End-to-end delay

End-to-end delay or one-way delay (OWD) refers to the time taken for a packet to be transmitted across a network from source to destination.

Uses your system voice; voice and rate in settings.

≈ 3 min read

Cite, export and learn8 citation formats · 8 exports · lesson and quiz

Names in other languages

No names in other languages are held for this entry yet.

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

End-to-end delay or one-way delay (OWD) refers to the time taken for a packet to be transmitted across a network from source to destination. It is a common term in IP network monitoring, and differs from round-trip time (RTT) in that only the path in one direction, from source to destination, is measured.

Measurement

The ping utility measures the RTT, that is, the time to go and come back to a host. Half the RTT is often used as an approximation of OWD but this assumes that the forward and back paths are the same in terms of congestion, number of hops, or quality of service (QoS). This is not always a good assumption. To avoid such problems, the OWD may be measured directly.

Direct

OWDs may be measured between two points A and B of an IP network through the use of synchronized clocks; A records a timestamp on the packet and sends it to B, which notes the receiving time and calculates the OWD as their difference. The transmitted packets need to be identified at the source and destination in order to avoid packet loss or packet reordering.

However, this method suffers from several limitations, such as requiring intensive cooperation between both parties, and the accuracy of the measured delay is subject to the synchronization precision. The Minimum-Pairs Protocol is an example by which several cooperating entities, A, B, and C, could measure OWDs between one of them and a fourth less cooperative one (e.g., between B and X).

Estimate

Transmission between two network nodes may be asymmetric, and the forward and reverse delays are not equal. Half the RTT value is the average of the forward and reverse delays and so may sometimes be used as an approximation to the end-to-end delay. The accuracy of such an estimate depends on the nature of the delay distribution in both directions.

As delays in both directions become more symmetric, the accuracy increases. The probability mass function (PMF) of absolute error, E, between the smaller of the forward and reverse OWDs and their average (i.e., RTT/2) can be expressed as a function of the network delay distribution as follows: \Pr(E = x) = \begin{cases}\displaystyle\sum_{i=0}^\infty f_i(a).f_i(b), &x=0,\\\displaystyle\sum_{i=0}^\infty f_i(a).f_{2x+i}(b) + \sum_{i=0}^\infty f_i(b).f_{2x+i}(a), &x>0,\end{cases} where a and b are the forward and reverse edges, and f y (z) is the PMF of delay of edge z (that is,

Delay components

End-to-end delay in networks comes from several sources including transmission delay, propagation delay, processing delay and queuing delay.

Sample delay calculations

Text derived from https://en.wikipedia.org/w/index.php?oldid=1337720774 under CC BY-SA 4.0; modifications have been made.

Words in each sectionEstimateEstimateEstimate: 181 words181DirectDirectDirect: 127 words127MeasurementMeasurementMeasurement: 70 words70Delay componentsDelay componentsDelay components: 18 words18
Words in each section. Measured from the stored article body; sections below the minimum are not plotted.

Provenance

snapshot enwiki-001337720774 · captured 2026-02-11 · ledger · version history

Cite this page as: encyclopegia.org, “End-to-end delay”, snapshot enwiki-001337720774. https://encyclopegia.org/a/end-to-end-delay

Sources cited in this revision

No external citation was extracted for this revision. That is a statement about the source, not a claim that none exists.