Coke (fuel)
Coke is a grey, hard, and porous coal-based fuel with a high carbon content.
≈ 9 min read
Names in other languages
No names in other languages are held for this entry yet.
Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.
Coke is a grey, hard, and porous coal-based fuel with a high carbon content. It is made by heating coal or petroleum in the absence of air. Coke is an important industrial product, used mainly in the smelting of iron ore, but also as a fuel in stoves and forges.
The unqualified term "coke" usually refers to the product derived from low-ash and low-sulphur bituminous coal by a process called coking. A similar product called petroleum coke, or pet coke, is obtained from crude petroleum in petroleum refineries. Coke may also be formed naturally by geologic processes.
It is the residue of a destructive distillation process.
Industrial coke furnaces
plant, Abercwmboi, Wales, 1976 at Royston, South Yorkshire, in operation discharging glowing coke from one of the bank of ovens on the left in 2013 The industrial production of coke from coal is called coking. The coal is baked in an airless kiln, a coke furnace or coking oven, at temperatures as high as but usually around .
This process vaporises or decomposes organic substances in the coal, driving off water and other volatile and liquid products such as coal gas and coal tar. Coke is the non-volatile residue of the decomposition, the cemented-together carbon and mineral residue of the original coal particles in the form of a hard and somewhat glassy solid.
Additional byproducts of the coking are coal-tar pitch, ammonia ( ), hydrogen sulphide ( ), pyridine, hydrogen cyanide, and carbon-based material. Some facilities have "by-product" coking ovens in which the volatile decomposition products are collected, purified, and separated for use in other industries, as fuel or chemical feedstocks.
Otherwise the volatile byproducts are burned to heat the coking ovens. This is an older method, but is still being used for new construction.
The "hearth" process
The "hearth" process of coke-making, using lump coal, was akin to that of charcoal-burning; instead of a heap of prepared wood, covered with twigs, leaves, and earth, there was a heap of coal, covered with coke dust. The hearth process continued to be used in many areas during the first half of the 19th century, but two events greatly lessened its importance.
These were the invention of the hot blast in iron-smelting and the introduction of the beehive coke oven. The use of a blast of hot air, instead of cold air, in the smelting furnace was first introduced by Neilson in Scotland in 1828. The hearth process of making coke from coal is a very lengthy process.
Beehive coke oven
in Fayette County, Pennsylvania A firebrick chamber shaped like a dome is used, commonly known as a beehive oven. It is typically about wide and high. The roof has a hole for charging the coal or other kindling from the top.
A discharging hole is provided in the circumference of the lower part of the wall. In a coke-oven battery, a number of ovens are built in a row with common walls between neighboring ovens. A battery consisted of a great many ovens, sometimes hundreds, in a row.
Coal is introduced from the top to produce an even layer of about deep. Air is supplied initially, to ignite the coal. Carbonization starts and produces volatile matter, which burns inside the partially closed side door.
Carbonization proceeds from top to bottom and is completed in two to three days. The heat required for the process is supplied by the burning volatile matter, so no by-products are recovered. The exhaust gases are allowed to escape to the atmosphere.
The hot coke is quenched with water, and is discharged manually through the side door. When the oven is used on a continuous basis, the walls and roof retain enough heat to initiate carbonization of the next charge.
When coal was burned in a coke oven, the impurities of the coal that were not driven off as gases accumulated in the oven as slag – effectively a conglomeration of the removed impurities. Since this slag was not the desired product, it was initially just discarded.
Later, however, coke-oven slag was found to be useful, and has since been used as an ingredient in brick-making, mixed cement, granule-covered shingles, and even as a fertilizer.
Occupational safety
People can be exposed to coke oven emissions in the workplace by inhalation, skin contact, or eye contact. For the United States, the Occupational Safety and Health Administration (OSHA) has set the legal limit for coke oven emissions exposure in the workplace as 0.150 mg/m 3 benzene-soluble fraction over an eight-hour workday.
The US National Institute for Occupational Safety and Health (NIOSH) has set a recommended exposure limit (REL) of 0.2 mg/m 3 benzene-soluble fraction over an eight-hour workday.
Uses
Coke can be used as a fuel and as a reducing agent in smelting iron ore in a blast furnace. The carbon monoxide produced by combustion of coke reduces iron oxide (hematite) to produce iron: . Coke is commonly used as fuel for blacksmithing.
