Capacitor types
≈ 22 min read
Names in other languages
No names in other languages are held for this entry yet.
Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.
Capacitors are manufactured in many styles, forms, dimensions, and from a large variety of materials. They all contain at least two electrical conductors, called plates, separated by an insulating layer (dielectric). Capacitors are widely used as parts of electrical circuits in many common electrical devices. Capacitors, together with resistors and inductors, belong to the group of passive components in electronic equipment. Small capacitors are used in electronic devices to couple signals between stages of amplifiers, as components of electric filters and tuned circuits, or as parts of power supply systems to smooth rectified current. Larger capacitors are used for energy storage in such applications as strobe lights, as parts of some types of electric motors, or for power factor correction in AC power distribution systems. Standard capacitors have a fixed value of capacitance, but adjustable capacitors are frequently used in tuned circuits. Different types are used depending on required capacitance, working voltage, current handling capacity, and other properties. While, in absolute figures, the most commonly manufactured capacitors are integrated into dynamic random-access memory, flash memory, and other device chips, this article covers the discrete components.
Capacitors are manufactured in many styles, forms, dimensions, and from a large variety of materials. They all contain at least two electrical conductors, called plates, separated by an insulating layer (dielectric). Capacitors are widely used as parts of electrical circuits in many common electrical devices. Capacitors, together with resistors and inductors, belong to the group of passive components in electronic equipment. Small capacitors are used in electronic devices to couple signals between stages of amplifiers, as components of electric filters and tuned circuits, or as parts of power supply systems to smooth rectified current. Larger capacitors are used for energy storage in such applications as strobe lights, as parts of some types of electric motors, or for power factor correction in AC power distribution systems. Standard capacitors have a fixed value of capacitance, but adjustable capacitors are frequently used in tuned circuits. Different types are used depending on required capacitance, working voltage, current handling capacity, and other properties. While, in absolute figures, the most commonly manufactured capacitors are integrated into dynamic random-access memory, flash memory, and other device chips, this article covers the discrete components.
General characteristics
Conventional construction
A conventional capacitor stores electric energy as static electricity by charge separation in an electric field between two electrode plates. The charge carriers are typically electrons. The amount of charge stored per unit voltage is essentially a function of the size of the plates, the plate material's properties, the properties of the dielectric material placed between the plates, and the separation distance (i.e. dielectric thickness). The potential difference between the plates is limited by the properties of the dielectric material and the separation distance. Nearly all conventional industrial capacitors except some special types such as "feed-through capacitors", are constructed as "plate capacitors" even if their electrodes and the dielectric between are wound or rolled. The capacitance C of a plate capacitor is C= \frac{\varepsilon A}{d} . The capacitance increases with the area A of the plates and with the permittivity ε of the dielectric material, and decreases with the plate separation distance d. The capacitance is therefore greatest in devices made from materials with a high permittivity, large plate area, and small distance between plates.
Electrochemical construction
Another type – the electrochemical capacitor – makes use of two other storage principles to store electric energy. In contrast to ceramic, film, and electrolytic capacitors, supercapacitors (also known as electrical double-layer capacitors (EDLC) or ultracapacitors) do not have a conventional dielectric. The capacitance value of an electrochemical capacitor is determined by two high-capacity storage principles. These principles are: electrostatic storage within Helmholtz double layers achieved on the phase interface between the surface of the electrodes and the electrolyte (double-layer capacitance); and electrochemical storage achieved by a faradaic electron charge-transfer by specifically absorbed ions with redox reactions (pseudocapacitance). Unlike batteries, in these reactions, the ions simply cling to the atomic structure of an electrode without making or breaking chemical bonds, and no or negligibly small chemical modifications are involved in charge/discharge. The ratio of the storage resulting from each principle can vary greatly, depending on electrode design and electrolyte composition. Pseudocapacitance can increase the capacitance value by as much as an order of magnitude over that of the double-layer by itself.
