Electronic specific heat

In solid state physics the electronic specific heat, sometimes called the electron heat capacity, is the specific heat of an electron gas.

Uses your system voice; voice and rate in settings.

Snapshot

≈ 9 min read

Names in other languages

No names in other languages are held for this entry yet.

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

In solid state physics the electronic specific heat, sometimes called the electron heat capacity, is the specific heat of an electron gas. Heat is transported by phonons and by free electrons in solids. For pure metals, however, the electronic contributions dominate in the thermal conductivity.

In impure metals, the electron mean free path is reduced by collisions with impurities, and the phonon contribution may be comparable with the electronic contribution. The one-electron energy levels are specified by the wave vector k through the relation \epsilon(k)=\hbar^2k^2/2m with m the electron mass.

This relation separates the occupied energy states from the unoccupied ones and corresponds to the spherical surface in k-space. As T\rightarrow 0 the ground state distribution becomes: f = \begin{cases} 1 & \mbox{if } \epsilon_f \mu. \\ \end{cases} where f is the Fermi–Dirac distribution \epsilon_f is the energy of the energy level corresponding to the ground state \mu is the ground state energy in the limit T\rightarrow 0 , which thus still deviates from the true ground state energy.

This implies that the ground state is the only occupied state for electrons in the limit T\rightarrow 0 , the f=1 takes the Pauli exclusion principle into account. The internal energy U of a system within the free electron model is given by the sum over one-electron levels times the mean number of electrons in that level: U=2\sum_k \epsilon(\mathbf{k})f(\epsilon(\mathbf{k})) where the factor of 2 accounts for the spin up and spin down states of the electron.

F(\mathbf{k})=\frac{V}{8\pi^3}\sum_k F(\mathbf{k})\Delta \mathbf{k} where V is the volume of the system. For the reduced internal energy u=U/V the expression for U can be rewritten as: u=\int \frac{d\mathbf{k}}{4\pi^3}\epsilon(\mathbf{k})f(\epsilon(\mathbf{k})) and the expression for the electron density n=\frac{N}{V} can be written as: n=\int\frac{d\mathbf{k}}{4\pi^3}f(\epsilon(\mathbf{k})) The integrals above can be evaluated using the fact that the dependence of the integrals on \mathbf{k} can be changed to dependence on \epsilon through the relation for the electronic energy when described as free particles, \epsilon(k)=\hbar^2k^2/2m , which yields for an arbitrary function G : \int\frac{d\mathbf{k}}{4\pi^3}G(\epsilon(\mathbf{k})) = \int_0^\infty \frac{k^2dk}{\pi^2}G(\epsilon(\mathbf{k}))= \int_{-\infty}^\infty d\epsilon D(\epsilon)G(\epsilon) with D(\epsilon) = \begin{cases} \frac{m}{\hbar^2\pi^2}\sqrt{\frac{2m\epsilon}{\hbar^2}} & \mbox{if } \epsilon>0, \\ 0 & \mbox{if } \epsilon which is known as the density of levels or density of states per unit volume such that D(\epsilon) d \epsilon is the total number of states between \epsilon and \epsilon+ d\epsilon .

Using the expressions above the integrals can be rewritten as: \begin{align} u&=\int_{-\infty}^\infty d\epsilon D(\epsilon)\epsilon f(\epsilon) \\ n&=\int_{-\infty}^\infty d\epsilon D(\epsilon)f(\epsilon) \end{align} These integrals can be evaluated for temperatures that are small compared to the Fermi temperature by applying the Sommerfeld expansion and using the approximation that \mu differs from \epsilon_f for T=0 by terms of order T^2 . The expressions become: \begin{align} u&=\int_0^{\epsilon_f} \epsilon D(\epsilon)d\epsilon + \epsilon_f \left( (\mu-\epsilon_f )D(\epsilon_f)+ \frac{\pi^2}{6}(k_{\rm B}T)^2 \dot D(\epsilon_f)\right) + \frac{\pi^2}{6}(k_{\rm B}T)^2 D(\epsilon_f)+ \mathcal{O}(T^4) \\ n&=\int_0^{\epsilon_f} D(\epsilon)d\epsilon + \left( (\mu-\epsilon_f )D(\epsilon_f)+ \frac{\pi^2}{6}(k_{\rm B}T)^2 \dot D(\epsilon_f)\right) \end{align} For the ground state configuration the first terms (the integrals) of the expressions above yield the internal energy and electron density of the ground state.

The expression for the electron density reduces to ( \mu-\epsilon_f )D(\epsilon_f)+ \frac{\pi^2}{6}(k_{\rm B}T)^2 \dot D(\epsilon_f)=0 . Substituting this into the expression for the internal energy, one finds the following expression: u=u_0+\frac{\pi^2}{6}(k_{\rm B}T)^2D(\epsilon_f) C_v=\left( \frac{\partial u}{\partial T} \right)_n = \frac{\pi^2}{3} k_{\rm B}^2TD(\epsilon_f) , for free electrons : C_V = C_v / n = \frac{\pi^2}{2} \frac{k_{\rm B}^2T}{\epsilon_f} Compared to the classical result ( C_V=\tfrac{3}{2}k_{\rm B} ), it can be concluded that this result is depressed by a factor of \frac{\pi^2}{3} \frac{k_{\rm B}T}{\epsilon_f} which is at room temperature of order of magnitude 10^{-2} .

This explains the absence of an electronic contribution to the heat capacity as measured experimentally. Note that in this derivation \epsilon_f is often denoted by E_{\rm F} which is known as the Fermi energy.

