Commodore 1571
≈ 8 min read
Names in other languages
No names in other languages are held for this entry yet.
Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.
The Commodore 1571 is Commodore's high-end 5¼" floppy disk drive, announced in the summer of 1985. With its double-sided drive mechanism, it has the ability to use double-sided, double-density (DS/DD) floppy disks, storing a total of 360 kB per floppy. It also implemented a "burst mode" that improved transfer speeds, helping address the very slow performance of previous Commodore drives. Earlier Commodore drives used a custom group coded recording format that stored 170 kB per side of a disk.
This made it fairly competitive in terms of storage, but limited it to only reading and writing disks from other Commodore machines. The 1571 was designed to partner with the new Commodore 128 (C128), which introduced support for CP/M. Adding double-density MFM encoding allowed the drive to read and write contemporary CP/M disks (and many others). In contrast to its single-sided predecessors, the 15411 and the briefly-available 1570, the 1571 can use both sides of the disk at the same time.
Previously, users could only use the second side by manually flipping them over.…
The Commodore 1571 is Commodore's high-end 5¼" floppy disk drive, announced in the summer of 1985. With its double-sided drive mechanism, it has the ability to use double-sided, double-density (DS/DD) floppy disks, storing a total of 360 kB per floppy. It also implemented a "burst mode" that improved transfer speeds, helping address the very slow performance of previous Commodore drives. Earlier Commodore drives used a custom group coded recording format that stored 170 kB per side of a disk.
This made it fairly competitive in terms of storage, but limited it to only reading and writing disks from other Commodore machines. The 1571 was designed to partner with the new Commodore 128 (C128), which introduced support for CP/M. Adding double-density MFM encoding allowed the drive to read and write contemporary CP/M disks (and many others). In contrast to its single-sided predecessors, the 1541 and the briefly-available 1570, the 1571 can use both sides of the disk at the same time.
Previously, users could only use the second side by manually flipping them over. Because flipping the disk also reverses the direction of rotation, the two methods are not interchangeable; disks which had their back side created in a 1541 by flipping them over would have to be flipped in the 1571 too, and the back side of disks written in a 1571 using the native support for two-sided operation could not be read in a 1541. The 1571 was released to match the Commodore 128, both design-wise and feature-wise.
It was announced in the summer of 1985, at the same time as the C128, and became available in quantity later that year. The later C128D has a 1571 drive built into the system unit. A double-sided disk on the 1571 has a capacity of 340 kB (70 tracks, 1,360 disk blocks of 256 bytes each); 8 kB are reserved for system use (directory and block availability information) and, under of each block serve as pointers to the next logical block, = 337,312 B or about are available for user data.
(However, with a program organizing disk storage on its own, all space could be used, e.g. for data disks.) The 1571 was designed to accommodate the C128's "burst" mode for faster disk access, however the drive cannot use it if connected to older Commodore machines. This mode replaced the slow bit-banging serial routines of the 1541 with a true serial shift register implemented in hardware, thus dramatically increasing the drive speed.
Although this originally had been planned when Commodore first switched from the parallel IEEE-488 interface to the CBM-488 custom serial interface, hardware bugs in the VIC-20's 6522 VIA shift register prevented it from working properly. When connected to a C128, the 1571 defaults to double-sided mode, which allowsd the drive to read its own 340k disks as well as single-sided 170 kB 1541 disks. If the C128 is switched into C64 mode by typing GO 64 from BASIC, the 1571 stays in double-sided mode.
If C64 mode is activated by holding down the C= key on power-up, the drive automatically switches to single-sided mode, in which case it is unable to read 340 kB disks (also the default if a 1571 is used with a C64, Plus/4, VIC-20, or PET). A manual command can also be issued from BASIC to switch the 1571 between single and double sided mode.
There is also an undocumented command which allows the user to independently control either of the read/write heads of the 1571, making it possible to format both sides of a diskette separate from each other, however the resultant disk cannot be read in a 1541 as it would be spinning in reverse direction when flipped upside down. In the same vein, "flippy" disks created with a 1541 cannot be read on a 1571 with this feature; they must be inserted upside down.
The 1571 is not 100% low-level compatible with the 1541; however, this isn't a problem except in some software that uses advanced copy protections such as the RapidLok system found on MicroProse and Accolade games. The 1571 is noticeably quieter than its predecessor and runs cooler, even though, like the 1541, it had an internal power supply (later Commodore drives, like the 1541-II and the 3½" 1581, came with external power supplies).
The 1541-II/1581 power supply makes mention of a 1571-II, hinting that Commodore may have intended to release a version of the 1571 with an external power supply. However, no 1571-IIs are known to exist. The embedded operating system in the 1571 was an improvement over the Early 1571s had a bug in the ROM-based disk operating system that caused relative files to corrupt if they occupied both sides of the disk.
A version 2 ROM was released, but though it cured the initial bug, it introduced some minor quirks of its own – particularly with the 1541 emulation. Curiously, it was also identified as V3.0. As with the 1541, Commodore initially could not meet demand for the 1571, and that lack of availability and the drive's relatively high price (about US$300) presented an opportunity for clones. Two 1571 clones appeared, one from Oceanic and one from Blue Chip, but legal action from Commodore quickly drove them from the market.
Commodore announced at the 1985 Consumer Electronics Show a dual-drive version of the 1571, to be called the Commodore 1572, but quickly canceled it, reportedly due to technical difficulties with the 1572 DOS. It would have had four times as much RAM as the 1571 (8 kB), and twice as much ROM (64 kB). The 1572 would have allowed for fast disk backups of non-copy-protected media, much like the old 4040, 8050, and 8250 dual drives.
The 1571 built into the European plastic-case C128D computer is electronically identical to the stand-alone version, but 1571 version integrated into the later metal-case C128D (often called C128 DCR, for D Cost-Reduced) differs a lot from the stand-alone 1571. It includes a newer DOS, version 3.1, replaces the MOS Technology CIA interface chip, of which only a few features were used by the 1571 DOS, with a very much simplified chip called 5710, and has some compatibility issues with the stand-alone drive.
Because this internal 1571 does not have an unused 8-bit input/output port on any chip, unlike most other Commodore drives, it is not possible to install a parallel cable in this drive, such as that used by SpeedDOS, DolphinDOS and some other fast third-party Commodore DOS replacements.
Further reading
Text derived from https://en.wikipedia.org/w/index.php?oldid=1372473010 under CC BY-SA 4.0; modifications have been made.
References
- ↩Wikipedia “Commodore 1571” release date (×1) · confidence 0.95 revision URL