Crystal oscillator

A crystal oscillator is an electronic oscillator circuit that uses a piezoelectric crystal as a frequency-selective element.

Uses your system voice; voice and rate in settings.

≈ 22 min read

Cite, export and learn8 citation formats · 8 exports · lesson and quiz

Names in other languages

No names in other languages are held for this entry yet.

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

A crystal oscillator is an electronic oscillator circuit that uses a piezoelectric crystal as a frequency-selective element. The oscillator frequency is often used to keep track of time, as in quartz wristwatches, to provide a stable clock signal for digital integrated circuits, and to stabilize frequencies for radio transmitters and receivers.

The most common type of piezoelectric resonator used is a quartz crystal, so oscillator circuits incorporating them became known as crystal oscillators. However, other piezoelectric materials including polycrystalline ceramics are used in similar circuits.

A crystal oscillator relies on the slight change in shape of a quartz crystal under an electric field, a property known as inverse piezoelectricity. A voltage applied to the electrodes on the crystal causes it to change shape; when the voltage is removed, the crystal generates a small voltage as it elastically returns to its original shape.

The quartz oscillates at a stable resonant frequency (relative to other low-priced oscillators) with frequency accuracy measured in parts per million (ppm). It behaves like an RLC circuit, but with a much higher Q factor (lower energy loss on each cycle of oscillation and higher frequency selectivity) than can be reliably achieved with discrete capacitors (C) and inductors (L), which suffer from parasitic resistance (R). Once a quartz crystal is adjusted to a particular frequency (which is affected by the mass of electrodes attached to the crystal, the orientation of the crystal, temperature and other factors), it maintains that frequency with high stability.

Quartz crystals are manufactured for frequencies from a few tens of kilohertz to hundreds of megahertz. As of 2003, around two billion crystals were manufactured annually. Most are used for consumer devices such as wristwatches, clocks, radios, computers, and cellphones.

However, in applications where small size and weight is needed crystals can be replaced by thin-film bulk acoustic resonators, specifically if ultra-high frequency (more than roughly 1.5 GHz) resonance is needed. Quartz crystals are also found inside test and measurement equipment, such as counters, signal generators, and oscilloscopes.

Terminology

A crystal oscillator is an electric oscillator type circuit that uses a piezoelectric resonator, a crystal, as its frequency-determining element. Crystal is the common term used in electronics for the frequency-determining component, a wafer of quartz crystal or ceramic with electrodes connected to it. A more accurate term for "crystal" is piezoelectric resonator.

Crystals are also used in other types of electronic circuits, such as crystal filters. Piezoelectric resonators are sold as separate components for use in crystal oscillator circuits. They are also often incorporated in a single package with the crystal oscillator circuit.

History

Piezoelectricity was discovered by Jacques and Pierre Curie in 1880. Paul Langevin first investigated quartz resonators for use in sonar during World War I. The first crystal-controlled oscillator, using a crystal of Rochelle salt, was built in 1917 and patented in 1918 by Alexander M. Nicolson at Western Electric, although his priority was disputed by Walter Guyton Cady.

Cady built the first quartz crystal oscillator in 1921. Other early innovators in quartz crystal oscillators include G. W. Pierce and Louis Essen. Quartz crystal oscillators were developed for high-stability frequency references during the 1920s and 1930s.

Prior to crystals, radio stations controlled their frequency with tuned circuits, which could easily drift off frequency by 3–4 kHz. Since broadcast stations were assigned frequencies only 10 kHz (Americas) or 9 kHz (elsewhere) apart, interference between adjacent stations due to frequency drift was a common problem.

In 1925, Westinghouse installed a crystal oscillator in its flagship station KDKA, and by 1926, quartz crystals were used to control the frequency of many broadcasting stations and were popular with amateur radio operators. In 1928, Warren Marrison of Bell Laboratories developed the first quartz-crystal clock.

With accuracies of up to 1 second in 30 years (30 ms/y, or 0.95 ns/s), quartz clocks replaced precision pendulum clocks as the world's most accurate timekeepers until atomic clocks were developed in the 1950s. Using the early work at Bell Laboratories, American Telephone and Telegraph Company (AT&T) eventually established their Frequency Control Products division, later spun off and known today as Vectron International.