Classification
Capacitors are divided into two mechanical groups: Fixed-capacitance devices with a constant capacitance and variable capacitors. Variable capacitors are made as trimmers, that are either adjusted only during circuit calibration, or a device tunable during operation of the electronic instrument. The most common group is the fixed capacitors. Many are named based on the type of dielectric. For a systematic classification these characteristics cannot be used, because one of the oldest, the electrolytic capacitor, is named instead by its cathode construction. So the most-used names are simply historical. The most common kinds of capacitors are: Ceramic capacitors have a ceramic dielectric. Film and paper capacitors are named for their dielectrics. Aluminum, tantalum and niobium electrolytic capacitors are named after the material used as the anode and the construction of the cathode (electrolyte). Polymer capacitors are aluminum, tantalum or niobium electrolytic capacitors with conductive polymer as electrolyte. Supercapacitor is the family name for: Double-layer capacitors were named for the physical phenomenon of the Helmholtz double-layer. Pseudocapacitors were named for their ability to store electric energy electro-chemically with reversible faradaic charge-transfer. Hybrid capacitors combine double-layer and pseudocapacitors to increase power density. Silver mica, glass, silicon, air-gap and vacuum capacitors are named for their dielectric. In addition to the above shown capacitor types, which derived their name from historical development, there are many individual capacitors that have been named based on their application. They include: Power capacitors, motor capacitors, DC-link capacitors, suppression capacitors, audio crossover capacitors, lighting ballast capacitors, snubber capacitors, coupling, decoupling or bypassing capacitors. Often, more than one capacitor family is employed for these applications, e.g. interference suppression can use ceramic capacitors or film capacitors. Other kinds of capacitors are discussed in the #Special capacitors section. File: Kondensator-Block-Kondensator-Wiki-07-02-11.jpg|Stacked paper capacitor from 1923 for noise decoupling (blocking) in telegraph lines File: Kondensator cgs cm.jpg|Wound metallized paper capacitor from the early 1930s in hardpaper case, capacitance value specified in "cm" in the cgs system; 5,000 cm corresponds to 0.0056 μF. File:Elektrolytkondensator-Flüssigkeits-Ko-Wiki-07-02-20.jpg|Folded wet aluminum electrolytic capacitor, Bell System 1929, view onto the folded anode, which was mounted in a squared housing (not shown) filled with liquid electrolyte File: PaperElectrolyticCapacitors.jpg|Two 8 μF, 525 V wound wet aluminum electrolytic capacitors in paper housing sealed with tar out of a 1930s radio. File:MLCC-Kondensatoren-1.png| Multi-layer ceramic capacitors (MLCC chips) for SMD mounting File:Capacitors x2y.jpg|Ceramic X2Y decoupling capacitors File:Condensador ceramico.jpg| Ceramic EMI suppression capacitors for connection to the supply mains (safety capacitor) File: Kerko-HV-Scheibenkondensator.png| High voltage ceramic power capacitor File:Folien-Kondensator-Wiki-07-02-25-P1040367b.jpg|Radial style (single ended) for through-hole solder mounting on printed circuit boards File:Folko-SMD.png|SMD style for printed circuit board surface mounting, with metallized contacts on two opposite edges File:Snubber-P1180579b.JPG|Radial style with heavy-duty solder terminals for snubber applications and high surge pulse loads File:GTO-P1180590b.JPG|Heavy-duty snubber capacitor with screw terminals File:Power-kondensator.jpg|Power film capacitor for AC power-factor correction (PFC), packaged in a cylindrical metal can File: Power-Quaderbecher.png|Power film capacitor in rectangular housing File:Leistungskondensatoren-DESY-P1040621.JPG|One of several energy storage power film capacitor banks, for magnetic field generation at the Hadron-Electron Ring Accelerator (HERA), located on the DESY site in Hamburg, Germany File:Condensor bank 150kV - 75MVAR.jpg|75MVAR substation capacitor bank at 150 kV File:Wet-Al-Elcap-Construction.png| Schematic representation of the structure of a wound aluminum