal blow molds. The preform is always stretched with a core rod as part of the process.

See also

Blow fill seal Gravimetric blender Mold-A-Rama Molding Plastic forming machine Hydroforming

Bibliography

Extrusion Blow Molding, Hanser-Gardner Publications, Ottmar Brandau, Stretch Blow Molding, PETplanet Publisher GmbH, Yam, K. L., "Encyclopedia of Packaging Technology", John Wiley & Sons, 2009,

Text derived from https://en.wikipedia.org/w/index.php?oldid=1359879282 under CC BY-SA 4.0; modifications have been made.

Words in each sectionHistoryHistoryHistory: 310 words310BibliographyBibliographyBibliography: 48 words48See alsoSee alsoSee also: 11 words11
Words in each section. Measured from the stored article body; sections below the minimum are not plotted.

Provenance

snapshot enwiki-001359879282 · captured 2026-06-17 · ledger · version history

Cite this page as: encyclopegia.org, “Blow molding”, snapshot enwiki-001359879282. https://encyclopegia.org/a/blow-molding

Sources cited in this revision

No external citation was extracted for this revision. That is a statement about the source, not a claim that none exists.