Common base
≈ 5 min read
Names in other languages
No names in other languages are held for this entry yet.
Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.
details) In electronics, a common-base (also known as grounded-base) amplifier is one of three basic single-stage bipolar junction transistor (BJT) amplifier topologies, typically used as a current buffer or voltage amplifier. In this circuit the emitter terminal of the transistor serves as the input, the collector as the output, and the base is connected to ground, or "common", hence its name. The analogous field-effect transistor circuit is the common-gate amplifier.
Impact
details) In electronics, a common-base (also known as grounded-base) amplifier is one of three basic single-stage bipolar junction transistor (BJT) amplifier topologies, typically used as a current buffer or voltage amplifier. In this circuit the emitter terminal of the transistor serves as the input, the collector as the output, and the base is connected to ground, or "common", hence its name. The analogous field-effect transistor circuit is the common-gate amplifier.
R_\text{in} = r_\text{E} = \frac{V_\text{T}}{I_\text{E}}, where V T is the thermal voltage, and I E is the DC emitter current. For example, for V T = 26 mV and I E = 10 mA, rather typical values, R in = 2.6 Ω. If I E is reduced to increase R in , there are other consequences like lower transconductance, higher output resistance and lower β that also must be considered. A practical solution to this low-input-impedance problem is to place a common-emitter stage at the input to form a cascode amplifier.
Evidence and sources
Because the input impedance is so low, most signal sources have larger source impedance than the common-base amplifier R in . The consequence is that the source delivers a current to the input rather than a voltage, even if it is a voltage source. (According to Norton's theorem, this current is approximately i in = v S / R S ). If the output signal also is a current, the amplifier is a current buffer and delivers the same current as is input.
If the output is taken as a voltage, the amplifier is a transresistance amplifier and delivers a voltage dependent on the load impedance, for example v out = i in R L for a resistor load R L much smaller in value than the amplifier output resistance R out . That is, the voltage gain in this case (explained in more detail below) is v_\text{out} = i_\text{in} R_\text{L} = v_\text{s} \frac{R_\text{L}}{R_\text{S}} \Rightarrow A_v = \frac{v_\text{out}}{v_\text{S}} = \frac{R_\text{L}}{R_\text{S}}.
Note that for source impedances such that R S ≫ r E the output impedance approaches R out = R C || [g m (r π || R S ) r O ]. For the special case of very low-impedance sources, the common-base amplifier does work as a voltage amplifier, one of the examples discussed below. In this case (explained in more detail below), when R S ≪ r E and R L ≪ R out , the voltage gain becomes A_\text{v} = \frac{v_\text{out}}{v_\text{S}} = \frac{R_\text{L}}{r_\text{E}} \approx g_\text{m} R_\text{L}, where g m = I C / V T is the transconductance.
Notice that for low source impedance, R out = r O || R C . The inclusion of r O in the hybrid-pi model predicts reverse transmission from the amplifiers output to its input, that is the amplifier is bilateral. One consequence of this is that the input/output impedance is affected by the load/source termination impedance, hence, for example, the output resistance R out may vary over the range r O || R C ≤ R out ≤ (β + 1) r O || R C , depending on the source resistance R S .
The amplifier can be approximated as unilateral when neglect of r O is accurate (valid for low gains and low to moderate load resistances), simplifying the analysis. This approximation often is made in discrete designs, but may be less accurate in RF circuits, and in integrated-circuit designs, where active loads normally are used. The output resistance is large, at least R C || r O , the value which arises with low source impedance (R S ≪ r E ).
A large output resistance is undesirable in a voltage amplifier, as it leads to poor voltage division at the output. Nonetheless, the voltage gain is appreciable even for small loads: according to the table, with R S = r E the gain is A v = g m R L / 2. For larger source impedances, the gain is determined by the resistor ratio R L / R S , and not by the transistor properties, which can be an advantage where insensitivity to temperature or transistor variations is important.
An alternative to the use of the hybrid-pi model for these calculations is a general technique based upon two-port networks. For example, in an application like this one where voltage is the output, a g-equivalent two-port could be selected for simplicity, as it uses a voltage amplifier in the output port. For R S values in the vicinity of r E the amplifier is transitional between voltage amplifier and current buffer. For R S ≫ r E the driver representation as a Thévenin source should be replaced by representation with a Norton source.
The common base circuit stops behaving like a voltage amplifier and behaves like a current follower, as discussed next.
Text derived from https://en.wikipedia.org/w/index.php?oldid=1321597196 under CC BY-SA 4.0; modifications have been made.