{
  "id": "enwiki-001373990564",
  "slug": "drilling",
  "title": "Drilling",
  "qid": "",
  "lead": "Drilling is a cutting process where a drill bit is spun to cut a hole of circular cross-section in solid materials. The drill bit is usually a rotary cutting tool, often multi-point. The bit is pressed against the work-piece and rotated at rates from hundreds to thousands of revolutions per minute. This forces the cutting edge against the work-piece, cutting off chips (swarf) from the hole as it is drilled. In rock drilling, the hole is usually not made through a circular cutting motion, though the bit is usually rotated. Instead, the hole is usually made by hammering a drill bit into the hole with quickly repeated short movements. The hammering action can be performed from outside the hole (top-hammer drill) or within the hole (down-the-hole drill, DTH). Drills used for horizontal drilling are called drifter drills. In rare cases, specially-shaped bits are used to cut holes of non-circular cross-section; a square cross-section is possible.",
  "body": "Drilling is a cutting process where a drill bit is spun to cut a hole of circular cross-section in solid materials. The drill bit is usually a rotary cutting tool, often multi-point. The bit is pressed against the work-piece and rotated at rates from hundreds to thousands of revolutions per minute. This forces the cutting edge against the work-piece, cutting off chips (swarf) from the hole as it is drilled. In rock drilling, the hole is usually not made through a circular cutting motion, though the bit is usually rotated. Instead, the hole is usually made by hammering a drill bit into the hole with quickly repeated short movements. The hammering action can be performed from outside the hole (top-hammer drill) or within the hole (down-the-hole drill, DTH). Drills used for horizontal drilling are called drifter drills. In rare cases, specially-shaped bits are used to cut holes of non-circular cross-section; a square cross-section is possible. ====Trepanning==== while the workpiece is mounted on the cross slide.]] Trepanning is commonly used for creating larger diameter holes (up to ) where a standard drill bit is not feasible or economical. Trepanning removes the desired diameter by cutting out a solid disk similar to the workings of a drafting compass. Trepanning is performed on flat products such as sheet metal, granite (curling stone), plates, or structural members like I-beams. Trepanning can also be useful to make grooves for inserting seals, such as O-rings.",
  "categories": [
    "22920467",
    "22964565",
    "23118434",
    "23137981",
    "23211856",
    "23308705",
    "23308707",
    "23603337",
    "24043274",
    "24745113",
    "26864386"
  ],
  "license": "CC BY-SA 4.0",
  "source_uri": "https://en.wikipedia.org/w/index.php?oldid=1373990564",
  "content_hash": "",
  "created_at": null,
  "updated_at": 1788919590.0,
  "claims": [],
  "contradictions": [],
  "confidence": 0.6,
  "csl": {
    "id": "enwiki-001373990564",
    "type": "webpage",
    "title": "Drilling",
    "author": [
      {
        "family": "Anticloud FZ LLE",
        "literal": "Anticloud FZ LLE"
      }
    ],
    "container-title": "encyclopegia.org",
    "publisher": "Anticloud FZ LLE",
    "publisher-place": "Dubai, United Arab Emirates",
    "URL": "https://encyclopegia.org/a/drilling",
    "issued": {
      "date-parts": [
        [
          2026,
          11,
          21
        ]
      ]
    },
    "accessed": {
      "date-parts": [
        [
          2026,
          11,
          21
        ]
      ]
    },
    "license": "CC BY-SA 4.0",
    "DOI": "eo1:enwiki-001373990564",
    "isBasedOn": "https://en.wikipedia.org/w/index.php?oldid=1373990564",
    "note": "Immutable snapshot enwiki-001373990564"
  }
}