Direct energy conversion
Direct energy conversion (DEC) or simply direct conversion converts a charged particle's kinetic energy into a voltage.
≈ 5 min read
Names in other languages
No names in other languages are held for this entry yet.
Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.
Direct energy conversion (DEC) or simply direct conversion converts a charged particle's kinetic energy into a voltage. It is a scheme for power extraction from nuclear fusion.
The Venetian blind
The Venetian blind design is a type of electrostatic direct collector. The Venetian Blind design name comes from the visual similarity of the ribbons to venetian window blinds. Designs in the early 1970s by William Barr and Ralph Moir used repeating metal ribbons at a specified angle as the ion collector plates.
These metal ribbon-like surfaces are more transparent to ions going forward than to ions going backward. Ions pass through surfaces of successively increasing potential until they turn and start back, along a parabolic trajectory. They then see opaque surfaces and are caught.
Thus ions are sorted by energy with high-energy ions being caught on high-potential electrodes. William Barr and Ralph Moir then ran a group which did a series of direct energy conversion experiments through the late 1970s and early 1980s. The first experiments used beams of positives and negatives as fuel, and demonstrated energy capture at a peak efficiency of 65 percent and a minimum efficiency of 50 percent.
The following experiments involved a true plasma direct converter that was tested on the Tandem Mirror Experiment (TMX), an operating magnetic mirror fusion reactor. In the experiment, the plasma moved along diverging field lines, spreading it out and converting it into a forward moving beam with a Debye length of a few centimeters.
Suppressor grids then reflect the electrons, and collector anodes recovered the ion energy by slowing them down and collecting them at high-potential plates. This machine demonstrated an energy capture efficiency of 48 percent.
However, Marshall Rosenbluth argued that keeping the plasma's neutral charge over the very short Debye length distance would be very challenging in practice, though he said that this problem would not occur in every version of this technology. The Venetian Blind converter can operate with 100 to 150 keV D-T plasma, with an efficiency of about 60% under conditions compatible with economics, and an upper technical conversion efficiency up to 70% ignoring economic limitations.
Periodic electrostatic focusing
A second type of electrostatic converter initially proposed by Post, then developed by Barr and Moir, is the Periodic Electrostatic Focusing concept. Like the Venetian Blind concept, it is also a direct collector, but the collector plates are disposed in many stages along the longitudinal axis of an electrostatic focusing channel.
As each ion is decelerated along the channel toward zero energy, the particle becomes "over-focused" and is deflected sideways from the beam, then collected. The Periodic Electrostatic Focusing converter typically operates with a 600 keV D-T plasma (as low as 400 keV and up to 800 keV) with efficiency of about 60% under conditions compatible with economics, and an upper technical conversion efficiency up to 90% ignoring economic limitations.
Inverse cyclotron converter (ICC)
Original direct converters were designed to extract the energy carried by 100 to 800 keV ions produced by D-T fusion reactions. Those electrostatic converters are not suitable for higher energy product ions above 1 MeV generated by other fusion fuels like the D- 3 He or the p- 11 B aneutronic fusion reactions.
A much shorter device than the Traveling-Wave Direct Energy Converter has been proposed in 1997 and patented by Tri Alpha Energy, Inc. as an Inverse Cyclotron Converter (ICC). The ICC is able to decelerate the incoming ions based on experiments made in 1950 by Felix Bloch and Carson D. Jeffries, in order to extract their kinetic energy.
The converter operates at 5 MHz and requires a magnetic field of only 0.6 tesla. The linear motion of fusion product ions is converted to circular motion by a magnetic cusp. Energy is collected from the charged particles as they spiral past quadrupole electrodes.
More classical electrostatic collectors would also be used for particles with energy less than 1 MeV. The Inverse Cyclotron Converter has a maximum projected efficiency of 90%.
X-ray photoelectric converter
A significant amount of the energy released by fusion reactions is composed of electromagnetic radiation, essentially X-rays due to Bremsstrahlung. Those X-rays can not be converted into electric power with the various electrostatic and magnetic direct energy converters listed above, and their energy is lost.
Whereas more classical thermal conversion has been considered with the use of a radiation/boiler/energy exchanger where the X-ray energy is absorbed by a working fluid at temperatures of several thousand degrees, more recent research done by companies developing nuclear aneutronic fusion reactors, like Lawrenceville Plasma Physics (LPP) with the Dense Plasma Focus, and Tri Alpha Energy, Inc. with the Colliding Beam Fusion Reactor (CBFR), plan to harness the photoelectric and Auger effects to recover energy carried by X-rays and other high-energy photons. Those photoelectric converters are composed of X-ray absorber and electron collector sheets nested concentrically in an onion-like array.
Indeed, since X-rays can go through far greater thickness of material than electrons can, many layers are needed to absorb most of the X-rays. LPP announces an overall efficiency of 81% for the photoelectric conversion scheme.
Text derived from https://en.wikipedia.org/w/index.php?oldid=1334548750 under CC BY-SA 4.0; modifications have been made.