Elasto-capillarity

Elasto-capillarity is the ability of capillary force to deform an elastic material.

Uses your system voice; voice and rate in settings.

Snapshot

≈ 5 min read

Names in other languages

No names in other languages are held for this entry yet.

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

Elasto-capillarity is the ability of capillary force to deform an elastic material. From the viewpoint of mechanics, elastocapillarity phenomena essentially involve competition between the elastic strain energy in the bulk and the energy on the surfaces/interfaces.

In the modeling of these phenomena, some challenging issues are, among others, the exact characterization of energies at the micro scale, the solution of strongly nonlinear problems of structures with large deformation and moving boundary conditions, and instability of either solid structures or droplets/films.The capillary forces are generally negligible in the analysis of macroscopic structures but often play a significant role in many phenomena at small scales. F_{vertical}=\gamma \times \sin(\theta) = E \times \delta Where F_{vertical} is the force per unit length in the vertical direction \gamma is the surface tension of a liquid E is the Young's modulus of a substrate \delta is deformation of the substrate This gives length scale \delta \sim \gamma\sin(\theta) / E for the deformation of bulk materials caused by the surface tension force.

For example, if a water ( \gamma ~ 72 mN/m) droplet is deposited on the glass ( E ~ 700 GPa), this gives \delta ~10 −12 m which is typically negligible. However, if a water droplet is deposited on the PDMS ( E ~ 300 kPa), this causes the deformation to be \delta ~10 −6 m, which is in micron scale.

This can have great impact on micro/nanotechnology applications where length scale is comparable and "soft" photoresists are used. L_{EC} = (\frac{B}{\gamma})^\frac{1}{2} where B is the bending modulus of an elastic material. γ is the surface tension of a liquid. This provides a comparison between bending stiffness (elasticity) and surface tension (capillarity).

An elastic structure will be significantly deformed once its length is larger than the elasto-capillary length, which can be explained when gain of surface energy of a material is larger than stored elastic energy while bending. In the case of capillary rise between two parallel plates, height of capillary rise can be predicted as Jurin's height if plates are rigid.

Longer the plates, more flexible they become, consequently plates coalesce as a result of deformation induced by capillary force. As observed, length of capillary rise L wet between elastic plates increases linearly with total length of plates L, sets length of dry L d =L-L wet nearly a constant.

By balancing gain of surface energy by capillary force and loss of elastic energy by banding a flexible sheet and minimizing with respect to L d , dry length was found to be: L_d^4 = \frac{9}{2}w^2 L_{EC}^2 Where L_{EC} = (\frac{B}{\gamma})^\frac{1}{2} is the elastocapillary length of sheets w is the distance between two parallel sheets This L d sets the minimum length for parallel sheets to collapse, sheets spontaneously coalesce if they are longer than L d . Above result can be generalized to multiple parallel plates when N elastic plates were used. By assuming these N sheets is N times more rigid than single sheet, such system can be treated as two bundles of N/2 sheets with a distance Nw/2.

Thus the dry length can be written as: L_d^4 = \frac{9}{16} N^{3}w^{2}L_{EC}^2 \Delta p = -\gamma \nabla \cdot \hat n =\gamma (\cfrac{1}{R_1} + \cfrac{1}{R_2}) where: \Delta p is the difference between the pressure across the liquid interface (Pa), \gamma is the surface tension of the liquid (N/m), \hat n is the unit normal pointing out of surface, R_1,R_2 are the principle radii of curvature at any point on the free surface of the liquid film or droplet (m). If the liquid wets the contacting surfaces then this pressure difference is negative i.e. the pressure inside liquid is less than the ambient pressure, and if the liquid doesn't wet the contacting surfaces then the pressure difference is positive and liquid pressure is higher than the ambient pressure. \Delta p = -\gamma (\cos \theta_A+ \cos \theta_B)/h_{fs} where: \theta_A,\theta_B are the liquid-solid contact angles for the lower and upper surfaces, respectively, h_{fs} is the gap between the two solids at the location of the free surface of the liquid. These tensile stresses put the two surfaces into more contact while the compressive stresses due to the elastic deformation of the surfaces tend to resist them.

Two scenarios could happen in this case: 1. The tensile and compressive stresses come into balance which in this case the gap between the two surfaces is in the order of Surface roughness|roughness of the surfaces, or, 2.

The tensile stresses overcome the compressive stresses and the two surfaces come into near complete contact in which gap between surfaces is a small fraction of the surface roughness. The latter case is the reason for failure of most microscale devices.

An estimate of the tensile stresses exerted by the capillary film can be obtained by dividing the adhesion force, P_{liq} , between two surfaces to the area wetted by the liquid film, A_{wet} . Because for relative smooth surfaces, the magnitude of the capillary pressure is predicted to be large, it is anticipated that the capillary pressures will be of large magnitude.

A lot of works have been done to ascertain whether there may be some practical limit to the development of such negative pressures (e.g. ).

Text derived from https://en.wikipedia.org/w/index.php?oldid=1354799772 under CC BY-SA 4.0; modifications have been made.

Sources cited in this revision

No external citation was extracted for this revision. That is a statement about the source, not a claim that none exists.