Caltech Intermediate Form

Uses your system voice; voice and rate in settings.

Snapshot

≈ 7 min read

Names in other languages

No names in other languages are held for this entry yet.

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

Caltech Intermediate Form (CIF) is a file format for describing integrated circuits. CIF provides a limited set of graphics primitives that are useful for describing the two-dimensional shapes on the different layers of a chip. The format allows hierarchical description, which makes the representation concise. In addition, it is a terse but human-readable text format. CIF was created by Ivan Sutherland and Ron Ayres in 1976, with improvements by Carlo H. Séquin, Douglas Fairbairn and Stephen Trimberger. The written specification was later updated by Robert Sproull and Richard Lyon and revised by Stephen Trimberger.

Caltech Intermediate Form (CIF) is a file format for describing integrated circuits. CIF provides a limited set of graphics primitives that are useful for describing the two-dimensional shapes on the different layers of a chip. The format allows hierarchical description, which makes the representation concise. In addition, it is a terse but human-readable text format. CIF was created by Ivan Sutherland and Ron Ayres in 1976, with improvements by Carlo H. Séquin, Douglas Fairbairn and Stephen Trimberger. The written specification was later updated by Robert Sproull and Richard Lyon and revised by Stephen Trimberger. L CC; sets the layer to be the CMOS contact cut (see Fig. B.1 for some typical MOS layer names). The BOX statement (or the letter B ) is the most commonly used way of specifying geometry. It describes a rectangle by giving its length, width, center position, and an optional rotation. The format is as follows: B length width xpos ypos [rotation] ; Without the rotation field, the four numbers specify a box the center of which is at (xpos, ypos) and is length across in x and width tall in y. All numbers in CIF are integers that refer to centimicrons of distance, unless subroutine scaling is specified (described later). The optional rotation field contains two numbers that define a vector endpoint starting at the origin. The default value of this field is (1, 0), which is a right-pointing vector. Thus the rotation clause 10 5 defines a 26.6-degree counterclockwise rotation from the normal. Similarly, 10 -10 will rotate clockwise by 45 degrees. Note that the magnitude of this rotation vector has no meaning. The WIRE statement (or the letter W ) is used to construct a path that runs between a set of points. The path can have a nonzero width and has rounded corners. After the WIRE keyword comes the width value and then an arbitrary number of coordinate pairs that describe the endpoints. Figure B.2 shows a sample wire. Note that the endpoint and corner rounding are implicitly handled. The ROUNDFLASH statement (or the letter R ) draws a filled circle, given the diameter and the center coordinate. For example, the statement: R 20 30 40; will draw a circle that has a radius of 10 (diameter of 20), centered at (30, 40). The POLYGON statement (or the letter P ) takes a series of coordinate pairs and draws a filled polygon from them. Since filled polygons must be closed, the first and last coordinate points are implicitly connected and need not be the same. Polygons can be arbitrarily complex, including concavity and self-intersection. Figure B.3 illustrates a polygon statement. C 4; will cause the box to be drawn on that layer. In addition to simply invoking the subroutine, a CALL statement can include transformations to affect the geometry inside the subroutine. Three transformations can be applied to a subroutine in CIF: translation, rotation, and mirroring. Translation is specified as the letter T followed by an x, y offset. These offsets will be added to all coordinates in the subroutine, to translate its graphics across the mask. Rotation is specified as the letter R followed by an x, y vector endpoint that, much like the rotation clause in the BOX statement, defines a line to the origin. The unrotated line has the endpoint (1, 0), which points to the right. Mirroring is available in two forms: MX to mirror in x and MY to mirror in y. Mirroring is a bit confusing, because MX causes a negation of the x coordinate, which effectively mirrors about the y axis. Any number of transformations can be applied to an object and their listed order is the sequence that will be used to apply them. Figure B.4 shows some examples, illustrating the importance of ordering the transformations (notice that Figs. B.4c and B.4d produce different results by rearranging the transformations). Defining subroutines for use in a CALL statement is quite simple. The statements to be packaged are enclosed between DS (definition start) and DF (definition finish) statements. Arguments to the DS statement are the subroutine number and a subroutine scaling factor. There are no arguments to the DF statement. The scaling factor for a subroutine consists of a numerator followed by a denominator that will be applied to all values inside the subroutine. This scaling allows large numbers to be expressed with fewer digits and allows ease of rescaling a design. The scale factor cannot be changed for each invocation of the subroutine since it is applied to the definition. As an example, the subroutine of Fig. B.4 can be described formally as follows: DS 10 20 2; B10 20 5 5; W1 5 5 10 15; DF; Note that the scale factor is 20/2, which allows the trailing zero to be dropped from all values inside the subroutine. Arbitrary depth of hierarchy is allowed in CIF subroutines. Forward references are allowed provided that a subroutine is defined before it is used. Thus the sequence: DS 10; ... C 11; DF; DS 11; ... DF; C 10; is legal, but the sequence: C 11; DS 11; ... DF; is not. This is because the actual invocation of subroutine 11 does not occur until after its definition in the first example.

BNF grammar

The following is the grammar for the CIF format with cifFile being the top level grammar node. cifFile ::= (blank* command? semi)* endCommand blank* command ::= primCommand | defDeleteCommand | defStartCommand semi (blank* primCommand? semi)* defFinishCommand primCommand ::= polygonCommand | boxCommand | roundFlashCommand | wireCommand | layerCommand | callCommand | userExtensionCommand | commentCommand polygonCommand ::= "P" path boxCommand ::= "B" integer sep integer sep point (sep point)? roundFlashCommand ::= "R" integer sep point wireCommand ::= "W" integer sep path layerCommand ::= "L" blank* shortname defStartCommand ::= "D" blank* "S" integer (sep integer sep integer)? defFinishCommand ::= "D" blank* "F" defDeleteCommand ::= "D" blank* "D" integer callCommand ::= "C" integer transformation userExtensionCommand ::= digit userText commentCommand ::= "(" commentText ")" endCommand ::= "E" transformation ::= (blank* ("T" point |"M" blank* "X" |"M" blank* "Y" |"R" point)*)* path ::= point (sep point)* point ::= sInteger sep sInteger sInteger ::= sep* "-"? integerD integer ::= sep* integerD integerD ::= digit+ shortname ::= c c? c? c? c ::= digit | upperChar userText ::= userChar* commentText ::= commentChar* | commentText "(" commentText ")" commentText semi ::= blank* ";" blank* sep ::= upperChar | blank digit ::= "0" | "1" | ... | "9" upperChar ::= "A" | "B" | ... | "Z" blank ::= any ASCII character except digit, upperChar, "-", "(", ")", or ";" userChar ::= any ASCII character except ";" commentChar ::= any ASCII character except "(" or ")"

See also

GDS II stream format OASIS (Open Artwork System Interchange Standard) EDIF, a vendor neutral file format made in 90s

Text derived from https://en.wikipedia.org/w/index.php?oldid=1318785836 under CC BY-SA 4.0; modifications have been made.

Provenance

snapshot enwiki-001318785836 · captured 1761431005.0 · version history

Cite this page as: encyclopegia.org, “Caltech Intermediate Form”, snapshot enwiki-001318785836. https://encyclopegia.org/a/caltech-intermediate-form

Sources cited in this revision

1 named source(s) extracted from the cited revision. A source with no author is shown by its publication; nothing is invented.