In 1933, Issac Koga of the Tokyo Institute of Technology reported the R1-cut quartz plate, a temperature-insensitive orientation with a near-zero frequency-temperature coefficient. Koga-cut crystals were first used in radio transmitters and later in clocks, and the work was recognized as an IEEE Milestone in 2017.

A number of firms started producing quartz crystals for electronic use during this time. Using what are now considered primitive methods, about 100,000 crystal units were produced in the United States during 1939. Through World War II crystals were made from natural quartz crystal, virtually all from Brazil.

Shortages of crystals during the war caused by the demand for accurate frequency control of military and naval radios and radars spurred postwar research into culturing synthetic quartz, and by 1950 a hydrothermal process for growing quartz crystals on a commercial scale was developed at Bell Laboratories. By the 1970s virtually all crystals used in electronics were synthetic.

In 1968, Juergen Staudte invented a photolithographic process for manufacturing quartz crystal oscillators while working at North American Aviation (now Rockwell) that allowed them to be made small enough for portable products like watches. Although crystal oscillators still most commonly use quartz crystals, devices using other materials are becoming more common, such as ceramic resonators.

Principle

A crystal is a solid in which the constituent atoms, molecules, or ions are packed in a regularly ordered, repeating pattern extending in all three spatial dimensions. Almost any object made of an elastic material could be used like a crystal, with appropriate transducers, since all objects have natural resonant frequencies of vibration.

For example, steel is very elastic and has a high speed of sound. It was often used in mechanical filters before quartz. The resonant frequency depends on size, shape, elasticity, and the speed of sound in the material.

High-frequency crystals are typically cut in the shape of a simple rectangle or circular disk. Low-frequency crystals, such as those used in digital watches, are typically cut in the shape of a tuning fork. For applications not needing very precise timing, a low-cost ceramic resonator is often used in place of a quartz crystal.

When a crystal of quartz is properly cut and mounted, it can be made to distort in an electric field by applying a voltage to an electrode near or on the crystal. This property is known as inverse piezoelectricity. When the field is removed, the quartz generates an electric field as it returns to its previous shape, and this can generate a voltage.

The result is that a quartz crystal behaves like an RLC circuit, composed of an inductor, capacitor and resistor, with a precise resonant frequency. Quartz has the further advantage that its elastic constants and its size change in such a way that the frequency dependence on temperature can be very low.

The specific characteristics depend on the mode of vibration and the angle at which the quartz is cut (relative to its crystallographic axes). Therefore, the resonant frequency of the plate, which depends on its size, does not change much. This means that a quartz clock, filter or oscillator remains accurate.

For critical applications the quartz oscillator is mounted in a temperature-controlled container, called a crystal oven, and can also be mounted on shock absorbers to prevent perturbation by external mechanical vibrations.

Electrical model

A quartz crystal can be modeled as an electrical network with low-impedance (series) and high-impedance (parallel) resonance points spaced closely together. Mathematically, using the Laplace transform, the impedance of this network can be written as: Z(s) = \left( {\frac{1}{s\cdot C_1}+s\cdot L_1+R_1} \right) \left\| \left( {\frac{1}{s\cdot C_0}} \right) \right. , or \begin{align} Z(s) &= \frac{s^2 + s\frac{R_1}{L_1} + {\omega_\mathrm{s}}^2}{\left(s \cdot C_0\right)\left[s^2 + s\frac{R_1}{L_1} + {\omega_\mathrm{p}}^2\right]} \\[2pt] \Rightarrow \omega_\mathrm{s} &= \frac{1}{\sqrt{L_1 \cdot C_1}}, \quad \omega_\mathrm{p} where s is the complex frequency ( s=j\omega ), \omega_\mathrm{s} is the series resonant angular frequency, and \omega_\mathrm{p} is the parallel resonant angular frequency.

Adding capacitance across a crystal causes the (parallel) resonant frequency to decrease. Adding inductance across a crystal causes the (parallel) resonant frequency to increase. These effects can be used to adjust the frequency at which a crystal oscillates.