electrolytic capacitor with non solid (liquid) electrolyte File:Tantalum-Sintered-MnO2-slug.jpg|Schematic representation of the structure of a sintered tantalum electrolytic capacitor with solid electrolyte and the cathode contacting layers File:Wiki-Al-Elkos-P1090313-2.jpg| Axial, radial (single ended) and V-chip styles of aluminum electrolytic capacitors File:Snap-In Electrolytic Capacitor.jpg|Snap-in style of aluminum electrolytic capacitors for power applications File:Arduino capacitors-1.jpg|SMD style for surface mounting of aluminum electrolytic capacitors with polymer electrolyte File:Kondensator-Ta-Chips-Wiki-07-02-11.jpg|Tantalum electrolytic chip capacitors for surface mounting Class 1, Memory backup, discharge current in mA = 1 • C (F) Class 2, Energy storage, discharge current in mA = 0.4 • C (F) • V (V) Class 3, Power, discharge current in mA = 4 • C (F) • V (V) Class 4, Instantaneous power, discharge current in mA = 40 • C (F) • V (V) File:OneFarad5.5Velectrolyticcapacitor.jpg| Double-layer capacitor with 1 F at 5.5 V for data retention when power is off. File:Lithium Ionen Kondensator.jpg|Radial (single ended) style of lithium ion capacitors for high energy density File:Skeleton Technologies ultracapacitators.jpg|Supercapacitors File:Silver mica capacitors.jpg|Some 1 nF × 500 VDC rated silver mica capacitors File:Vacuum capacitor with uranium glass.jpg| Vacuum capacitor with uranium glass encapsulation File:Drehkondensator-sw.jpg| Air gap tuning capacitor File:VacuumCapacitorTelefunkenRK500.jpg| Vacuum tuning capacitor File:Folientrimmer-P1130559-1.jpg|Trimmer capacitor for through hole mounting File:Schnittdarstellung Keramiktrimmer.svg| Trimmer capacitor for surface mounting
Comparison of types
File:MLCC-Kap-versus-Frequenz-engl.svg | Frequency dependence of capacitance for ceramic class 2 capacitors (NP0 class 1 for comparisation) File:Folko-Kurve-C-f-Frequenz-4.png| Frequency dependence of capacitance for film capacitors with different film materials For electrolytic capacitors with non-solid electrolyte, mechanical motion of the ions occurs. Their movability is limited so that at higher frequencies not all areas of the roughened anode structure are covered with charge-carrying ions. As higher the anode structure is roughened as more the capacitance value decreases with increasing frequency. Low voltage types with highly roughened anodes display capacitance at 100 kHz approximately 10 to 20% of the value measured at 100 Hz. File:Delta-Cap-versus-Spannung-engl.png|Simplified diagram of the change in capacitance as a function of the applied voltage for 25 V capacitors in different kind of ceramic grades File:Delta-Cap-versus-Spannung-X7R-engl.png|Simplified diagram of the change in capacitance as a function of applied voltage for X7R ceramics with different rated voltages \ Z = |Z| e^{j\theta} The magnitude \scriptstyle |Z| represents the ratio of the voltage difference amplitude to the current amplitude, \scriptstyle j is the imaginary unit, while the argument \scriptstyle \theta gives the phase difference between voltage and current. In capacitor data sheets, only the impedance magnitude |Z| is specified, and simply written as "Z" so that the formula for the impedance can be written in Cartesian form \ Z = R + jX where the real part of impedance is the resistance \scriptstyle R (for capacitors \scriptstyle ESR ) and the imaginary part is the reactance \scriptstyle X . As shown in a capacitor's series-equivalent circuit, the real component includes an ideal capacitor C , an inductance L (ESL) and a resistor R (ESR) . The total reactance at the angular frequency \omega therefore is given by the geometric (complex) addition of a capacitive reactance (Capacitance) X_C= -\frac{1}{\omega C} and an inductive reactance (Inductance): X_L=\omega L_{\mathrm{ESL}} . To calculate the impedance \scriptstyle Z the resistance has to be added geometrically and then Z is given by Z=\sqrt{{ESR}^2 + (X_\mathrm{C} + (-X_\mathrm{L}))^2} . The impedance is a measure of the capacitor's ability to pass alternating currents. In this sense the impedance can be used like Ohms law Z = \frac{\hat u}{\hat \imath} = \frac{U_\mathrm{eff}}{I_\mathrm{eff}}. to calculate