Characteristic impedance

drawn as two black wires.

Uses your system voice; voice and rate in settings.

≈ 8 min read

Cite, export and learn8 citation formats · 8 exports · lesson and quiz

Names in other languages

No names in other languages are held for this entry yet.

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

drawn as two black wires. At a distance into the line, there is current phasor traveling through each wire, and there is a voltage difference phasor between the wires (bottom voltage minus top voltage).

If is the characteristic impedance of the line, then for a wave moving rightward, or for a wave moving leftward. where a source is coupled to a load with a transmission line having characteristic impedance The characteristic impedance or surge impedance (usually written ) of a uniform transmission line is the ratio of the amplitudes of voltage and current of a wave travelling in one direction along the line in the absence of reflections in the other direction. Equivalently, it can be defined as the input impedance of a transmission line when its length is infinite.

Characteristic impedance is determined by the geometry and materials of the transmission line and, for a uniform line, is not dependent on its length. The SI unit of characteristic impedance is the ohm. The characteristic impedance of a lossless transmission line is purely real, with no reactive component (see below).

Energy supplied by a source at one end of such a line is transmitted through the line without being dissipated in the line itself. A transmission line of finite length (lossless or lossy) that is terminated at one end with an impedance equal to the characteristic impedance appears to the source like an infinitely long transmission line and produces no reflections.

Z_0 = \sqrt{ \frac{R + j\omega L}{G + j\omega C}\, } where This expression extends to DC by letting tend to 0. A surge of energy on a finite transmission line will see an impedance of prior to any reflections returning; hence surge impedance is an alternative name for characteristic impedance.

Although an infinite line is assumed, since all quantities are per unit length, the “per length” parts of all the units cancel, and the characteristic impedance is independent of the length of the transmission line. The voltage and current phasors on the line are related by the characteristic impedance as: Z_\text{0} = \frac{V_{(+)}}{I_{(+)}} =-\frac{V_{(-)}}{I_{(-)}} where the subscripts (+) and (−) mark the separate constants for the waves traveling forward (+) and backward (−).

The rightmost expression has a negative sign because the current in the backward wave has the opposite direction to current in the forward wave.

Characteristic admittance

is drawn as two black wires. At a distance x into the line, there is current phasor I(x) traveling through each wire, and there is a voltage difference phasor V(x) between the wires (bottom voltage minus top voltage). If Y_0 is the characteristic admittance of the line, then I(x) / V(x) = Y_0 for a wave moving rightward, or I(x)/V(x) = -Y_0 for a wave moving leftward.

Characteristic admittance is the mathematical inverse of the characteristic impedance. The general expression for the characteristic admittance of a transmission line is as follows: Y_0=\sqrt{\frac{G+j\omega C}{R+j\omega L}} The current and voltage phasors on the line are related by the characteristic admittance as: \frac{I^+}{V^+} = Y_0 = -\frac{I^-}{V^-} where the superscripts + and - represent forward- and backward-traveling waves, respectively. \begin{align} v(x,t) &= V(x) e^{j \omega t}\\[.5ex] i(x,t) &= I(x) e^{j \omega t} \end{align} Take the positive direction for and in the loop to be clockwise.

Substitution in the telegraph equations and factoring out the time dependence e^{j \omega t} now gives: \begin{align} \frac{\mathrm{d}V}{\mathrm{d}x} &= -\left( R + j \omega L \right) I = -Z I,\\[.5ex] \frac{\mathrm{d}I}{\mathrm{d}x} &= -\left( G + j \omega C \right) V = -Y V, \end{align} with impedance and admittance . Derivation and substitution of these two first-order differential equations results in two uncoupled second-order differential equations: \begin{align} \frac{\mathrm{d}^2 V}{\mathrm{d}x^2} &= k^2 V,\\[.5ex] \frac{\mathrm{d}^2 I}{\mathrm{d}x^2} &= k^2 I, \end{align} with and called the propagation constant.

The solution to these types of equations can be written as: \begin{align} V(x) &= A e^{-k x} + B e^{k x}\\[.5ex] I(x) &= A_{1} e^{-k x} + B_{1} e^{k x} \end{align} with , , and the constants of integration. Substituting these constants in the first-order system gives: \begin{align} A_1 &= \hphantom{-}A \frac{k}{R+ j \omega L}\\[.5ex] B_1 &= -B \frac{k}{R + j \omega L} \end{align} where \frac{A}{A_1} = -\frac{B}{B_1} = \frac{R + j \omega L}{k} = \sqrt{\frac{R+ j\omega L}{G + j \omega C}} = \sqrt{\frac{Z}{Y}} = Z_{0}.

