Cutting force (machining)

Cutting force in machining is the physical resistance offered by a workpiece material to being penetrated and deformed by a cutting tool to form a chip.

Uses your system voice; voice and rate in settings.

Snapshot

≈ 7 min read

Names in other languages

No names in other languages are held for this entry yet.

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

Cutting force in machining is the physical resistance offered by a workpiece material to being penetrated and deformed by a cutting tool to form a chip. In machining, estimating the required cutting forces is essential to ensure proper process planning.

An adequate estimation allows for the correct selection of cutting tools and necessary fixtures to avoid dimensional and geometric accuracy issues due to deflections, vibrations, etc. At the same time, estimating cutting forces enables the calculation of the required cutting power, allowing for the correct selection of the machine tool (lathe, milling machine, etc.) . Taking the turning process as an example of a machining operation, Figure 1 shows the forces that appear during the cutting process. The principal cutting force ( F_t ) defines the resultant force in the direction of the cutting motion.

The normal component or thrust force ( N_t ) is the force perpendicular to the cutting edge and the principal cutting force. Generally, this force accounts for 50% to 70% of the cutting force . Depending on the tool's lead angle (principal position angle), this force results in an axial component ( N_{ta} ) and a radial component ( N_{tr} ).

Depending on the specific machining operation, these components result in the feed forces.…

Cutting force in machining is the physical resistance offered by a workpiece material to being penetrated and deformed by a cutting tool to form a chip. In machining, estimating the required cutting forces is essential to ensure proper process planning.

An adequate estimation allows for the correct selection of cutting tools and necessary fixtures to avoid dimensional and geometric accuracy issues due to deflections, vibrations, etc. At the same time, estimating cutting forces enables the calculation of the required cutting power, allowing for the correct selection of the machine tool (lathe, milling machine, etc.) . Taking the turning process as an example of a machining operation, Figure 1 shows the forces that appear during the cutting process. The principal cutting force ( F_t ) defines the resultant force in the direction of the cutting motion.

The normal component or thrust force ( N_t ) is the force perpendicular to the cutting edge and the principal cutting force. Generally, this force accounts for 50% to 70% of the cutting force . Depending on the tool's lead angle (principal position angle), this force results in an axial component ( N_{ta} ) and a radial component ( N_{tr} ).

Depending on the specific machining operation, these components result in the feed forces. For example, in a straight turning operation where the tool moves in a longitudinal direction (parallel to the workpiece axis), the axial normal component is equivalent to the feed force required for the operation.

Cutting force calculation

Although various methods exist for estimating cutting forces in machining (see technical textbooks , ), the most commonly used approach is the specific cutting pressure method. Most cutting tool manufacturers (e.g., Sandvik Coromant, Mitsubishi Materials) provide data related to specific pressure to facilitate the estimation of forces and power in machining operations.

This calculation method establishes that the cutting force is directly proportional to the undeformed chip cross-section, using a proportionality constant known as specific cutting pressure or specific cutting resistance. This proportionality constant is expressed as : F_t = k_c \cdot A_c where F_t is the cutting force and A_c is the undeformed chip cross-section.

The cutting pressure depends on several factors, such as : Workpiece material: A material with higher mechanical strength has a higher k_c . Cutting tool material: Together with the workpiece material, these define the friction coefficient between the chip and the tool's rake face. Cutting tools with a lower friction coefficient during cutting result in a lower k_c . Cutting tool geometry: The rake angle of the cutting tool influences the deformation work experienced by the chip.

Larger rake angles result in lower k_c values. Chip cross-section: Experimental tests show that k_c is a function of the chip cross-section area, with k_c decreasing as the area increases. For the same chip width, increasing the chip thickness causes k_c to decrease.

Cutting speed: k_c tends to slightly decrease as cutting speed increases, although it remains constant at high speeds. Lubrication and cooling conditions: Better lubrication between the chip and the cutting tool reduces the friction coefficient, thereby decreasing k_c . Tool wear: Increased wear modifies the cutting tool geometry and increases friction, leading to an increase in the specific cutting pressure k_c . To calculate cutting forces using specific cutting pressure, tables are used that record the variations of k_c based on variables dependent on the aforementioned factors.

Thus, k_c is typically obtained as : k_c = k_{c1} \cdot f_e \cdot f_{\gamma} The value k_{c1} represents the specific cutting pressure for a specific material under fixed cutting conditions (using a reference tool with a specific rake angle and machining a specific chip thickness). The values f_e and f_{\gamma} are correction factors for chip thickness and rake angle, respectively, used to adjust the k_{c1} value according to actual cutting conditions.

The k_{c1} values are tabulated based on tool material, workpiece material, etc. Specifically, for the f_{\gamma} factor, the correction is estimated as: f_{\gamma} = 1 + 0.01 \cdot (\gamma_0 - \gamma) where \gamma_0 is the rake angle of the reference tool (usually 0°) and \gamma is the rake angle of the tool used in machining. This shows that a tool with a smaller rake angle than the reference tool results in a correction factor greater than 1, indicating higher cutting forces.

For the f_e factor, it is sometimes estimated directly from tables or calculated as: f_e = (t)^{-m_c} where t is the chip thickness of the analyzed operation and m_c is a value found in tables that depends on the machined material and cutting conditions. Regarding the calculation of cutting power, it is estimated as: P_t = F_t \cdot V_c where F_t is the cutting force and V_c is the cutting speed.

The normal force components and the feed rate are generally not considered, as they represent a much lower power consumption compared to the cutting power—typically around only 1% . F_t = k_c \cdot A_c The operation is performed with a depth of cut of 2 mm (reducing from Ø30 to Ø26 mm); therefore, the chip cross-section area (Figure 3) is: A_c = b \cdot t = s \cdot a = 2 \cdot 0.1 = 0.2 mm^2 where b is the chip width, t is the chip thickness, s is the feed per revolution, and a is the depth of cut.

The specific cutting pressure is calculated as: k_c = k_{c1} \cdot f_e \cdot f_{\gamma} For unalloyed steel, according to the table, the values are k_{c1}=1,500 N/mm^2 and m_c=0.25 . Thus, the chip thickness correction factor is: f_e = (t)^{-m_c} = (0.097)^{-0.25} = 1.794 Since the chip thickness is: t = s \cdot \sin(\kappa) = 0.1 \cdot \sin(75^\circ) = 0.097 mm Furthermore, the rake angle correction factor is: f_{\gamma} = 1 + 0.01 \cdot (\gamma_0 - \gamma) = 1 + 0.01 \cdot (0 - 2) = 0.98 Given that \gamma_{0}=0 for the specific pressure table, then: k_c = k_{c1} \cdot f_e \cdot f_{\gamma} = 1,500 \cdot 1.794 \cdot 0.98 = 2,637 N/mm^2 And the cutting force is: F_t = k_c \cdot A_c = 2,637 \cdot 0.2 = 527.4 N

Official website of Sandvik Coromant, featuring technical resources for cutting force calculations

Text derived from https://en.wikipedia.org/w/index.php?oldid=1359169235 under CC BY-SA 4.0; modifications have been made.

Provenance

snapshot enwiki-001359169235 · captured 2026-06-13 · not yet sealed in the ledger · verify the chain · version history

Cite this page as: encyclopegia.org, “Cutting force (machining)”, snapshot enwiki-001359169235. https://encyclopegia.org/a/cutting-force-machining

Sources cited in this revision

No external citation was extracted for this revision. That is a statement about the source, not a claim that none exists.