either the peak or the effective value of the current or the voltage. In the special case of resonance, in which the both reactive resistances X_C= -\frac{1}{\omega C} and X_L=\omega L_{\mathrm{ESL}} have the same value ( X_C=X_L ), then the impedance will only be determined by {ESR} . The impedance specified in the datasheets often show typical curves for the different capacitance values. With increasing frequency as the impedance decreases down to a minimum. The lower the impedance, the more easily alternating currents can be passed through the capacitor. At the apex, the point of resonance, where XC has the same value than XL, the capacitor has the lowest impedance value. Here only the ESR determines the impedance. With frequencies above the resonance the impedance increases again due to the ESL of the capacitor. The capacitor becomes an inductance. As shown in the graph, the higher capacitance values can fit the lower frequencies better while the lower capacitance values can fit better the higher frequencies. Aluminum electrolytic capacitors have relatively good decoupling properties in the lower frequency range up to about 1 MHz due to their large capacitance values. This is the reason for using electrolytic capacitors in standard or switched-mode power supplies behind the rectifier for smoothing application. Ceramic and film capacitors are already out of their smaller capacitance values suitable for higher frequencies up to several 100 MHz. They also have significantly lower parasitic inductance, making them suitable for higher frequency applications, due to their construction with end-surface contacting of the electrodes. To increase the range of frequencies, often an electrolytic capacitor is connected in parallel with a ceramic or film capacitor. Many new developments are targeted at reducing parasitic inductance (ESL). This increases the resonance frequency of the capacitor and, for example, can follow the constantly increasing switching speed of digital circuits. Miniaturization, especially in the SMD multilayer ceramic chip capacitors (MLCC), increases the resonance frequency. Parasitic inductance is further lowered by placing the electrodes on the longitudinal side of the chip instead of the lateral side. The "face-down" construction associated with multi-anode technology in tantalum electrolytic capacitors further reduced ESL. Capacitor families such as the so-called MOS capacitor or silicon capacitors offer solutions when capacitors at frequencies up to the GHz range are needed. \tan \delta = ESR \cdot \omega C Capacitors with very low losses, such as ceramic Class 1 and Class 2 capacitors, specify resistive losses with a quality factor (Q). Ceramic Class 1 capacitors are especially suitable for LC resonant circuits with frequencies up to the GHz range, and precise high and low pass filters. For an electrically resonant system, Q represents the effect of electrical resistance and characterizes a resonator's bandwidth B relative to its center or resonant frequency f_0 . Q is defined as the reciprocal value of the dissipation factor. Q = \frac{1}{\tan \delta} = \frac{f_0}{B} \ A high Q value is for resonant circuits a mark of the quality of the resonance. P = I^2 \cdot ESR The same power loss can be written with the dissipation factor \tan \delta as P = \frac{U^2 \cdot \tan \delta}{2\pi f \cdot C} The internal generated heat has to be distributed to the ambient. The temperature of the capacitor, which is established on the balance between heat produced and distributed, shall not exceed the capacitors maximum specified temperature. Hence, the ESR or dissipation factor is a mark for the maximum power (AC load, ripple current, pulse load, etc.) a capacitor is specified for. AC currents may be a: ripple current—an effective (RMS) AC current, coming from an AC voltage superimposed of a DC bias, a pulse current—an AC peak current, coming from a voltage peak, or an AC current—an effective (RMS) sinusoidal current Ripple and AC currents mainly warms the capacitor body. By this currents internal generated temperature influences the breakdown voltage of the dielectric. Higher temperature lower the voltage proof of all capacitors. In wet electrolytic