Fatigue testing

Uses your system voice; voice and rate in settings.

Snapshot

≈ 5 min read

Names in other languages

No names in other languages are held for this entry yet.

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

Fatigue test of the Airbus A380 wing (showing the wing deflected upwards superimposed on the unloaded wing). The wing was tested for a total of 47500 flights which is 2.5 times the number of flights in 25 years of operation. Each 16 hour flight took 11 minutes to simulate on the fatigue test rig. Fatigue testing is a specialised form of mechanical testing that is performed by applying cyclic loading to a coupon or structure. These tests are used either to generate fatigue life and crack growth data, identify critical locations or demonstrate the safety of a structure that may be susceptible to fatigue. Fatigue tests are used on a range of components from coupons through to full size test articles such as automobiles and aircraft. Fatigue tests on coupons are typically conducted using servo hydraulic test machines which are capable of applying large variable amplitude cyclic loads. Constant amplitude testing can also be applied by simpler oscillating machines. The fatigue life of a coupon is the number of cycles it takes to break the coupon. This data can be used for creating stress-life or strain-life curves. The rate of crack growth in a coupon can also be measured, either during the test or afterward using fractography.…

Fatigue test of the Airbus A380 wing (showing the wing deflected upwards superimposed on the unloaded wing). The wing was tested for a total of 47500 flights which is 2.5 times the number of flights in 25 years of operation. Each 16 hour flight took 11 minutes to simulate on the fatigue test rig. Fatigue testing is a specialised form of mechanical testing that is performed by applying cyclic loading to a coupon or structure. These tests are used either to generate fatigue life and crack growth data, identify critical locations or demonstrate the safety of a structure that may be susceptible to fatigue. Fatigue tests are used on a range of components from coupons through to full size test articles such as automobiles and aircraft. Fatigue tests on coupons are typically conducted using servo hydraulic test machines which are capable of applying large variable amplitude cyclic loads. Constant amplitude testing can also be applied by simpler oscillating machines. The fatigue life of a coupon is the number of cycles it takes to break the coupon. This data can be used for creating stress-life or strain-life curves. The rate of crack growth in a coupon can also be measured, either during the test or afterward using fractography. Testing of coupons can also be carried out inside environmental chambers where the temperature, humidity and environment that may affect the rate of crack growth can be controlled. Because of the size and unique shape of full size test articles, special test rigs are built to apply loads through a series of hydraulic or electric actuators. Actuators aim to reproduce the significant loads experienced by a structure, which in the case of aircraft, may consist of manoeuvre, gust, buffet and ground-air-ground (GAG) loading. A representative sample or block of loading is applied repeatedly until the safe life of the structure has been demonstrated or failures occur which need to be repaired. Instrumentation such as load cells, strain gauges and displacement gauges are installed on the structure to ensure the correct loading has been applied. Periodic inspections of the structure around critical stress concentrations such as holes and fittings are made to determine the time detectable cracks were found and to ensure any cracking that does occur, does not affect other areas of the test article. Because not all loads can be applied, any unbalanced structural loads are typically reacted out to the test floor through non-critical structure such as the undercarriage. Airworthiness standards generally require a fatigue test to be carried out for large aircraft prior to certification to determine their safe life. Small aircraft may demonstrate safety through calculations, although typically larger scatter or safety factors are used because of the additional uncertainty involved. Fatigue tests are used to obtain material data such as the rate of growth of a fatigue crack that can be used with crack growth equations to predict the fatigue life. These tests usually determine the rate of crack growth per cycle da/dN versus the stress intensity factor range \Delta K = K_\max - K_\min , where the minimum stress intensity factor K_\min corresponds to the minimum load for R > 0 and is taken to be zero for R\le 0 , and R is the stress ratio R= K_\min/K_\max . Standardised tests have been developed to ensure repeatability and to allow the stress intensity factor to be easily determined but other shapes can be used providing the coupon is large enough to be mostly elastic. In cases where crack initiation from subsurface inclusions dominates, extreme value theory may be used in determining the effect of the coupon size.

References

Text derived from https://en.wikipedia.org/w/index.php?oldid=1356357115 under CC BY-SA 4.0; modifications have been made.

Sources cited in this revision

12 named source(s) extracted from the cited revision. A source with no author is shown by its publication; nothing is invented.