Crystal manufacturers normally cut and trim their crystals to have a specified resonant frequency with a known "load" capacitance added to the crystal. For example, a crystal intended for a 6 pF load has its specified parallel resonant frequency when a 6.0 pF capacitor is placed across it. Without the load capacitance, the resonant frequency is higher.

Resonance modes

A quartz crystal provides both series and parallel resonance. The series resonance is a few kilohertz lower than the parallel one.

Crystals below 30 MHz are generally operated between series and parallel resonance, which means that the crystal appears as an inductive reactance in operation, this inductance forming a parallel resonant circuit with externally connected parallel capacitance. Any small additional capacitance in parallel with the crystal pulls the frequency lower.

Moreover, the effective inductive reactance of the crystal can be reduced by adding a capacitor in series with the crystal. This latter technique can provide a useful method of trimming the oscillatory frequency within a narrow range; in this case inserting a capacitor in series with the crystal raises the frequency of oscillation.

For a crystal to operate at its specified frequency, the electronic circuit has to be exactly that specified by the crystal manufacturer. Note that these points imply a subtlety concerning crystal oscillators in this frequency range: the crystal does not usually oscillate at precisely either of its resonant frequencies.

Crystals above 30 MHz (up to >200 MHz) are generally operated at series resonance where the impedance appears at its minimum and equal to the series resistance. For these crystals the series resistance is specified ( f = f_0\left[1 - 0.04~\text{ppm}/^\circ\text{C}^2 \cdot (T - T_0)^2\right].

In a real application, this means that a clock built using a regular 32 kHz tuning-fork crystal keeps good time at room temperature, but loses 2 minutes per year (3.8 ppm) at ±10°C (±18°F) (above or below) room temperature and loses 8 minutes per year (15.21 ppm) at ±20°C (±36°F) (above or below) room temperature due to the quartz crystal. Different cuts of crystals behave quite differently with temperature; they have differently shaped curves for how they respond to changes in temperature, and very different optimal temperatures.

For example, SC cut crystals have a optimal temperature at around , and are intended to be used in a temperature-controlled housing which maintains that temperature internally for the crystal, in order to increase stability of the crystal's frequency by mitigating changes in temperature of the surrounding environment.

Crystal oscillator circuits

The crystal oscillator circuit sustains oscillation by taking a voltage signal from the quartz resonator, amplifying it, and feeding it back to the resonator. The rate of expansion and contraction of the quartz is the resonant frequency, and is determined by the cut and size of the crystal.

When the energy of the generated output frequencies matches the losses in the circuit, an oscillation can be sustained. An oscillator crystal has two electrically conductive plates, with a slice or tuning fork of quartz crystal sandwiched between them.

During startup, the controlling circuit places the crystal into an unstable equilibrium, and due to the positive feedback in the system, any tiny fraction of noise is amplified, ramping up the oscillation. The crystal resonator can also be seen as a highly frequency-selective filter in this system: it only passes a very narrow subband of frequencies around the resonant one, attenuating everything else.

Eventually, only the resonant frequency is active. As the oscillator amplifies the signals coming out of the crystal, the signals in the crystal's frequency band becomes stronger, eventually dominating the output of the oscillator. The narrow resonance band of the quartz crystal filters out the unwanted frequencies.

The output frequency of a quartz oscillator can be either that of the fundamental resonance or of a multiple of that resonance, called a harmonic frequency. Harmonics are an exact integer multiple of the fundamental frequency.

But, like many other mechanical resonators, crystals exhibit several modes of oscillation, usually at approximately odd integer multiples of the fundamental frequency. These are termed "overtone modes", and oscillator circuits can be designed to excite them.

The overtone modes are at frequencies which are approximate, but not exact odd integer multiples of that of the fundamental mode, and overtone frequencies are therefore not exact harmonics of the fundamental. High frequency crystals are often designed to operate at third, fifth, or seventh overtones.

Manufacturers have difficulty producing crystals thin enough to produce fundamental frequencies over 30 MHz. To produce higher frequencies, manufacturers make overtone crystals tuned to put the 3rd, 5th, or 7th overtone at the desired frequency, because they are thicker and therefore easier to manufacture than a fundamental crystal that would produce the same frequency—although exciting the desired overtone frequency requires a slightly more complicated oscillator circuit.

