Floppy disk controller

. The NEC D765AC FDC IC is the large dual in-line package at the top. A floppy disk controller (FDC) is a hardware component that directs and controls reading from and writing to a computer's floppy disk drive (FDD). It has evolved from a discrete set of components on one or more circuit boards to a special-purpose integrated circuit (IC or "chip") or a component thereof. An FDC is responsible for reading data presented from the host computer and converting it to the drive's on-disk format using one of a number of encoding schemes, like FM encoding (single density) or MFM encoding (double density), and reading those formats and returning it to its original binary values. Depending on the platform, data transfers between the controller and host computer would be controlled by the computer's own microprocessor, or an inexpensive dedicated microprocessor like the MOS 6507 or Zilog Z80. Early controllers required additional circuitry to perform specific tasks like providing clock signals and setting various options. Later designs included more of this functionality on the controller and reduced the complexity of the external circuitry; single-chip solutions were common by the later 1980s. By the 1990s, the floppy disk was increasingly giving way to hard drives, which required similar controllers.…

. The NEC D765AC FDC IC is the large dual in-line package at the top.]] A floppy disk controller (FDC) is a hardware component that directs and controls reading from and writing to a computer's floppy disk drive (FDD). It has evolved from a discrete set of components on one or more circuit boards to a special-purpose integrated circuit (IC or "chip") or a component thereof. An FDC is responsible for reading data presented from the host computer and converting it to the drive's on-disk format using one of a number of encoding schemes, like FM encoding (single density) or MFM encoding (double density), and reading those formats and returning it to its original binary values. Depending on the platform, data transfers between the controller and host computer would be controlled by the computer's own microprocessor, or an inexpensive dedicated microprocessor like the MOS 6507 or Zilog Z80. Early controllers required additional circuitry to perform specific tasks like providing clock signals and setting various options. Later designs included more of this functionality on the controller and reduced the complexity of the external circuitry; single-chip solutions were common by the later 1980s. By the 1990s, the floppy disk was increasingly giving way to hard drives, which required similar controllers. In these systems, the controller also often combined a microcontroller to handle data transfer over standardized connectors like SCSI and IDE that could be used with any computer. In more modern systems, the FDC, if present at all, is typically part of the many functions provided by a single super I/O chip. __TOC__ ==Interface to the floppy disk drive== A controller connects to one or more drives using a flat ribbon cable, 50 wires for 8" drives and 34 wires for 3.5" & 5.25" drives. A "universal cable" has four drive connectors, two each for 3.5" & 5.25" drives. In the IBM PC family and compatibles, a twist in the cable is used to distinguish disk drives by the socket to which they are connected. All drives are installed with the same drive select address set, and the twist in the cable interchanges the drive select lines at the socket. The drive that is at the far end of the cable would also have a terminating resistor installed to maintain signal quality. More detailed descriptions of the interface signals including alternative meanings are contained in manufacturer's specifications for drives or host controllers. When the controller and disk drive are assembled as one device, as it is the case with some external floppy disk drives, e.g., Commodore 1540 and USB floppy disk drives, the internal floppy disk drive and its interface are unchanged, while the assembled device presents a different interface such as IEEE-488, parallel port or USB. == 3-mode floppy drive == 4.3, provided with 3.5" 1.2 MB and 1440 KB formats.]] Primarily in Japan there are 3.5" high-density floppy drives that support three modes of disk formats instead of the normal two – 1440 KB (2 MB unformatted), 1.2 MB (1.6 MB unformatted) and 720 KB (1 MB unformatted). Originally, the high-density modes for 3.5" floppy drives in Japan only supported a capacity of 1.2 MB instead of the 1440 KB capacity that was used elsewhere. While the more common 1440 KB format spun at 300 rpm, the 1.2 MB formats instead spun at 360 rpm, thereby closely resembling the geometries of either the 1.2 MB format with 80 tracks, 15 sectors per track, and 512 bytes per sector previously found on 5.25" high-density floppy disks or the 1.2 MB format with 77 tracks, 8 sectors per track, and 1,024 bytes per sector previously found on 8" double-density floppy disks. Later Japanese floppy drives incorporated support for both high-density formats (as well as the double-density format), hence the name 3-mode. Some BIOSes have a configuration setting to enable this mode for floppy drives supporting it.

Text derived from https://en.wikipedia.org/w/index.php?oldid=1362286093 under CC BY-SA 4.0; modifications have been made.