Carburetor
2280 carburetor A carburetor (also spelled carburettor or carburetter) is a device used by a gasoline internal combustion engine to control and mix air and fuel entering the engine.
≈ 7 min read
Carburetor. encyclopegia.org, snapshot enwiki-001378333368. /a/carburetor
Names in other languages
No names in other languages are held for this entry yet.
Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.
2280 carburetor A carburetor (also spelled carburettor or carburetter) is a device used by a gasoline internal combustion engine to control and mix air and fuel entering the engine. The primary method of adding fuel to the intake air is through the Venturi effect or Bernoulli's principle or with a pitot tube in the main metering circuit, though various other components are also used to provide extra fuel or air in specific circumstances.
Since the 1990s, carburetors have been largely replaced by fuel injection for cars and trucks, but carburetors are still used by some small engines (e.g. lawnmowers, generators, and concrete mixers), motorcycles, and smaller outboard engines. In addition, they are still widely used on piston-engine–driven aircraft.
Diesel engines have always used fuel injection instead of carburetors, as they do not compress an air-fuel mix and instead require fuel injection much later in the compression stroke.
Etymology
The term "carburetor" is derived from the English verb carburet, meaning "to charge with hydrocarbons"; in early motoring books the product of the carburetor is carburetted air, i.e. air charged with hydrocarbon vapour. This meaning superseded that from the late eighteenth century in which carburet was a noun for which we now use the word carbide.
A carburetor charges the intake air with vapour from a hydrocarbon-based fuel, such as petrol or autogas. The name is spelled "carburetor" in American English and "carburettor" in British English. Colloquial abbreviations include "carb" in the UK and North America or "carby" in Australia.
Main metering circuit
The main metering circuit usually consists of barrel/s which reduces to a narrow part where the air is at its highest speed, forming a choke or venturi. Fuel is usually introduced into the air stream at that narrow part through small tubes leading from the main jet.
The change in area is only necessary for a Venturi carburetor but in other configurations the barrel/s can be of constant area with the fuel entry anywhere along it. Downstream of a choke or venturi is a throttle (usually in the form of a butterfly valve) which is used to control the amount of air entering the carburetor.
In a car, this throttle is usually mechanically connected to the vehicle's throttle pedal, which varies engine speed. At lesser throttle openings, the air speed may be insufficient to maintain the main fuel flow, so then the fuel may be supplied by the carburetor's idle and off-idle circuits usually near the narrow gap between the edge of the butterfly plate and the body to give sufficient local air speed.
At greater throttle openings, the speed of air increases, which lowers the pressure of the air and draws more fuel into the airstream. At the same time, the reduced manifold vacuum results in less fuel flow through the idle and off-idle circuits.
Off-idle circuit
Many carburetors use an off-idle circuit, which includes an additional fuel jet which is briefly used as the throttle starts to open. This jet is located in a low-pressure area caused by the high air speed near the (partly closed) throttle. The additional fuel it provides is used to compensate for the reduced vacuum that occurs when the throttle is opened, thus smoothing the transition from the idle circuit to the main metering circuit.
Power valve
In a four-stroke engine it is often desirable to provide extra fuel to the engine at high loads (to increase the power output and reduce engine knocking). A 'power valve', which is a spring-loaded valve in the carburetor that is held shut by engine vacuum, is often used to do so.
As the airflow through the carburetor increases, the reduced manifold vacuum pulls the power valve open, allowing more fuel into the main metering circuit. In a two-stroke engine, the carburetor power valve operates in the opposite manner: in most circumstances the valve allows extra fuel into the engine, then at a certain engine RPM it closes to reduce the fuel entering the engine.
This is done in order to extend the engine's maximum RPM, since many two-stroke engines can temporarily achieve higher RPM with a leaner air-fuel ratio. This is not to be confused with the unrelated exhaust power valve arrangements used on two-stroke engines.
Accelerator pump
While the main metering circuit can adequately supply fuel to the engine in steady-state conditions, the inertia of fuel (being higher than that of air) causes a temporary shortfall as the throttle is opened. Therefore, an accelerator pump is often used to briefly provide extra fuel as the throttle is opened.
When the driver presses the throttle pedal, a small piston or diaphragm pump injects extra fuel directly into the carburetor throat. The accelerator pump can also be used to "prime" an engine with extra fuel prior to attempting a cold start.
Float chamber
In order to ensure an adequate supply at all times, carburetors include a reservoir of fuel, called a "float chamber" or "float bowl". Fuel is delivered to the float chamber by a fuel pump or by gravity with the fuel tank located higher than the carburetor. A floating inlet valve regulates the fuel entering the float chamber, assuring a constant level.
In some small engines that may instead of a float chamber just use a fuel tank close below the carburetor and use the fuel suction to supply the fuel. Unlike in a fuel injected engine, the fuel system in a carbureted engine is not pressurized.
For engines where the intake air travelling through the carburetor is pressurized (such as where the carburetor is downstream of a supercharger) the entire carburetor must be contained in an airtight pressurized box to operate. However, this is not necessary where the carburetor is upstream of the supercharger.
Problems of fuel boiling and vapor lock can occur in carbureted engines, especially in hotter climates. Since the float chamber is located close to the engine, heat from the engine (including for several hours after the engine is shut off) can cause the fuel to heat up to the point of vaporization.
This causes air bubbles in the fuel (similar to the air bubbles that necessitate brake bleeding), which prevents the flow of fuel and is known as 'vapor lock'. When a carburetor uses the Bernoulli principle there is a vent from the float chamber to ambient air and it prevents the fuel from over-pressuring and allows for fuel/air correction at changes in ambient air pressure, and in carburetors with a Venturi, and with a Pitot tube, each vent goes to the air entry flow for the same benefits.
Diaphragm chamber
If an engine must be operated when the carburetor is not in an upright orientation (for example in a chainsaw or airplane), a float chamber and gravity activated float valve would not be suitable. Instead, a diaphragm chamber is typically used. This consists of a flexible diaphragm on one side of the fuel chamber, connected to a needle valve which regulates the fuel entering the chamber.
As the flowrate of the air in the chamber (controlled by the throttling valve/butterfly valve) decreases, the diaphragm moves inward (downward), which closes the needle valve to admit less fuel. As the flowrate of the air in the chamber increases, the diaphragm moves outward (upward) which opens the needle valve to admit more fuel, allowing the engine to generate more power.
A balanced state is reached which creates a steady fuel reservoir level, that remains constant in any orientation.
See also
Bernoulli's principle Fuel injection Humidifier List of auto parts List of carburetor manufacturers Venturi effect
Text derived from https://en.wikipedia.org/w/index.php?oldid=1378333368 under CC BY-SA 4.0; modifications have been made.