Electrode

Uses your system voice; voice and rate in settings.

Snapshot

≈ 5 min read

Names in other languages

No names in other languages are held for this entry yet.

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

An electrode is an electrical conductor used to make contact with a nonmetallic part of a circuit (e.g. a semiconductor, an electrolyte, a vacuum or a gas). In electrochemical cells, electrodes are essential parts that can consist of a variety of materials (chemicals) depending on the type of cell. An electrode may be called either a cathode or anode according to the direction of the electric current, unrelated to the potential difference between electrodes. Michael Faraday coined the term " " in 1833; the word recalls the Greek ἤλεκτρον ( , "amber") and ὁδός ( , "path, way"). The electrophore, invented by Johan Wilcke in 1762, was an early version of an electrode used to study static electricity.

An electrode is an electrical conductor used to make contact with a nonmetallic part of a circuit (e.g. a semiconductor, an electrolyte, a vacuum or a gas). In electrochemical cells, electrodes are essential parts that can consist of a variety of materials (chemicals) depending on the type of cell. An electrode may be called either a cathode or anode according to the direction of the electric current, unrelated to the potential difference between electrodes.

Evidence and sources

Michael Faraday coined the term " " in 1833; the word recalls the Greek ἤλεκτρον ( , "amber") and ὁδός ( , "path, way"). The electrophore, invented by Johan Wilcke in 1762, was an early version of an electrode used to study static electricity.

Zn (s) + 2OH − (aq) → ZnO (s) + H 2 O (l) + 2e − \qquad \qquad [E 0 oxidation = −1.28 V] 2MnO 2(s) + H 2 O (l) + 2e − → Mn 2 O 3(s) + 2OH − (aq) \qquad [E 0 reduction = +0.15 V] Overall reaction: Zn (s) + 2MnO 2(s) ZnO (s) + Mn 2 O 3(s) \qquad \qquad [E 0 total = +1.43 V] The ZnO is prone to clumping and will give less efficient discharge if recharged again. It is possible to recharge these batteries but is due to safety concerns advised against by the manufacturer.

Other primary cells include zinc–carbon, zinc–chloride, and lithium iron disulfide. \Delta G^{\dagger} = \frac{1}{4 \lambda} (\Delta G^{0} + \lambda)^{2} In which the \lambda is the reorganisation energy.

Filling this result in the classically derived Arrhenius equation k = A\, \exp\left(\frac{- \Delta G^{\dagger}}{kT}\right), leads to k = A\, \exp\left[{\frac {-(\Delta G^{0} + \lambda)^{2}}{4 \lambda k T}}\right] , with A being the pre-exponential factor, which is usually experimentally determined, although a semi-classical derivation provides more information as is explained below. This classically derived result qualitatively reproduced observations of a maximum electron transfer rate under the conditions .

For a more extensive mathematical treatment one could read the paper by Newton. An interpretation of this result and what a closer look at the physical meaning of the \lambda one can read the paper by Marcus. The situation at hand can be more accurately described by using the displaced harmonic oscillator model, in this model quantum tunneling is allowed. This is needed in order to explain why even at near-zero absolute temperature there are still electron transfers, in contradiction with the classical theory.

Without going into too much detail on how the derivation is done, it rests on using Fermi's golden rule from time-dependent perturbation theory with the full Hamiltonian of the system. It is possible to look at the overlap in the wavefunctions of both the reactants and the products (the right and the left side of the chemical reaction) and therefore when their energies are the same and allow for electron transfer. As touched on before this must happen because only then conservation of energy is abided by.

Skipping over a few mathematical steps the probability of electron transfer can be calculated (albeit quite difficult) using the following formula w_{ET}= \frac \mu = \mu^\text{o} + k\cdot T\cdot\log (\gamma\cdot x) + \Omega \cdot \sigma In this equation, μ represents the chemical potential, with μ o being its reference value. T stands for the temperature and k the Boltzmann constant. The term γ inside the logarithm is the activity and x is the ratio of the ion to the total composition of the electrode.

Impact

The novel term Ω is the partial molar volume of the ion in the host and σ corresponds to the mean stress felt by the system. The result of this equation is that diffusion, which is dependent on chemical potential, gets impacted by the added stress and, therefore changes the battery's performance. Furthermore, mechanical stresses may also impact the electrode's solid-electrolyte-interphase layer. The interface which regulates the ion and charge transfer and can be degraded by stress.

Thus, more ions in the solution will be consumed to reform it, diminishing the overall efficiency of the system. ENiCrMo-3 ENiCrFe-2 ENiCrMo-6 ENiCu-7

Text derived from https://en.wikipedia.org/w/index.php?oldid=1377835571 under CC BY-SA 4.0; modifications have been made.

Sources cited in this revision

21 named source(s) extracted from the cited revision. A source with no author is shown by its publication; nothing is invented.