CMOS amplifier

Uses your system voice; voice and rate in settings.

Snapshot

≈ 7 min read

Names in other languages

No names in other languages are held for this entry yet.

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

CMOS amplifiers (complementary metal–oxide–semiconductor amplifiers) are ubiquitous analog circuits used in computers, audio power amplifiers, smartphones, cameras, telecommunication systems, biomedical circuits, and many other systems. Their performance impacts the overall specifications of the systems.

They take their name from the use of MOSFETs (metal–oxide–semiconductor field-effect transistors) as opposite to bipolar junction transistors (BJTs). MOSFETs are simpler to fabricate and therefore less expensive than BJT amplifiers, still providing a sufficiently high transconductance to allow the design of very high performance circuits.

In high performance CMOS (complementary metal–oxide–semiconductor) amplifier circuits, transistors are not only used to amplify the signal but are also used as active loads to achieve higher gain and output swing in comparison with resistive loads. CMOS technology was introduced primarily for digital circuit design.

In the last few decades, to improve speed, power consumption, required area, and other aspects of digital integrated circuits (ICs), the feature size of MOSFET transistors has shrunk (minimum channel length of transistors reduces in newer CMOS technologies).…

CMOS amplifiers (complementary metal–oxide–semiconductor amplifiers) are ubiquitous analog circuits used in computers, audio power amplifiers, smartphones, cameras, telecommunication systems, biomedical circuits, and many other systems. Their performance impacts the overall specifications of the systems.

They take their name from the use of MOSFETs (metal–oxide–semiconductor field-effect transistors) as opposite to bipolar junction transistors (BJTs). MOSFETs are simpler to fabricate and therefore less expensive than BJT amplifiers, still providing a sufficiently high transconductance to allow the design of very high performance circuits.

In high performance CMOS (complementary metal–oxide–semiconductor) amplifier circuits, transistors are not only used to amplify the signal but are also used as active loads to achieve higher gain and output swing in comparison with resistive loads. CMOS technology was introduced primarily for digital circuit design.

In the last few decades, to improve speed, power consumption, required area, and other aspects of digital integrated circuits (ICs), the feature size of MOSFET transistors has shrunk (minimum channel length of transistors reduces in newer CMOS technologies). This phenomenon predicted by Gordon Moore in 1975, which is called Moore’s law, and states that in about each 2 years, the number of transistors doubles for the same silicon area of ICs.

Progress in memory circuits design is an interesting example to see how process advancement have affected the required size and their performance in the last decades. In 1956, a 5 MB hard disk drive (HDD) weighed over a ton, while these days having 50000 times more capacity with a weight of several tens of grams is very common.

While digital ICs have benefited from the feature size shrinking, analog CMOS amplifiers have not gained corresponding advantages due to the intrinsic limitations of an analog design—such as the intrinsic gain reduction of short-channel transistors, which affects the overall amplifier gain. Novel techniques that achieve higher gain also create new problems, like amplifier stability for closed-loop applications.

The following addresses both aspects and summarizes different methods to overcome these problems. A v_\text{int} = g_m r_o, where g_m is the transconductance, and r_o is the output resistance of transistor. As a first-order approximation, r_o is directly proportional to the channel length of transistors.

In a single-stage amplifier, one can increase channel length to get higher output resistance and gain as well, but this also increases the parasitic capacitance of transistors, which limits the amplifier bandwidth. The transistor channel length is smaller in modern CMOS technologies, which makes achieving high gain in single-stage amplifiers very challenging.

To achieve high gain, the literature has suggested many techniques. The following sections look at different amplifier topologies and their features. Telescopic, folded cascode (FC), or recycling FC (RFC) are the most common single-stage amplifiers.

All these structures use transistors as active loads to provide higher output resistance (= higher gain) and output swing. A telescopic amplifier provides higher gain (due to higher output resistance) and higher bandwidth (due to smaller non-dominant pole at the cascode node). In contrast, it has limited output swing and difficulty in implementation of unity-gain buffer.

Although FC has lower gain and bandwidth, it can provide a higher output swing, an important advantage in modern CMOS technologies with reduced supply voltage. Also, since the DC voltage of input and output nodes can be the same, it is more suitable for implementation of unity-gain buffer. FC is recently used to implement integrator in a bio-nano sensor application.

Also, it can be used as a stage in multi-stage amplifiers. As an example, FC is used as the input stage of a two-stage amplifier in designing of a potentiostat circuit, which is to measure neuronal activities, or DNA sensing. Also, it can be used to realize transimpedance amplifier (TIA).

TIA can be used in amperometric biosensors to measure current of cells or solutions to define the characteristics of a device under test In the last decade , circuit designers have proposed different modified versions of FC circuit. RFC is one of the modified versions of FC amplifier, which provides higher gain, higher bandwidth, and also higher slew rate in comparison with FC (for the same power consumption).

Recently, RFC amplifier has used in hybrid CMOS–graphene sensor array for subsecond measurement of dopamine. It is used as a low-noise amplifier to implement integrator. In many applications, an amplifier drives a capacitor as a load.

In some applications, like switched capacitor circuits, the value of capacitive load changes in different cycles. Therefore, it affects output node time constant and amplifier frequency response. Stable behavior of amplifier for all possible capacitive loads is necessary, and designer must consider this issue during designing of circuit.

Designer should ensure that phase margin (PM) of the circuit is enough for the worst case. To have proper circuit behavior and time response, designers usually consider a PM of 60 degrees. For higher PM values, the circuit is more stable, but it takes longer for the output voltage to reach its final value.

In telescopic and FC amplifiers, the dominant pole is at the output nodes. Also, there is a non-dominant pole at the cascode node. Since capacitive load connected to output nodes, its value affects the location of the dominant pole.

This figure shows how capacitive load affects the location of dominant pole (\omega_1) and stability. Increasing capacitive load moves the dominant pole toward the origin, and since unity gain frequency (\omega_\text{unity}) is A_v (amplifier gain) times \omega_1, it also moves toward the origin. Therefore, PM increases, which improves stability.

So, if we ensure stability of a circuit for a minimum capacitive load, it remains stable for larger load values. To achieve greater than 60 degrees PM, the non-dominant pole (\omega_2) must be greater than 1.7\,\omega_\text{unity}.

Text derived from https://en.wikipedia.org/w/index.php?oldid=1376909876 under CC BY-SA 4.0; modifications have been made.

Sources cited in this revision

7 named source(s) extracted from the cited revision. A source with no author is shown by its publication; nothing is invented.