It can be seen that the constant , defined in the above equations has the dimensions of impedance (ratio of voltage to current) and is a function of primary constants of the line and operating frequency. It is called the of the transmission line.

The general solution of the telegrapher's equations can now be written as: \begin{align} v(x,t) &= V(x) e^{j \omega t} = A e^{-\alpha x}e^{j(\omega t - \beta x)} + B e^{\alpha x}e^{j(\omega t + \beta x)} \\[.5ex] i(x,t) &= I(x) e^{j \omega t} = \frac{A}{Z_0} e^{-\alpha x}e^{j(\omega t - \beta x)} - \frac{B}{Z_0} e^{\alpha x}e^{j(\omega t + \beta x)} \end{align} Both the solution for the voltage and the current can be regarded as a superposition of two travelling waves in the and directions. For typical transmission lines, that are carefully built from wire with low loss resistance and small insulation leakage conductance ; further, used for high frequencies, the inductive reactance and the capacitive admittance will both be large.

In those cases, the phase constant and characteristic impedance are typically very close to being real numbers: \begin{align} \beta & = \text{Im}\{k\} \approx \omega \sqrt{L C} \\[.5ex] Z_{0} & \approx \sqrt{\frac{L}{C}} \end{align} Manufacturers make commercial cables to approximate this condition very closely over a wide range of frequencies. Z_\mathrm{IT} = Z + \left( \frac{\ 1\ }{ Y } \parallel Z_\mathrm{IT} \right)\ which is also known as its iterative impedance.

Its solution is: Z_\mathrm{ IT } = {Z \over 2} \pm \sqrt { {Z^2 \over 4} + {Z \over Y} }\ For a transmission line, it can be seen as a limiting case of an infinite ladder network with infinitesimal impedance and admittance at a constant ratio. Taking the positive root, this equation simplifies to: \ Z_\mathrm{IT} = \sqrt{ \frac{\ Z\ }{ Y }\ }\ Z_0 = \sqrt{\frac{L}{C}\,}\,.

In particular, does not depend any more upon the frequency. The above expression is wholly real, since the imaginary term has canceled out, implying that is purely resistive. For a lossless line terminated in , there is no loss of current across the line, and so the voltage remains the same along the line.

The lossless line model is a useful approximation for many practical cases, such as low-loss transmission lines and transmission lines with high frequency. For both of these cases, and are much smaller than and , respectively, and can thus be ignored.

The solutions to the long line transmission equations include incident and reflected portions of the voltage and current: \begin{align} V &= \frac{V_r + I_r Z_c}{2} e^{\gamma x} + \frac{V_r - I_r Z_c}{2} e^{-\gamma x} \\[1ex] I &= \frac{V_r/Z_c + I_r}{2} e^{\gamma x} - \frac{V_r/Z_c - I_r}{2} e^{-\gamma x} \end{align} When the line is terminated with its characteristic impedance, the reflected portions of these equations are reduced to 0 and the solutions to the voltage and current along the transmission line are wholly incident. Without a reflection of the wave, the load that is being supplied by the line effectively blends into the line making it appear to be an infinite line.

In a lossless line this implies that the voltage and current remain the same everywhere along the transmission line. Their magnitudes remain constant along the length of the line and are only rotated by a phase angle. \mathrm{SIL} = \frac{{V_\mathrm{LL}}^2}{Z_0} in which is the root mean square (RMS) line-to-line voltage in volts.

Loaded below its SIL, the voltage at the load will be greater than the system voltage. Above it, the load voltage is depressed. The Ferranti effect describes the voltage gain towards the remote end of a very lightly loaded (or open ended) transmission line.

Underground cables normally have a very low characteristic impedance, resulting in an SIL that is typically in excess of the thermal limit of the cable.

Text derived from https://en.wikipedia.org/w/index.php?oldid=1376023653 under CC BY-SA 4.0; modifications have been made.

Provenance

snapshot enwiki-001376023653 · captured 2026-09-21 · ledger · version history

Cite this page as: encyclopegia.org, “Characteristic impedance”, snapshot enwiki-001376023653. https://encyclopegia.org/a/characteristic-impedance

Sources cited in this revision

7 named source(s) extracted from the cited revision. A source with no author is shown by its publication; nothing is invented.