A fundamental crystal oscillator circuit is simpler and more efficient and has more pullability than a third overtone circuit. Depending on the manufacturer, the highest available fundamental frequency may be 25 MHz to 66 MHz. A major reason for the wide use of crystal oscillators is their high Q factor.

A typical Q value for a quartz oscillator ranges from 10 4 to 10 6 , compared to perhaps 10 2 for an LC oscillator. The maximum Q for a high stability quartz oscillator can be estimated as Q = 1.6 × 10 7 /f, where f is the resonant frequency in megahertz. One of the most important traits of quartz crystal oscillators is that they can exhibit very low phase noise.

In many oscillators, any spectral energy at the resonant frequency is amplified by the oscillator, resulting in a collection of tones at different phases. In a crystal oscillator, the crystal mostly vibrates in one axis, therefore only one phase is dominant.

This property of low phase noise makes them particularly useful in telecommunications where stable signals are needed, and in scientific equipment where very precise time references are needed. Environmental changes of temperature, humidity, pressure, and vibration can change the resonant frequency of a quartz crystal, but there are several designs that reduce these environmental effects.

These include the TCXO, MCXO, and OCXO which are defined below. These designs, particularly the OCXO, often produce devices with excellent short-term stability. The limitations in short-term stability are due mainly to noise from electronic components in the oscillator circuits.

Long-term stability is limited by aging of the crystal. Due to aging and environmental factors (such as temperature and vibration), it is difficult to keep even the best quartz oscillators within one part in 10 10 of their nominal frequency without constant adjustment. For this reason, atomic oscillators are used for applications requiring better long-term stability and accuracy.

Spurious frequencies

For crystals operated at series resonance or pulled away from the main mode by the inclusion of a series inductor or capacitor, significant (and temperature-dependent) spurious responses may be experienced. Though most spurious modes are typically some tens of kilohertz above the wanted series resonance, their temperature coefficient is different from the main mode, and the spurious response may move through the main mode at certain temperatures.

Even if the series resistances at the spurious resonances appear higher than the one at the wanted frequency, a rapid change in the main mode series resistance can occur at specific temperatures when the two frequencies are coincidental. A consequence of these activity dips is that the oscillator may lock at a spurious frequency at specific temperatures.

This is generally minimized by ensuring that the maintaining circuit has insufficient gain to activate unwanted modes. Spurious frequencies are also generated by subjecting the crystal to vibration. This modulates the resonant frequency to a small degree by the frequency of the vibrations.

SC-cut (Stress Compensated) crystals are designed to minimize the frequency effect of mounting stress and they are therefore less sensitive to vibration. Acceleration effects including gravity are also reduced with SC-cut crystals, as is frequency change with time due to long term mounting stress variation.

There are disadvantages with SC-cut shear mode crystals, such as the need for the maintaining oscillator to discriminate against other closely related unwanted modes and increased frequency change due to temperature when subject to a full ambient range. SC-cut crystals are most advantageous where temperature control at their temperature of zero temperature coefficient (turnover) is possible, under these circumstances an overall stability performance from premium units can approach the stability of rubidium frequency standards.

Commonly used crystal frequencies

Crystals can be manufactured for oscillation over a wide range of frequencies, from a few kilohertz up to several hundred megahertz. Many applications call for a crystal oscillator frequency conveniently related to some other desired frequency, so hundreds of standard crystal frequencies are made in large quantities and stocked by electronics distributors.

For example 3.579545 MHz crystals, which were made in large quantities for NTSC color television receivers, are now popular for many non-television applications (although most modern television receivers now use other frequency crystals for the color decoder). Using frequency dividers, frequency multipliers and phase-locked loop circuits, it is practical to derive a wide range of frequencies from one reference frequency.

Stability

The frequency stability is determined by the crystal's quality factor (Q factor). It is inversely dependent on the frequency, and on the constant that is dependent on the particular cut.

