Circulator pump
A circulator pump or circulating pump is a specific type of pump used to circulate gases, liquids, or slurries in a closed circuit with small elevation changes.
≈ 5 min read
Names in other languages
No names in other languages are held for this entry yet.
Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.
A circulator pump or circulating pump is a specific type of pump used to circulate gases, liquids, or slurries in a closed circuit with small elevation changes. They are commonly found circulating water in a hydronic heating or cooling system.
They are specialized in providing a large flow rate rather than providing much head, as they are supposed to only overcome the friction of a piping system, as opposed to a regular centrifugal pump which may need to lift a fluid significantly. Circulator pumps as used in hydronic systems are usually electrically powered centrifugal pumps.
As used in homes, they are often small, sealed, and rated at a fraction of a horsepower, but in commercial applications they range in size up to many horsepower and the electric motor is usually separated from the pump body by some form of mechanical coupling. The sealed units used in home applications often have the motor rotor, pump impeller, and support bearings combined and sealed within the water circuit.
This avoids one of the principal challenges faced by the larger, two-part pumps: maintaining a water-tight seal at the point where the pump drive shaft enters the pump body. Small- to medium-sized circulator pumps are usually supported entirely by the pipe flanges that join them to the rest of the hydronic plumbing. Large pumps are typically pad-mounted.…
A circulator pump or circulating pump is a specific type of pump used to circulate gases, liquids, or slurries in a closed circuit with small elevation changes. They are commonly found circulating water in a hydronic heating or cooling system.
They are specialized in providing a large flow rate rather than providing much head, as they are supposed to only overcome the friction of a piping system, as opposed to a regular centrifugal pump which may need to lift a fluid significantly. Circulator pumps as used in hydronic systems are usually electrically powered centrifugal pumps.
As used in homes, they are often small, sealed, and rated at a fraction of a horsepower, but in commercial applications they range in size up to many horsepower and the electric motor is usually separated from the pump body by some form of mechanical coupling. The sealed units used in home applications often have the motor rotor, pump impeller, and support bearings combined and sealed within the water circuit.
This avoids one of the principal challenges faced by the larger, two-part pumps: maintaining a water-tight seal at the point where the pump drive shaft enters the pump body. Small- to medium-sized circulator pumps are usually supported entirely by the pipe flanges that join them to the rest of the hydronic plumbing. Large pumps are typically pad-mounted.
Pumps that are used solely for closed hydronic systems can be made with cast iron components as the water in the loop will either become de-oxygenated or be treated with chemicals to inhibit corrosion. However, pumps that have a steady stream of oxygenated, potable water flowing through them must be made of more expensive materials such as bronze.
Quantitative measures of function
During the pump operation, there is a drop of the liquid flow in the center of the rotor, causing the inflow of the liquid through the suction port. In the event of an excessive pressure decrease, in some parts of the rotor, the pressure can be lower than the saturation pressure corresponding to the temperature of the pumped liquid, causing the so-called cavitation, i.e. liquid evaporation.
To prevent this, the pressure in the suction port (at the inlet of the pump) should be higher than the saturation pressure corresponding to the liquid temperature by the net positive suction head (NPSH). The following parameters are characteristic for the circulating pumps: capacity Q, pump pressure ∆p (delivery head ∆H), energy consumption P with pump unit efficiency η, impeller rotational speed n, NPSH and sound level L. In practice, the graphical relationship between the values Q, ∆ p(∆H), P and η is used.
These are called the pump curves. They are determined by studies, whose methodology is standardized. These curves are specified when water is pumped with a density of 1000 kg/m3 and kinematic viscosity of 1 mm2/s. When the circulating pump is used for liquids of different density and viscosity, the pump curves have to be recalculated.
These curves are provided in catalogues and in operation and maintenance manuals, however their stroke is the subject of pump manufacturers warranty.
Text derived from https://en.wikipedia.org/w/index.php?oldid=1329664443 under CC BY-SA 4.0; modifications have been made.