Coaxial cable
flexible coaxial cable composed of: Coaxial cable, or coax (pronounced ), is a type of electrical cable consisting of an inner center conductor surrounded by a concentric conducting shield, with the two separated by a dielectric…
≈ 8 min read
Names in other languages
No names in other languages are held for this entry yet.
Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.
flexible coaxial cable composed of: Coaxial cable, or coax (pronounced ), is a type of electrical cable consisting of an inner center conductor surrounded by a concentric conducting shield, with the two separated by a dielectric (insulating material); many coaxial cables also have a protective outer sheath or jacket. The term coaxial refers to the inner conductor and the outer shield sharing a geometric axis.
Coaxial cable is a type of unbalanced transmission line, used to carry high-frequency electrical signals with low losses. It is used in such applications as telephone trunk lines, broadband internet networking cables, high-speed computer data buses, cable television signals, and connecting radio transmitters and receivers to their antennas.
It differs from other shielded cables because the dimensions of the cable and connectors are controlled to give a precise, constant conductor spacing, which is needed for it to function efficiently as a transmission line. showed how coaxial cable could eliminate signal interference between parallel cables. Coaxial cable was used in the first (1858) and following transatlantic cable installations, but its theory was not described until 1880 by English physicist, engineer, and mathematician Oliver Heaviside, who patented the design in that year (British patent No. 1,407).
Dielectric constant \epsilon of the insulator. The dielectric constant is often quoted as the relative dielectric constant \epsilon_\text{r} referred to the dielectric constant \epsilon_0 of free space: \epsilon = \epsilon_\text{r} \epsilon_0.
When the insulator is a mixture of different dielectric materials (e.g., polyethylene foam is a mixture of polyethylene and air), then the term effective dielectric constant \epsilon_\text{eff} is often used. Magnetic permeability \mu of the insulator.
Permeability is often quoted as the relative permeability \mu_\text{r} referred to the permeability \mu_0 of free space: \mu = \mu_\text{r} \mu_0. The relative permeability will almost always be . Shunt capacitance per unit length, in farads per metre: C = \frac{2 \pi \epsilon}{\ln \frac{D}{d}} = \frac{2 \pi \epsilon_0 \epsilon_\text{r}}{\ln \frac{D}{d}}.
Series inductance per unit length, in henries per metre, considering the central conductor to be a thin hollow cylinder (due to skin effect): L = \frac{\mu}{2 \pi} \ln \frac{D}{d} = \frac{\mu_0 \mu_\text{r}}{2 \pi} \ln \frac{D}{d}. Series resistance per unit length, in ohms per metre.
The resistance per unit length is just the resistance of inner conductor and the shield at low frequencies. At higher frequencies, skin effect increases the effective resistance by confining the conduction to a thin layer of each conductor. Shunt conductance per unit length, in siemens per metre.
The shunt conductance is usually very small because insulators with good dielectric properties are used (a very low loss tangent). At high frequencies, a dielectric can have a significant resistive loss. Characteristic impedance in ohms (Ω).
The complex impedance of an infinite length of transmission line is Z_0 = \sqrt{\frac{R + sL}{G + sC}}, where is the resistance per unit length, is the inductance per unit length, is the conductance per unit length of the dielectric, is the capacitance per unit length, and is the frequency. The "per unit length" dimensions cancel out in the impedance formula.
At DC the two reactive terms are zero, so the impedance is real-valued, and is extremely high. It looks like Z_\text{DC} = \sqrt{\frac{R}{G}}. With increasing frequency, the reactive components take effect, and the impedance of the line is complex-valued.
At very low frequencies (audio range, of interest to telephone systems) is typically much smaller than , so the impedance at low frequencies is Z_\text{LF} \approx \sqrt{\frac{R}{sC}}, which has a phase value of −45°. At higher frequencies, the reactive terms usually dominate and , and the cable impedance again becomes real-valued.
