DDR4 SDRAM

Double Data Rate 4 Synchronous Dynamic Random-Access Memory (DDR4 SDRAM) is a type of synchronous dynamic random-access memory with a high-bandwidth ("double data rate") interface.

Uses your system voice; voice and rate in settings.

Snapshot

≈ 5 min read

Names in other languages

No names in other languages are held for this entry yet.

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

Double Data Rate 4 Synchronous Dynamic Random-Access Memory (DDR4 SDRAM) is a type of synchronous dynamic random-access memory with a high-bandwidth ("double data rate") interface. Released to the market in 20141, it is a variant of dynamic random-access memory (DRAM), some of which have been in use since the early 1970s, and a higher-speed successor to the DDR2 and DDR3 technologies.

DDR4 is not compatible with any earlier type of random-access memory (RAM) due to different signaling voltage and physical interface, besides other factors. DDR4 SDRAM was released to the public market in Q2 2014, focusing on ECC memory, while the non-ECC DDR4 modules became available in Q3 2014, accompanying the launch of Haswell-E processors that require DDR4 memory.

Double Data Rate 4 Synchronous Dynamic Random-Access Memory (DDR4 SDRAM) is a type of synchronous dynamic random-access memory with a high-bandwidth ("double data rate") interface. Released to the market in 2014, it is a variant of dynamic random-access memory (DRAM), some of which have been in use since the early 1970s, and a higher-speed successor to the DDR2 and DDR3 technologies.

DDR4 is not compatible with any earlier type of random-access memory (RAM) due to different signaling voltage and physical interface, besides other factors. DDR4 SDRAM was released to the public market in Q2 2014, focusing on ECC memory, while the non-ECC DDR4 modules became available in Q3 2014, accompanying the launch of Haswell-E processors that require DDR4 memory.

The activate command requires more address bits than any other (18 row address bits in a 16 Gbit part), so the standard , , and active low signals are shared with high-order address bits that are not used when is high. The combination of =L and = =H that previously encoded an activate command is unused.

As in previous SDRAM encodings, A10 is used to select command variants: auto-precharge on read and write commands, and one bank vs. all banks for the precharge command. It also selects two variants of the ZQ calibration command. As in DDR3, A12 is used to request burst chop: truncation of an 8-transfer burst after four transfers.

Although the bank is still busy and unavailable for other commands until eight transfer times have elapsed, a different bank can be accessed. Also, the number of bank addresses has been increased greatly. There are four bank select bits to select up to 16 banks within each DRAM: two bank address bits (BA0, BA1), and two bank group bits (BG0, BG1).

There are additional timing restrictions when accessing banks within the same bank group; it is faster to access a bank in a different bank group. In addition, there are three chip select signals (C0, C1, C2), allowing up to eight stacked chips to be placed inside a single DRAM package.

These effectively act as three more bank select bits, bringing the total to seven (128 possible banks). Standard transfer rates are 1600, 1866, 2133, 2400, 2666, 2933, and 3200 MT/s ( , , , , , , and  GHz clock frequencies, double data rate), with speeds up to DDR4-4800 (2400 MHz clock) commercially available.

Successor

At the 2016 Intel Developer Forum, the future of DDR5 SDRAM was discussed. The specifications were finalized at the end of 2016 but no modules would be available until 2020. Other memory technologies namely HBM in version 3 and 4 aiming to replace DDR4 have also been proposed.

In 2011, JEDEC introduced the Wide I/O 2 standard, which features stacked memory dies placed directly on top of the CPU within the same package. This configuration provides higher bandwidth and improved power efficiency compared to DDR4 SDRAM, thanks to its wide interface and short signal lengths.

Wide I/O 2 aims to replace various mobile DDRX SDRAM standards used in high-performance embedded and mobile devices like smartphones. In parallel, Hynix developed High Bandwidth Memory (HBM), standardized as JEDEC JESD235.

Both Wide I/O 2 and HBM utilize a very wide parallel memory interface—up to 512 bits for Wide I/O 2 compared to 64 bits for DDR4—although they operate at lower frequencies than DDR4. Wide I/O 2 is designed for high-performance, compact devices, often integrated into processors or system on a chip (SoC) packages.

In contrast, HBM targets graphics memory and general computing, while Hybrid Memory Cube (HMC) is aimed at high-end servers and enterprise applications. Micron Technology's Hybrid Memory Cube (HMC) stacked memory uses a serial interface.

Many other computer buses have migrated towards replacing parallel buses with serial buses, for example by the evolution of Serial ATA replacing Parallel ATA, PCI Express replacing PCI, and serial ports replacing parallel ports. In general, serial buses are easier to scale up and have fewer wires/traces, making circuit boards using them easier to design.

In the longer term, experts speculate that non-volatile RAM types like PCM (phase-change memory), RRAM (resistive random-access memory), or MRAM (magnetoresistive random-access memory) could replace DDR4 SDRAM and its successors. GDDR5 SGRAM is a graphics type of DDR3 synchronous graphics RAM, which was introduced before DDR4, and is not a successor to DDR4.

Text derived from https://en.wikipedia.org/w/index.php?oldid=1378399333 under CC BY-SA 4.0; modifications have been made.

References

  1. ↩Wikipedia “DDR4 SDRAM” revision 1378399333 · retrieved 2026-10-20 release date (×2) · confidence 0.95 revision URL