Compressive strength

Uses your system voice; voice and rate in settings.

Snapshot

≈ 7 min read

Names in other languages

No names in other languages are held for this entry yet.

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

In mechanics, compressive strength (or compression strength) is the capacity of a material or structure to withstand loads tending to reduce size (compression). It is opposed to tensile strength, which withstands loads tending to elongate, resisting tension (being pulled apart). In the study of strength of materials, compressive strength, tensile strength, and shear strength can be analyzed independently.

How it works

Some materials fracture at their compressive strength limit; others deform irreversibly, so a given amount of deformation may be considered as the limit for compressive load. Compressive strength is a key value for design of structures. Compressive strength is often measured on a universal testing machine. Measurements of compressive strength are affected by the specific test method and conditions of measurement. Compressive strengths are usually reported in relationship to a specific technical standard.

Evidence and sources

In mechanics, compressive strength (or compression strength) is the capacity of a material or structure to withstand loads tending to reduce size (compression). It is opposed to tensile strength, which withstands loads tending to elongate, resisting tension (being pulled apart). In the study of strength of materials, compressive strength, tensile strength, and shear strength can be analyzed independently.

Some materials fracture at their compressive strength limit; others deform irreversibly, so a given amount of deformation may be considered as the limit for compressive load. Compressive strength is a key value for design of structures. Compressive strength is often measured on a universal testing machine. Measurements of compressive strength are affected by the specific test method and conditions of measurement. Compressive strengths are usually reported in relationship to a specific technical standard.

The compressive strength of the material corresponds to the stress at the red point shown on the curve. In a compression test, there is a linear region where the material follows Hooke's law. Hence, for this region, \sigma = E\varepsilon, where, this time, refers to the Young's modulus for compression. In this region, the material deforms elastically and returns to its original length when the stress is removed. This linear region terminates at what is known as the yield point.

Above this point the material behaves plastically and will not return to its original length once the load is removed. There is a difference between the engineering stress and the true stress. By its basic definition the uniaxial stress is given by: \acute\sigma = \frac{F}{A}, where is load applied [N] and is area [m 2 ]. As stated, the area of the specimen varies on compression. In reality therefore the area is some function of the applied load i.e. . Indeed, stress is defined as the force divided by the area at the start of the experiment.

This is known as the engineering stress, and is defined by \sigma_e = \frac{F}{A_0}, where is the original specimen area [m 2 ]. Correspondingly, the engineering strain is defined by \varepsilon_e = \frac{l -l_0}{l_0}, where is the current specimen length [m] and is the original specimen length [m].

True strain, also known as logarithmic strain or natural strain, provides a more accurate measure of large deformations, such as in materials like ductile metals \acute \epsilon = \ln (l/l_o)=ln(1+\epsilon_e) The compressive strength therefore corresponds to the point on the engineering stress–strain curve \left(\varepsilon_e^*, \sigma_e^*\right) defined by \sigma_e^* = \frac{F^*}{A_0} \varepsilon_e^* = \frac{l^* - l_0}{l_0}, where is the load applied just before crushing and is the specimen length just before crushing.

When a uniaxial compressive load is applied to an object it will become shorter and spread laterally so its original cross sectional area ( A_o ) increases to the loaded area ( A ). Thus the true stress ( \acute\sigma = F/A ) deviates from engineering stress ( \sigma_e=F/A_o ). Tests that measure the engineering stress at the point of failure in a material are often sufficient for many routine applications, such as quality control in concrete production.

However, determining the true stress in materials under compressive loads is important for research focused on the properties on new materials and their processing. The geometry of test specimens and friction can significantly influence the results of compressive stress tests. Friction at the contact points between the testing machine and the specimen can restrict the lateral expansion at its ends (also known as 'barreling') leading to non-uniform stress distribution. This is discussed in section on contact with friction.

With a compressive load on a test specimen it will become shorter and spread laterally so its cross sectional area increases and the true compressive stress is \acute{\sigma} =F/A and the engineering stress is {\sigma_e} =F/A_o The cross sectional area ( A ) and consequently the stress ( \acute\sigma ) are uniform along the length of the specimen because there are no external lateral constraints. This condition represents an ideal test condition.

For all practical purposes the volume of a high bulk modulus material (e.g. solid metals) is not changed by uniaxial compression. So A l=A_o l_o Using the strain equation from above A=A_o/(1+\epsilon_e) and \acute{\sigma} = \sigma_e(1+\epsilon_e) Note that compressive strain is negative, so the true stress ( \acute\sigma ) is less than the engineering stress ( \sigma_e ). The true strain ( \acute \epsilon ) can be used in these formulas instead of engineering strain ( \epsilon_e ) when the deformation is large.

Round test specimens made from ductile materials with a high bulk modulus, such as metals, tend to form a barrel shape under axial compressive loading due to frictional contact at the ends.

For this case the equivalent true compressive stress for this condition can be calculated using \acute\sigma= C \sigma_a where C= {(1-2 R/d_2) \ln(1-d_2/(2R))}^{-1} R= (l^2+(d_2-d_1)^2)/ (4(d_2-d_1)) \sigma_a=4F/(\pi d_2^2) l is the loaded length of the test specimen, d_1 is the loaded diameter of the test specimen at its ends, and d_2 is the maximum loaded diameter of the test specimen. Note that if there is frictionless contact between the ends of the specimen and the test machine, the bulge radius becomes infinite ( R=\infty ) and C=1 .

Impact

In this case, the formulas yield the same result as \acute{\sigma} = \sigma_e(1+\epsilon_e) because \sigma_a changes according to the ratio (d_o/d_2)^2 . The parameters ( F, d_1, d_2 ,l ) obtained from a test result can be used with these formulas to calculate the equivalent true stress \acute\sigma at failure. The graph of specimen shape effect shows how the ratio of true stress to engineering stress (σ´/σ e ) varies with the aspect ratio of the test specimen ( d_o/l_o ).

The curves were calculated using the formulas provided above, based on the specific values presented in the table for specimen shape effect calculations. For the curves where end restraint is applied to the specimens, they are assumed to be fully laterally restrained, meaning that the coefficient of friction at the contact points between the specimen and the testing machine is greater than or equal to one (μ ⩾ 1).

As shown in the graph, as the relative length of the specimen increases ( d_o/l_o\rightarrow0 ), the ratio of true to engineering stress ( \acute\sigma/ \sigma_e ) approaches the value corresponding to frictionless contact between the specimen and the machine, which is the ideal test condition.

Text derived from https://en.wikipedia.org/w/index.php?oldid=1366678192 under CC BY-SA 4.0; modifications have been made.

Sources cited in this revision

7 named source(s) extracted from the cited revision. A source with no author is shown by its publication; nothing is invented.