Computational methods for free surface flow

In physics, a free surface flow is the surface of a fluid flowing that is subjected to both zero perpendicular normal stress and parallel shear stress.

Uses your system voice; voice and rate in settings.

≈ 5 min read

Cite, export and learn8 citation formats · 8 exports · lesson and quiz

Names in other languages

No names in other languages are held for this entry yet.

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

In physics, a free surface flow is the surface of a fluid flowing that is subjected to both zero perpendicular normal stress and parallel shear stress. This can be the boundary between two homogeneous fluids, like water in an open container and the air in the Earth's atmosphere that form a boundary at the open face of the container.

Computation of free surfaces is complex because of the continuous change in the location of the boundary layer. Conventional methods of computation are insufficient for such analysis. Therefore, special methods are developed for the computation of free surface flows.

[(v - v_b)\cdot n]_{fs} = 0, or \dot{m}_{fs} = 0 where the subscript \Box_{fs} stands for free surface. This implies that the normal component of the velocity of the fluid at the surface is equal to the normal component of the velocity of the free surface.

(n\cdot T)_l \cdot n + \sigma K = -(n\cdot T)_g \cdot n, (n\cdot T)_l \cdot t - \frac{\partial \sigma}{\partial t} = (n\cdot T)_g \cdot t, (n\cdot T)_l \cdot s - \frac{\partial \sigma}{\partial s} = (n \cdot T)_g \cdot s, Here σ is the surface tension, n, t and s are unit vectors in a local orthogonal coordinate system (n,t,s) at the free surface (n is outward normal to the free surface while the other two lie in the tangential plane and are mutually orthogonal). The indices l and g denote liquid and gas, respectively and K is the curvature of the free surface.

K = \frac{1}{R_t} + \frac{1}{R_s} with R t and R s being radii of curvature along coordinates t and s. The surface tension σ is force per unit length of a surface element and acts tangential to the free surface. f_\sigma = \sigma \ dl For an infinitesimally small surface element dS, the tangential components of the surface tension forces cancel out when σ = constant, and the normal component can be expressed as a local force that results in a pressure jump across the surface. Z = H(x,y,t) This gives the kinematic boundary condition a new form: \dfrac{\partial H}{\partial t} =u_z-u_x \dfrac{\partial H}{\partial x}-u_y\dfrac{\partial H}{\partial y} This equation can be integrated and the fluid velocity at free surface can be obtained either by extrapolation from the interior or by using dynamic boundary condition.

For the calculation of flow, FV method is widely used. The steps for a fully conservative FV method of this type are: momentum equation is solved to obtain velocity u i * at the current free surface using specified pressure. Local mass conservation is enforced in each CV by solving a pressure-correction equation.

Mass is conserved both globally and locally, but velocity-correction is produced at free surface giving a non-zero mass flux. Position of free surface is corrected to compensate for the non-zero mass flux with the volume flux due to the movement of the each free-surface cell face by enforcing the kinematic boundary conditions.

Iterate until no further correction is needed, satisfying the continuity and momentum equations. Advance to the next time step. The main problem with the algorithm in this procedure is that there is only one equation for one cell but large number of grid nodes moving.

To avoid instability and wave reflection, the method is modified as follows: From the previous steps, we can calculate the volume of fluid to be flowed in or out of the CV to have mass conservation. To obtain the coordinates of CV vertices at free surface, we have more unknowns and less equations due to single volumetric flow rate for each cell.

Hence the CVs are defined by the cell face centers rather than vertices and vertices are obtained by interpolation. This gives a tridiagonal system for 2D and can be solved using TDMA method.

For 3D, the system is block tridiagonal and is best solved by one of the iterative solvers. + div(cv) = 0 where c is the fraction of control volume filled. c=1 for completely filled and c = 0 for completely empty control volumes. So in total, for VOF method, one has to solve three forms of equations, conservation equations for mass, conservation equations for momentum, equation for filled fraction for each control volume.

NOTE: IN INCOMPRESSIBLE FLOWS, ABOVE EQUATION GIVES SAME RESULTS WITH c AND 1 - c MAKING THE ENFORCEMENT OF MASS CONSERVATION A MUST. Since the higher order schemes are preferred over lower order schemes to prevent artificial mixing of the two fluids, it is important to prevent the overshoots and undershoots due to the condition 0 ≤ c ≤ 1.

For such problems, modifications were made to MAC and VOF schemes.

Text derived from https://en.wikipedia.org/w/index.php?oldid=1281488672 under CC BY-SA 4.0; modifications have been made.

Provenance

snapshot enwiki-001281488672 · captured 2025-03-20 · ledger · version history

Cite this page as: encyclopegia.org, “Computational methods for free surface flow”, snapshot enwiki-001281488672. https://encyclopegia.org/a/computational-methods-for-free-surface-flow

Sources cited in this revision

1 named source(s) extracted from the cited revision. A source with no author is shown by its publication; nothing is invented.