Defensive fighting position
during the 1958 Lebanon crisis A defensive fighting position is a type of earthwork constructed in a military context, generally large enough to accommodate anything from one soldier to a fire team (or similar sized unit).
≈ 6 min read
Defensive fighting position. encyclopegia.org, snapshot enwiki-001369812420. /a/defensive-fighting-position
Names in other languages
No names in other languages are held for this entry yet.
Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.
during the 1958 Lebanon crisis A defensive fighting position is a type of earthwork constructed in a military context, generally large enough to accommodate anything from one soldier to a fire team (or similar sized unit).
History
in a Tobruk DFP along the Atlantic Wall, 1944 The Imperial Russian Army were the first to use what was later termed "rifle pits" during the Crimean War. These were small holes dug just in front of their trenches, large enough to fit anywhere from one to twenty soldiers. These soldiers were armed with rifles so as to harass Allied work parties advancing their own trench lines.
Such pits were among the fortifications Major Richard Delafield observed and reported on as part of the Delafield Commission. Rifle pits were used again during the American Civil War for the same purpose of providing a defensive position for one or more skirmishers or pickets.
However, while military engineers recognized the difference, many soldiers at the time used the term interchangeably for other defensive earthworks. In general, it was the most commonly used word to describe any defensive fighting position meant for infantry. During the fighting in North Africa (1942–43), U.S. forces employed the shell scrape.
This was a very shallow excavation allowing one soldier to lie horizontally while shielding his body from nearby shell bursts and small arms fire. The shell scrape soon proved inadequate in this role, as the few inches of dirt above the soldier's body could often be penetrated by bullets or shell fragments.
It also exposed the user to assault by enemy tanks, which could crush a soldier inside a shallow shell scrape by driving into it, then making a simple half-turn. After the Battle of Kasserine Pass (early 1943), U.S. troops increasingly adopted the modern foxhole, a vertical, bottle-shaped hole that allowed a soldier to stand and fight with head and shoulders exposed.
The foxhole widened near the bottom to allow a soldier to crouch down while under intense artillery fire or tank attack. Foxholes could be enlarged to two-soldier fighting positions, as well as excavated with firing steps for crew-served weapons or sumps for water drainage or live enemy grenade disposal.
Tobruks
The Germans used hardened fortifications in North Africa and later in other fortifications, such as the Atlantic Wall, that were in essence foxholes made from concrete. The Germans knew them officially as Ringstände; the Allies called them "Tobruks" because they had first encountered the structures during the fighting in Africa.
Frequently, the Germans put a turret from an obsolete French or German tank on the foxhole. This gave the Tobruk enhanced firepower and the gunner protection from shrapnel and small arms.
Image:German turret at Omaha Beach.jpg|German VK 3001H prototype turret mounted on "Tobruk" at Omaha Beach, June 1944 File:Tobruk at the CI Military Museum.JPG|Tobruk protecting the entrance to the bunker that now houses the Channel Islands Military Museum. This turret from a Renault R35 was originally employed on a Tobruk at Saint Aubin's Fort, Jersey.
Modern designs
Modern militaries publish and distribute elaborate field manuals for the proper construction of DFPs in stages. Initially, a shallow "shell scrape" is dug, often called a ranger grave, which provides very limited protection. Each stage develops the fighting position, gradually increasing its effectiveness, while always maintaining functionality.
In this way, a soldier can improve the position over time, while being able to stop at any time and use the position in a fight. Typically, a DFP is a pit or trench dug deep enough to stand in, with only the head exposed, and a small step at the bottom, called a fire step, that allows the soldier to crouch on to avoid fire and tank treads.
The fire step usually slopes down into a deeper narrow slit called a grenade sump at the bottom to allow for live grenades to be kicked in to minimize damage from grenade fragments. When possible, DFPs are revetted with corrugated iron, star pickets and wire or local substitutes.
Ideally, the revetting will also be dug in below ground level so as to minimise damage from fire and tank tracks. The revetting helps the DFP resist cave-in from near misses from artillery or mortars and tank tracks. Time permitting, DFPs can be enlarged to allow a machine gun crew and ammunition to be protected, as well as additional overhead cover via timbers.
In training, DFPs are usually dug by hand or in some cases by mechanical trench diggers. On operations, explosives, especially shaped charges ("beehives"), may be used to increase the speed of development. Developing and maintaining DFPs is a constant and ongoing task for soldiers deployed in combat areas.
For this reason, in some armies, infantry soldiers are referred to as "gravel technicians", as they spend so much time digging. Because of the large expenditure in effort and materials required to build a DFP, it is important to ensure that the DFP is correctly sited.
In order to site the DFP, the officer in charge ("OIC") should view the ground from the same level that the intended user's weapons will be sighted from. Normally, the OIC will need to lie on his belly to obtain the required perspective. This ensures that the position will be able to cover the desired sector.
File:3rd Battalion 4th Marines dig in near Iraqi border 2003-03-20.JPEG|US Marines digging "fighting holes" near the Iraqi border, 2003. File:US_Navy_030209-N-5319A-005_Seabees_of_Naval_Mobile_Construction_Battalion_Seventy-Four_(NMCB-74)_have_only_ten_minutes_to_dig.jpg|US Navy Seabees digging "hasty scrapes", 2003.
File:US Navy 030209-N-5319A-006 Construction Electrician 3rd Class Justin Vizcarrondo assigned to Naval Mobile Construction Battalion Seventy-Four (NMCB-74) uses an entrenching tool to dig a hasty scrape.jpg|US Navy Seabees near completed fighting position, 2003. File:US Navy 101104-N-8816D-008 Chief Steelworker Corey Mead, assigned to Naval Mobile Construction Battalion (NMCB) 133, digs a fighting position during training.jpg|US Navy Seabees constructing a defensive machine gun position during training, 2010.
File:US Navy 081104-N-7367K-011 Seabees assigned to Naval Mobile Construction Battalion (NMCB) 1 keep guard the protective lines from a fighting position at forward operating base zero.jpg|US Navy Seabees with a completed defensive machine gun position during training, 2008. File:US Navy 101017-N-4440L-022 Equipment Operator Constructionman Travis Love, assigned to the air detail of Naval Mobile Construction Battalion (NMCB).jpg|US Navy Seabees completed defensive machine gun position during training with camouflage netting and timber supports, 2010.
See also
Pillbox (military) Sangar Spider hole Shell scrape Tett turret Trench warfare All-around defense/Perimeter defense Entrenching tool
External links
U.S. WWII Newsmap, "Foxholes are Life Savers", hosted by the UNT Libraries Digital Collections
Text derived from https://en.wikipedia.org/w/index.php?oldid=1369812420 under CC BY-SA 4.0; modifications have been made.