capacitors higher temperatures force the evaporation of electrolytes, shortening the life time of the capacitors. In film capacitors higher temperatures may shrink the plastic film changing the capacitor's properties. Pulse currents, especially in metallized film capacitors, heat the contact areas between end spray (schoopage) and metallized electrodes. This may reduce the contact to the electrodes, heightening the dissipation factor. For safe operation, the maximal temperature generated by any AC current flow through the capacitor is a limiting factor, which in turn limits AC load, ripple current, pulse load, etc. I_p = C \cdot dv/dt where: I_p is in A; C in μF; dv/dt in V/μs The permissible pulse current capacity of a metallized film capacitor generally allows an internal temperature rise of 8 to 10 K. In the case of metallized film capacitors, pulse load depends on the properties of the dielectric material, the thickness of the metallization and the capacitor's construction, especially the construction of the contact areas between the end spray and metallized electrodes. High peak currents may lead to selective overheating of local contacts between end spray and metallized electrodes which may destroy some of the contacts, leading to increasing ESR. For metallized film capacitors, so-called pulse tests simulate the pulse load that might occur during an application, according to a standard specification. IEC 60384 part 1, specifies that the test circuit is charged and discharged intermittently. The test voltage corresponds to the rated DC voltage and the test comprises 10000 pulses with a repetition frequency of 1 Hz. The pulse stress capacity is the pulse rise time. The rated pulse rise time is specified as 1/10 of the test pulse rise time. The pulse load must be calculated for each application. A general rule for calculating the power handling of film capacitors is not available because of vendor-related internal construction details. To prevent the capacitor from overheating the following operating parameters have to be considered: peak current per μF Pulse rise or fall time dv/dt in V/μs relative duration of charge and discharge periods (pulse shape) maximum pulse voltage (peak voltage) peak reverse voltage; Repetition frequency of the pulse Ambient temperature Heat dissipation (cooling) Higher pulse rise times are permitted for pulse voltage lower than the rated voltage. Examples for calculations of individual pulse loads are given by many manufactures, e.g. WIMA and Kemet. u(t) = U_0 \cdot \mathrm{e}^{-t/\tau_\mathrm{s}}, With stored DC voltage U_0 and self-discharge constant \tau_\mathrm{s} = R_\mathrm{ins} \cdot C Thus, after \tau_\mathrm{s}\, voltage U_0 drops to 37% of the initial value. The self-discharge constant is an important parameter for the insulation of the dielectric between the electrodes of ceramic and film capacitors. For example, a capacitor can be used as the time-determining component for time relays or for storing a voltage value as in a sample and hold circuits or operational amplifiers. Class 1 ceramic capacitors have an insulation resistance of at least 10 GΩ, while class 2 capacitors have at least 4 GΩ or a self-discharge constant of at least 100 s. Plastic film capacitors typically have an insulation resistance of 6 to 12 GΩ. This corresponds to capacitors in the uF range of a self-discharge constant of about 2000–4000 s. Insulation resistance respectively the self-discharge constant can be reduced if humidity penetrates into the winding. It is partially strongly temperature dependent and decreases with increasing temperature. Both decrease with increasing temperature. In electrolytic capacitors, the insulation resistance is defined as leakage current. E_\mathrm{stored} = \frac{1}{2} C V^2, thus a capacitor having a dielectric half as thick as another has 4 times higher capacitance but voltage proof, yielding an equal maximum energy density. Therefore, dielectric thickness does not affect energy density within a capacitor of fixed overall dimensions. Using a few thick layers of dielectric can support a high voltage, but low capacitance, while thin layers of dielectric produce a low breakdown voltage, but a higher capacitance. This