Ferrari flat-12 engine

The Ferrari flat-12 engine family is a series of flat-12 DOHC petrol engines produced by Ferrari from 1964 to 1996.

Uses your system voice; voice and rate in settings.

≈ 6 min read

Cite, export and learn8 citation formats · 8 exports · lesson and quiz

Names in other languages

No names in other languages are held for this entry yet.

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

The Ferrari flat-12 engine family is a series of flat-12 DOHC petrol engines produced by Ferrari from 1964 to 1996. The first racing Ferrari flat-12, the Mauro Forghieri-designed Tipo 207, was introduced in the Ferrari 1512 F1 car in 1964.

Later flat-12 racing engines were used in Ferrari Formula One and sports racing cars from 1968 until 1980, including the 212 E Montagna, 312 B series, 312 PB and 312 T series. The roadgoing flat-12 engines were introduced with the 365 GT4 BB and were produced in various versions until the end of F512 M production in 1996.

Tipo F102A

The Tipo F102A engine was the first flat-12 cylinder configuration fitted in a Ferrari road car, the 1973-1976 365 GT4 BB. Design and development of the new engine was overseen by Ferrari engineer Giuliano de Angelis and Angelo Bellei. The F102A engine's was derived from the Tipo 001 Formula One engine as well as earlier Ferrari Colombo V12 engines.

The engine's displacement, bore & stroke, rods and pistons were the same as the Tipo 251 60° V12 Colombo engine powering the 365 GTB/4 Daytona it replaced. The F102A had two valves per cylinder and twin overhead camshafts per bank, although these were now belt driven, instead of by chain as on earlier Ferrari 12-cylinder engines.

Belt drive was chosen to reduce noise, improve reliability and reduce manufacturing and servicing costs. The engine fitted with two banks of two triple-choke Weber 40IF3C carburettors and an electronic Magneti Marelli "Dinoplex" ignition system. In contrast to both the Tipo 251 and the Tipo 001, the spark plugs enter the combustion chamber from the top, rather than the sides.

The block and cylinder heads were constructed from Silumin light alloy, with Borgo light alloy pistons, shrunk-in cast iron cylinder liners and a cross-plane, forged steel crankshaft. As was standard Ferrari practice, the crankshaft was machined from a single billet of steel, which was aged prior to machining in order to improve structural stability.

The engine was lubricated by a wet sump with a capacity of and twin oil filters. According to de Angelis and Bellei, the first prototype F102 A engine produced at 7,100 rpm and propelled the prototype to during testing.

Some Ferrari sales materials quote this 380 bhp figure, while others reported the production version of the F102 A engine produced at 7,500 rpm and of torque at 4,500 rpm. Figures reported in other factory and press publications vary, with the owner's manual reporting 344 PS (253 kW; 339 hp) at 7200 rpm.

Tipo F102B

In 1976 Ferrari launched a revised version of the BB, the BB 512. This car was equipped with a Tipo F102B flat-12 engine, based on the preceding F102A but enlarged to 4942 cc. Bore and stroke were now 82 mm x 78 mm and the compression ratio was increased to 9.2:1.

Camshaft timing was also altered. Ferrari initially claimed a peak power output of at 6800 rpm and of torque. Later Ferrari publications revised this to .

Despite the loss in peak power, the flatter torque curve of the 4.9 liter engine provided a smoother and more user friendly power delivery. The larger displacement engine also allowed Ferrari to meet more stringent pollution and noise regulations without losing performance.

A dry sump lubrication system was now used to prevent oil starvation and surge issues, which were exacerbated by the higher cornering forces generated by the BB 512's wider tires. The F102B engine was also used in 512 BB LM racing cars. In series 1 cars, the engines were modified with new pistons, camshafts and carburetors, resulting in a power output of approximately .

Series 2 cars also had a Lucas mechanical fuel injection system, fed by dual Turolla fuel pumps. In this form, the engine generated approximately

Tipo F110A

In 1981 the BB 512 was replaced by the BB 512i, powered by the Tipo F110A engine. This engine was based on the F102B but was now equipped with Bosch K-Jetronic fuel injection. It had the same dimensions and overall capacity as the F102B.

The fuel injection system allowed Ferrari to meet stricter emissions regulations. Overall power output was now at 6,000 rpm. The Dinoplex electronic ignition system now had a built-in rev limiter that activated at 6,600 rpm.

Tipo F113A/B/D/G

The Testarossa was introduced in 1984, replacing the BB 512i. It was equipped with the Tipo F113A engine. This engine was the first roadgoing Ferrari flat-12 engine with four valves per cylinder.

The power output was , making it the most powerful engine mounted on a production sports car at the time of its launch. The bore and stroke and 4942 cc cubic capacity was identical to the preceding F110A engine. The F113A was fitted with a Marelli Microplex MED120 electronic ignition system and Bosch K-Jetronic fuel injection.

Export versions for United States, Canada and Japan had catalytic converter and KE-Jetronic fuel injection. European versions got those features in 1986 and the revised engine was known as F113B. The 1991 512 TR was equipped with the Tipo F113D engine.

This was an upgraded version of the F113A in the Testarossa, maintaining the same cubic capacity of 4.9 L. Changes were made to the porting, with redesigned inlet plenums and larger valves providing more efficient fuel/air mix ingress, whilst the fuel injection and ignition system were changed to a combined Bosch Motronic M2.7 system. The engine was further improved with new shallow-skirt pistons and a modified crankshaft design.

This engine produced at 6,750 rpm and at 5,500 rpm. For the 1994 F512 M the engine was further upgraded and designated Tipo F113G. This engine had a lightened crankshaft, titanium alloy connecting rods, new pistons and a stainless steel low backpressure exhaust system.

The compression ratio increased to 10.4:1. The F113G produced at 6,750 rpm. The flat-12 production ceased with the F512 M, being replaced by the front-engined 550 Maranello which featured the new 65° V12 F133 engine.

See also

List of Ferrari engines

Text derived from https://en.wikipedia.org/w/index.php?oldid=1361618180 under CC BY-SA 4.0; modifications have been made.

Words in each sectionTipo F102ATipo F102ATipo F102A: 333 words333Tipo F113A/B/D/GTipo F113A/B/D/GTipo F113A/B/D/G: 283 words283Tipo F102BTipo F102BTipo F102B: 210 words210Tipo F110ATipo F110ATipo F110A: 81 words81See alsoSee alsoSee also: 25 words25
Words in each section. Measured from the stored article body; sections below the minimum are not plotted.

Provenance

snapshot enwiki-001361618180 · captured 2026-06-29 · ledger · version history

Cite this page as: encyclopegia.org, “Ferrari flat-12 engine”, snapshot enwiki-001361618180. https://encyclopegia.org/a/ferrari-flat-12-engine

Sources cited in this revision

15 named source(s) extracted from the cited revision. A source with no author is shown by its publication; nothing is invented.