In this notation, the electron heat capacity becomes: C_v= \frac{\pi^2}{3} k_{\rm B}^2TD(E_{\rm F}) and for free electrons : C_V = \frac{\pi^2}{2}k_{\rm B} \left( \frac{k_{\rm B}T}{E_{\rm F}} \right) = \frac{\pi^2}{2} k_{\rm B}\left( \frac{T}{T_{\rm F}} \right) using the definition for the Fermi energy with T_{\rm F} the Fermi temperature. For temperatures below both the Debye temperature T_{\rm D} and the Fermi temperature T_{\rm F} the heat capacity of metals can be written as a sum of electron and phonon contributions that are linear and cubic respectively: C_V=\gamma T +AT^3 .

The coefficient \gamma can be calculated and determined experimentally. We report this value below: The free electrons in a metal do not usually lead to a strong deviation from the Dulong–Petit law at high temperatures.

Since \gamma is linear in T and A is linear in T^3 , at low temperatures the lattice contribution vanishes faster than the electronic contribution and the latter can be measured. The deviation of the approximated and experimentally determined electronic contribution to the heat capacity of a metal is not too large. A few metals deviate significantly from this approximated prediction.

Measurements indicate that these errors are associated with the electron mass being somehow changed in the metal, for the calculation of the electron heat capacity the effective mass of an electron should be considered instead. For Fe and Co the large deviations are attributed to the partially filled d-shells of these transition metals, whose d-bands lie at the Fermi energy.

The alkali metals are expected to have the best agreement with the free electron model since these metals only one s-electron outside a closed shell. However even sodium, which is considered to be the closest to a free electron metal, is determined to have a \gamma more than 25 per cent higher than expected from the theory.

Certain effects influence the deviation from the approximation: The interaction of the conduction electrons with the periodic potential of the rigid crystal lattice is neglected. The interaction of the conduction electrons with phonons is also neglected. This interaction causes changes in the effective mass of the electron and therefore it affects the electron energy.

The interaction of the conduction electrons with themselves is also ignored. A moving electron causes an inertial reaction in the surrounding electron gas.

S(T)=-2k_{\rm B} \sum_k[f_k \ln f_k +(1-f_k) \ln(1-f_k)] where f_k is the Fermi–Dirac distribution f_k=\frac{1}{e^{\beta \omega_k}+1} with \omega_k=\sqrt{\epsilon_k^2+\Delta_k(T)^2} and \epsilon_k=E_K-\mu=\hbar^2\mathbf{k}^2/2m -\mu is the particle energy with respect to the Fermi energy \Delta_k(T) =-\sum_{kk'}u_{k'}v_{k'} the energy gap parameter where u_k and v_k represents the probability that a Cooper pair is occupied or unoccupied respectively. The heat capacity is given by C_v(T)=T\frac{\partial S(T)}{\partial T}=T\sum_k \frac{\partial S}{\partial f_k}\frac{\partial f_k}{\partial T} .

The last two terms can be calculated: \begin{align} \frac{\partial S}{\partial f_k} &=-2k_{\rm B} \ln\frac{f_k}{1-f_k}=2\frac{1}{T} \sqrt{\epsilon_k^2+\Delta_k(T)^2}\\ \frac{\partial f_k}{\partial T} &= \frac{1}{k_{\rm B} T^2} \frac{e^{\beta \omega_k}}{(e^{\beta \omega_k}+1)^2}\left( \sqrt{\epsilon_k^2+\Delta_k(T)^2}-T\frac{\partial}{\partial T} \sqrt{\epsilon_k^2+\Delta_k(T)^2} \right) \end{align} Substituting this in the expression for the heat capacity and again applying that the sum over \mathbf{k} in the reciprocal space can be replaced by an integral in \epsilon multiplied by the density of states D(E_{\rm F}) this yields: C_v(T)=\frac{2D(E_{\rm F})}{k_{\rm B} T^2}\int^\infty_{-\infty} \left[ \frac{e^{\frac{\sqrt{\epsilon_k^2+\Delta_k(T)^2}}{k_{\rm B} T}}}{(e^{\frac{\sqrt{\epsilon_k^2+\Delta_k(T)^2}}{k_{\rm B} T}}+1)^2} \left( \epsilon_k^2 + \Delta_k(T)^2 -\frac{T}{2} \frac{\partial}{\partial T} \Delta_k(T)^2 \right) \right] d\epsilon_k At the critical temperature T=T_c Below the critical temperature T For T>T_c it holds that \Delta_k(T)=0 and the electron heat capacity becomes: C_v(T)=\frac{4D(E_{\rm F})}{k_{\rm B} T^2}\int^\infty_{-\infty}\frac{e^{\beta \epsilon}}{(e^{\beta \epsilon}+1)^2} \epsilon^2 d\epsilon=\frac{\pi^2}{3}D(E_{\rm F})k_{\rm B}^2T This is just the result for a normal metal derived in the section above, as expected since a superconductor behaves as a normal conductor above the critical temperature. ==== Superconductors at T = T c ==== At the critical temperature the heat capacity is discontinuous. This discontinuity in the heat capacity indicates that the transition for a material from normal conducting to superconducting is a second order phase transition.

Text derived from https://en.wikipedia.org/w/index.php?oldid=1344503161 under CC BY-SA 4.0; modifications have been made.

Sources cited in this revision

No external citation was extracted for this revision. That is a statement about the source, not a claim that none exists.