assumes that neither the electrode surfaces nor the permittivity of the dielectric change with the voltage proof. A simple comparison with two existing capacitor series can show whether reality matches theory. The comparison is easy, because the manufacturers use standardized case sizes or boxes for different capacitance/voltage values within a series. In reality modern capacitor series do not fit the theory. For electrolytic capacitors the sponge-like rough surface of the anode foil gets smoother with higher voltages, decreasing the surface area of the anode. But because the energy increases squared with the voltage, and the surface of the anode decreases lesser than the voltage proof, the energy density increases clearly. For film capacitors the permittivity changes with dielectric thickness and other mechanical parameters so that the deviation from the theory has other reasons. Comparing the capacitors from the table with a supercapacitor, the highest energy density capacitor family. For this, the capacitor 25 F/2.3 V in dimensions D × H = 16 mm × 26 mm from Maxwell HC Series, compared with the electrolytic capacitor of approximately equal size in the table. This supercapacitor has roughly 5000 times higher capacitance than the 4700/10 electrolytic capacitor but of the voltage and has about 66,000 mWs (0.018 Wh) stored electrical energy, approximately 100 times higher energy density (40 to 280 times) than the electrolytic capacitor. |- style="text-align:center;" | | | |- style="text-align:center;" | | | |- style="text-align:center;" | |- style="text-align:center;" | | | | | | |- style="text-align:center;" | Capacitor | Polarized capacitor Electrolytic capacitor | Bipolar electrolytic capacitor | Feed through capacitor | Trimmer capacitor | Variable capacitor 105K 330 V implies a capacitance of 10 × 10 5 pF = 1 μF (K = ±10%) with a working voltage of 330 V. 473M 100 V implies a capacitance of 47 × 10 3 pF = 47 nF (M = ±20%) with a working voltage of 100 V. Capacitance, tolerance and date of manufacture can be indicated with a short code specified in IEC/EN 60062. Examples of short-marking of the rated capacitance (microfarads): μ47 = 0.47 μF, 4μ7 = 4.7 μF, 47μ = 47 μF The date of manufacture is often printed in accordance with international standards. Version 1: coding with year/week numeral code, "1208" is "2012, week number 8". Version 2: coding with year code/month code. The year codes are: "R" = 2003, "S"= 2004, "T" = 2005, "U" = 2006, "V" = 2007, "W" = 2008, "X" = 2009, "A" = 2010, "B" = 2011, "C" = 2012, "D" = 2013, etc. Month codes are: "1" to "9" = Jan. to Sept., "O" = October, "N" = November, "D" = December. "X5" is then "2009, May" For very small capacitors like MLCC chips no marking is possible. Here only the traceability of the manufacturers can ensure the identification of a type.
Colour coding
Capacitors do not use color coding. File:Polarity-wet-Al-Elcaps.jpg File:Polarity-rectangular-chips.jpg Aluminum e-caps with non-solid electrolyte have a polarity marking at the cathode (minus) side. Aluminum, tantalum, and niobium e-caps with solid electrolyte have a polarity marking at the anode (plus) side. Supercapacitors are marked at the minus side.
Market segments
Discrete capacitors today are industrial products produced in very large quantities for use in electronic and in electrical equipment. Globally, the market for fixed capacitors was estimated at US$18 billion in 2008 for 1.4 trillion pieces. This market is dominated by ceramic capacitors with estimate of approximately one trillion items per year. Detailed estimated figures in value for the main capacitor families are: Ceramic capacitors—US$8.3 billion (46%); Aluminum electrolytic capacitors—US$3.9 billion (22%); Film capacitors and Paper capacitors—US$2.6 billion, (15%); Tantalum electrolytic capacitors—US$2.2 billion (12%); Super capacitors (Double-layer capacitors)—US$0.3 billion (2%); and Others like silver mica and vacuum capacitors—US$0.7 billion (3%). All other capacitor types are negligible in terms of value and quantity compared with the above types.
Text derived from https://en.wikipedia.org/w/index.php?oldid=1372683608 under CC BY-SA 4.0; modifications have been made.