That value is , the characteristic impedance of the cable: Z_0 = \sqrt{\frac{sL}{sC}} = \sqrt{\frac{L}{C}}. Assuming that the dielectric properties of the material inside the cable do not vary appreciably over the operating range of the cable, the characteristic impedance is frequency independent above about five times the shield cutoff frequency.
For typical coaxial cables, the shield cutoff frequency is 600 Hz (for RG-6A) to 2,000 Hz (for RG-58C). The parameters and are determined from the ratio of the inner ( ) and outer ( ) diameters and the dielectric constant ( ). The characteristic impedance is given by Z_0 = \frac{1}{2\pi} \sqrt{\frac{\mu}{\epsilon}} \ln \frac{D}{d} \approx \frac{59.96~\Omega}{\sqrt{\epsilon_\text{r}}} \ln \frac{D}{d} \approx \frac{138~\Omega}{\sqrt{\epsilon_\text{r}}} \log_{10} \frac{D}{d}.
Attenuation (loss) per unit length, in decibels per metre. This is dependent on the loss in the dielectric material filling the cable and resistive losses in the centre conductor and outer shield. These losses are frequency-dependent, becoming higher as the frequency increases.
Skin-effect losses in the conductors can be reduced by increasing the diameter of the cable. A cable with twice the diameter has half the skin effect resistance. Ignoring dielectric and other losses, the larger cable would halve the dB/m loss.
In designing a system, engineers consider not only the loss in the cable but also the loss in the connectors. Velocity of propagation, in metres per second. The velocity of propagation depends on the dielectric constant and permeability (which is usually ): v = \frac{1}{\sqrt{\epsilon \mu}} = \frac{c}{\sqrt{\epsilon_\text{r} \mu_\text{r}}}.
Single-mode band. In coaxial cable, the dominant mode (the mode with the lowest cutoff frequency) is the TEM mode, which has a cutoff frequency of zero; it propagates all the way down to DC. The mode with the next lowest cutoff is the TE mode. This mode has one "wave" (two reversals of polarity) in going around the circumference of the cable.
To a good approximation, the condition for the TE mode to propagate is that the wavelength in the dielectric is no longer than the average circumference of the insulator; that is that the frequency is at least f_\text{c} \approx \frac{1}{\pi \left(\frac{D + d}{2}\right) \sqrt{\mu \epsilon}} = \frac{c}{\pi \left(\frac{D + d}{2}\right) \sqrt{\mu_\text{r} \epsilon_\text{r}}}. Hence, the cable is single-mode from DC up to this frequency and might in practice be used up to 90% of this frequency.
Peak voltage. The peak voltage is set by the breakdown voltage of the insulator: V_\text{p} = E_\text{d} \frac{d}{2} \ln \frac{D}{d}, where is the peak voltage, is the insulator breakdown voltage in volts per metre, is the inner diameter in metres, is the outer diameter in metres. The calculated peak voltage is often reduced by a safety factor.
Z_0 = \sqrt{ \frac{R + j\omega L}{G + j\omega C} }. Applying this formula to typical 75-ohm coaxial cable gives impedance across the audio spectrum in the range from ~150 Ω to ~5 kΩ, much higher than nominal. The velocity of propagation also decreases considerably.
Thus coaxial-cable impedances are consistent at RF frequencies but variable across audio frequencies. This effect was manifested when trying to send a plain voice signal across the transatlantic telegraph cable, with poor results.
RG-6 coaxial cable.png | RG-6 coaxial cable RG-142 Coaxial cable.png | RG-142 coaxial cable RG-405 semi-rigid coaxial cable.png | RG-405 semi-rigid coaxial cable High-end-audio-cable-stereovox-HDXV.jpg | High-end coaxial audio cable (S/PDIF) Cables, Radio Frequency, Flexible and Rigid Details Specification MIL-DTL-17H, 19 August 2005 (superseding MIL-C-17G, 9 March 1990). * Brooke Clarke, [http://www.prc68.com/I/Zo.shtml "Transmission Line Zo vs. Frequency"
Text derived from https://en.wikipedia.org/w/index.php?oldid=1376805160 under CC BY-SA 4.0; modifications have been made.