Coke was used in Australia in the 1960s and early 1970s for house heating, and was incentivized for home use in the UK (so as to displace coal) after the 1956 Clean Air Act, which was passed in response to the Great Smog of London in 1952. Since smoke-producing constituents are driven off during the coking of coal, coke forms a desirable fuel for stoves and furnaces in which conditions are not suitable for the complete burning of bituminous coal itself.
Coke may be combusted producing little or no smoke, while bituminous coal would produce much smoke. Coke was widely used as a smokeless substitute for coal in domestic heating following the creation of "smokeless zones" in the United Kingdom. Coke may be used to make synthesis gas, a mixture of carbon monoxide and hydrogen.
Syngas; water gas: a mixture of carbon monoxide and hydrogen, made by passing steam over red-hot coke (or any carbon-based char). Hydrocarbonate (gas) is identical, although it emerged in the late eighteenth century as an inhalation therapeutic developed by Thomas Beddoes and James Watt categorized under factitious airs .
Producer gas; wood gas; generator gas; synthetic gas: a mixture of carbon monoxide, hydrogen, and nitrogen, made by passing air over red-hot coke (or any carbon-based char). Coke oven gas generated from coke ovens is similar to syngas with 60% hydrogen by volume. The hydrogen can be extracted from the coke oven gas economically for various uses (including steel production).
In foundry components
Finely-ground bituminous coal, known in this application as sea coal, is a constituent of foundry sand. While the molten metal is in the mould, the coal burns slowly, releasing reducing gases at pressure, and so preventing the metal from penetrating the pores of the sand. It is also contained in "mould wash", a paste or liquid with the same function applied to the mould before casting.
Sea coal can be mixed with the clay lining (the "bod") used for the bottom of a cupola furnace. When heated, the coal decomposes and the bod becomes slightly friable, easing the process of breaking open holes for tapping the molten metal.
Phenolic byproducts
Wastewater from coking is highly toxic and carcinogenic. It contains phenolic, aromatic, heterocyclic, and polycyclic organics, and inorganics including cyanides, sulfides, ammonium, and ammonia. Various methods for its treatment have been studied in recent years. The white rot fungus Phanerochaete chrysosporium can remove up to 80% of phenols from coking waste water.
Properties
of the Great Lakes Steel Corporation, Detroit. Coal tower atop coke ovens. November 1942 Before bituminous coal is used as coking coal, it must meet a set of criteria determined by particular coal assay techniques.
The bulk specific gravity of coke is typically around 0.77. It is highly porous. Both the chemical composition and physical properties are important to the usefulness of coke in blast furnaces.
In terms of composition, low ash and sulphur content are desirable. Other important characteristics are the M10, M25, and M40 test-crush indexes, which convey the strength of coke during transportation into the blast furnaces; depending on the blast furnace's size, finely crushed coke pieces must not be allowed into the furnace because they would impede the flow of gas through the charge of iron and coke.
A related characteristic is the Coke Strength After Reaction (CSR) index; it represents coke's ability to withstand the violent conditions inside the blast furnace before turning into fine particles. Pieces of coke are denoted with the following terminology: "bell coke" (30–80 mm), "nut coke" (10–30 mm), "coke breeze" ( File:Coke-Ovens---Cokedale-CO.jpg|Coal coking ovens at Cokedale, Colorado, supplied steel mills in Pueblo, CO File:Cherry Valley Coke Ovens 3.jpg|The 200 Cherry Valley Coke Ovens built around 1866 File:Dunlap-coke-ovens-tn2.jpg|Dunlap coke ovens File:Minersville Coke Ovens.jpg|Minersville Coke Ovens File:Old coke ovens, Redstone, CO.jpg|Redstone Coke Oven Historic District File:SydneyCokeOvenGeneralViewCa1900.jpg|Sydney Tar Ponds
See also
Charcoal, made from wood rather than coal Coking factory History of manufactured gas List of CO2 emitted per million Btu of energy from various fuels Petroleum coke Pyrolysis Sydney Tar Ponds, environmental damage caused by coke oven Tar
Text derived from https://en.wikipedia.org/w/index.php?oldid=1375077185 under CC BY-SA 4.0; modifications have been made.