Other factors influencing Q are the overtone used, the temperature, the level of driving of the crystal, the quality of the surface finish, the mechanical stresses imposed on the crystal by bonding and mounting, the geometry of the crystal and the attached electrodes, the material purity and defects in the crystal, type and pressure of the gas in the enclosure, interfering modes, and presence and absorbed dose of ionizing and neutron radiation. The stability of AT cut crystals decreases with increasing frequency.

For more accurate higher frequencies it is better to use a crystal with lower fundamental frequency, operating at an overtone. A badly designed oscillator circuit may suddenly begin oscillating on an overtone. In 1972, a train in Fremont, California crashed due to a faulty oscillator.

An inappropriate value of the tank capacitor caused the crystal in a control board to be overdriven, jumping to an overtone, and causing the train to speed up instead of slowing down.

Drive level

The crystals have to be driven at the appropriate drive level. Low-frequency crystals, especially flexural-mode ones, may fracture at too high drive levels. The drive level is specified as the amount of power dissipated in the crystal.

The appropriate drive levels are about 5 μW for flexural modes up to 100 kHz, 1 μW for fundamental modes at 1–4 MHz, 0.5 μW for fundamental modes 4–20 MHz and 0.5 μW for overtone modes at 20–200 MHz. Too low drive level may cause problems with starting the oscillator. Low drive levels are better for higher stability and lower power consumption of the oscillator.

Higher drive levels, in turn, reduce the impact of noise by increasing the signal-to-noise ratio.

Crystal cuts

The resonator plate can be cut from the source crystal in many different ways. The orientation of the cut influences the crystal's aging characteristics, frequency stability, thermal characteristics, and other parameters. These cuts operate at bulk acoustic wave (BAW); for higher frequencies, surface acoustic wave (SAW) devices are employed.

Image of several crystal cuts The letter ‘T’ in the cut name marks a temperature-compensated cut – a cut oriented in a way that the temperature coefficients of the lattice are minimal; the FC and SC cuts are also temperature-compensated. The high frequency cuts are mounted by their edges, usually on springs; the stiffness of the spring has to be optimal, as if it is too stiff, mechanical shocks could be transferred to the crystal and cause it to break, and too little stiffness may allow the crystal to collide with the inside of the package when subjected to a mechanical shock, and break.

Strip resonators, usually AT cuts, are smaller and therefore less sensitive to mechanical shocks. At the same frequency and overtone, the strip has less pullability, higher resistance, and higher temperature coefficient.

The low frequency cuts are mounted at the nodes where they are virtually motionless; thin wires are attached at such points on each side between the crystal and the leads. The large mass of the crystal suspended on the thin wires makes the assembly sensitive to mechanical shocks and vibrations.

The crystals are usually mounted in hermetically sealed glass or metal cases, filled with a dry and inert atmosphere, usually vacuum, nitrogen, or helium. Plastic housings can be used as well, but those are not hermetic and another secondary sealing has to be built around the crystal.

Several resonator configurations are possible, in addition to the classical way of directly attaching leads to the crystal. E.g. the BVA resonator (Boîtier à Vieillissement Amélioré, Enclosure with Improved Aging), developed in 1976; the parts that influence the vibrations are machined from a single crystal (which reduces the mounting stress), and the electrodes are deposited not on the resonator itself but on the inner sides of two condenser discs made of adjacent slices of the quartz from the same bar, forming a three-layer sandwich with no stress between the electrodes and the vibrating element.

The gap between the electrodes and the resonator act as two small series capacitors, making the crystal less sensitive to circuit influences. The architecture eliminates the effects of the surface contacts between the electrodes, the constraints in the mounting connections, and the issues related to ion migration from the electrodes into the lattice of the vibrating element.

The resulting configuration is rugged, resistant to shock and vibration, resistant to acceleration and ionizing radiation, and has improved aging characteristics. AT cut is usually used, though SC cut variants exist as well. BVA resonators are often used in spacecraft applications.

In the 1930s to 1950s, it was fairly common for people to adjust the frequency of the crystals by manual grinding. The crystals were ground using a fine abrasive slurry, or even a toothpaste, to increase their frequency. A slight decrease by 1–2 kHz when the crystal was overground was possible by marking the crystal face with a pencil lead, at the cost of a lowered .

The frequency of the crystal is slightly adjustable ("pullable") by modifying the attached capacitances. A varactor, a diode with capacitance depending on applied voltage, is often used in voltage-controlled crystal oscillators, VCXO.

The crystal cuts are usually AT or rarely SC, and operate in fundamental mode; the amount of available frequency deviation is inversely proportional to the square of the overtone number, so a third overtone has only one-ninth of the pullability of the fundamental mode. SC cuts, while more stable, are significantly less pullable.

Circuit notations and abbreviations

On electrical schematic diagrams, crystals are designated with the class letter Y (Y1, Y2, etc.). Oscillators, whether they are crystal oscillators or others, are designated with the class letter G (G1,

G2, etc.). Crystals may also be designated on a schematic with X or XTAL (a phonetic abbreviation, comparable to using Xmas for Christmas), or a crystal oscillator with XO. Crystal oscillator types and their abbreviations: ATCXO — analog temperature-compensated crystal oscillator CDXO — calibrated dual crystal oscillator DTCXO — digital temperature-compensated crystal oscillator EMXO — evacuated miniature crystal oscillator GPSDO — GPS-disciplined oscillator MCXO — microcomputer-compensated crystal oscillator OCVCXO — oven-controlled voltage-controlled crystal oscillator OCXO — oven-controlled crystal oscillator RbXO — rubidium crystal oscillators (RbXO), a crystal oscillator (can be an MCXO) synchronized with a built-in rubidium standard which is run only occasionally to save power TCVCXO — temperature-compensated voltage-controlled crystal oscillator TCXO — temperature-compensated crystal oscillator TMXO – tactical miniature crystal oscillator TSXO — temperature-sensing crystal oscillator, an adaptation of the TCXO VCTCXO — voltage-controlled temperature-compensated crystal oscillator VCXO — voltage-controlled crystal oscillator

See also

Clock generator Clock drift – Clock drift measurements of crystal oscillators can be used to build random number generators. Crystal filter Erhard Kietz, who worked on electronic tuning forks and with quartz crystals for precise signal frequencies Issac Koga – inventor of the temperature-stable R1 Koga cut Pierce oscillator Thin-film thickness monitor Variable-frequency oscillator (VFO)

Further reading

(Alternative downloads: QSL: - 0 1 2 3 4 5 6 7 8 9 10. AXTAL ZIP : - 0 1 2 3 4 5 6 7 8 9 10.)

Introduction to quartz frequency standards Distortions in Crystal Oscillators Quartz crystal resonators and oscillators Multipage summary of quartz crystals & their oscillators, filters, etc

Text derived from https://en.wikipedia.org/w/index.php?oldid=1377442599 under CC BY-SA 4.0; modifications have been made.

Words in each sectionCrystal oscillator circ…Crystal oscillator circuitsCrystal oscillator circuits: 700 words700Crystal cutsCrystal cutsCrystal cuts: 630 words630HistoryHistoryHistory: 468 words468Resonance modesResonance modesResonance modes: 371 words371PrinciplePrinciplePrinciple: 340 words340Spurious frequenciesSpurious frequenciesSpurious frequencies: 286 words286Electrical modelElectrical modelElectrical model: 244 words244StabilityStabilityStability: 191 words191Circuit notations and a…Circuit notations and abbreviationsCircuit notations and abbreviations: 160 words160Drive levelDrive levelDrive level: 122 words122Commonly used crystal f…Commonly used crystal frequenciesCommonly used crystal frequencies: 113 words113TerminologyTerminologyTerminology: 96 words96See alsoSee alsoSee also: 53 words53Further readingFurther readingFurther reading: 29 words29
Words in each section. Measured from the stored article body; sections below the minimum are not plotted.

Provenance

snapshot enwiki-001377442599 · captured 2026-09-29 · ledger · version history

Cite this page as: encyclopegia.org, “Crystal oscillator”, snapshot enwiki-001377442599. https://encyclopegia.org/a/crystal-oscillator

Sources cited in this revision

30 named source(s) extracted from the cited revision. A source with no author is shown by its publication; nothing is invented.