gyrator

analog circuit

Uses your system voice; voice and rate in settings.

Q677197Snapshot

≈ 8 min read

Names in other languages

  • ltGiratorius
  • etGüraator
  • ItalianoGiratore
  • daGyrator
  • DeutschGyrator
  • Englishgyrator
  • Bahasa IndonesiaGirator
  • PolskiŻyrator

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

A gyrator is a passive, linear, lossless, two-port electrical network element proposed in 1948 by Bernard D. H. Tellegen as a hypothetical fifth linear element after the resistor, capacitor, inductor and ideal transformer. Unlike the four conventional elements, the gyrator is non-reciprocal.

Gyrators permit network realizations of two-(or-more)-port devices which cannot be realized with just the four conventional elements. In particular, gyrators make possible network realizations of isolators and circulators. Gyrators do not however change the range of one-port devices that can be realized.

Although the gyrator was conceived as a fifth linear element, its adoption makes both the ideal transformer and either the capacitor or inductor redundant. Thus the number of necessary linear elements is in fact reduced to three.

Circuits that function as gyrators can be built with transistors and op-amps using feedback. proposed symbol for his gyrator Tellegen invented a circuit symbol for the gyrator and suggested a number of ways in which a practical gyrator might be built. An important property of a gyrator is that it inverts the current–voltage characteristic of an electrical component or network.

In the case of linear elements, the impedance is also inverted.…

A gyrator is a passive, linear, lossless, two-port electrical network element proposed in 1948 by Bernard D. H. Tellegen as a hypothetical fifth linear element after the resistor, capacitor, inductor and ideal transformer. Unlike the four conventional elements, the gyrator is non-reciprocal.

Gyrators permit network realizations of two-(or-more)-port devices which cannot be realized with just the four conventional elements. In particular, gyrators make possible network realizations of isolators and circulators. Gyrators do not however change the range of one-port devices that can be realized.

Although the gyrator was conceived as a fifth linear element, its adoption makes both the ideal transformer and either the capacitor or inductor redundant. Thus the number of necessary linear elements is in fact reduced to three.

Circuits that function as gyrators can be built with transistors and op-amps using feedback. proposed symbol for his gyrator Tellegen invented a circuit symbol for the gyrator and suggested a number of ways in which a practical gyrator might be built. An important property of a gyrator is that it inverts the current–voltage characteristic of an electrical component or network.

In the case of linear elements, the impedance is also inverted. In other words, a gyrator can make a capacitive circuit behave inductively, a series LC circuit behave like a parallel LC circuit, and so on. It is primarily used in active filter design and miniaturization. v_2 = R i_1, v_1 = -R i_2, where R is the gyration resistance of the gyrator.

The gyration resistance (or equivalently its reciprocal the gyration conductance) has an associated direction indicated by an arrow on the schematic diagram. By convention, the given gyration resistance or conductance relates the voltage on the port at the head of the arrow to the current at its tail.

The voltage at the tail of the arrow is related to the current at its head by minus the stated resistance. Reversing the arrow is equivalent to negating the gyration resistance, or to reversing the polarity of either port. Although a gyrator is characterized by its resistance value, it is a lossless component.

From the governing equations, the instantaneous power into the gyrator is identically zero: P = v_1 i_1 + v_2 i_2 = (-R i_2) i_1 + (R i_1) i_2 \equiv 0. A gyrator is an entirely non-reciprocal device, and hence is represented by antisymmetric impedance and admittance matrices: Z = \begin{bmatrix} 0 & -R \\ R & 0 \end{bmatrix},\quad Y = \begin{bmatrix} 0 & G \\ -G & 0 \end{bmatrix},\quad G = \frac{1}{R}.

If the gyration resistance is chosen to be equal to the characteristic impedance of the two ports (or to their geometric mean if these are not the same), then the scattering matrix for the gyrator is S = \begin{bmatrix} 0 & -1 \\ 1 & 0 \end{bmatrix}, which is likewise antisymmetric. This leads to an alternative definition of a gyrator: a device which transmits a signal unchanged in the forward (arrow) direction, but reverses the polarity of the signal travelling in the backward direction (or equivalently, 180° phase-shifts the backward-travelling signal ).

The symbol used to represent a gyrator in one-line diagrams (where a waveguide or transmission line is shown as a single line rather than as a pair of conductors), reflects this one-way phase shift. As with a quarter-wave transformer, if one port of a gyrator is terminated with a linear load, then the other port presents an impedance inversely proportional to the impedance of that load: Z_\text{in} = \frac{R^2}{Z_\text{load}}.

A generalization of the gyrator is conceivable, in which the forward and backward gyration conductances have different magnitudes, so that the admittance matrix is Y = \begin{bmatrix} 0 & G_1 \\ -G_2 & 0 \end{bmatrix}. However, this no longer represents a passive device.

Magnetic circuit analogy

In the two-gyrator equivalent circuit for a transformer, described above, the gyrators may be identified with the transformer windings, and the loop connecting the gyrators with the transformer magnetic core. The electric current around the loop then corresponds to the rate-of-change of magnetic flux through the core, and the electromotive force (EMF) in the loop due to each gyrator corresponds to the magnetomotive force (MMF) in the core due to each winding.

The gyration resistances are in the same ratio as the winding turn-counts, but collectively of no particular magnitude. So, choosing an arbitrary conversion factor of r ohms per turn, a loop EMF V is related to a core MMF \mathcal{F} by V = r \mathcal{F}, and the loop current I is related to the core flux-rate \dot{\Phi} by I = \frac{1}{r} \frac{\partial}{\partial t} \Phi.

The core of a real, non-ideal, transformer has finite permeance \mathcal{P} (non-zero reluctance \mathcal{R} ), such that the flux and total MMF satisfy \Phi = \frac{\mathcal{F}}{\mathcal{R}} = \mathcal{P} \mathcal{F}, which means that in the gyrator loop I = \frac{\mathcal{P}}{r^2} \frac{\partial}{\partial t} V corresponding to the introduction of a series capacitor C = \frac{1}{r^2} \mathcal{P} in the loop. This is Buntenbach's capacitance–permeance analogy, or the gyrator–capacitor model of magnetic circuits.

Simulated inductor

A gyrator can be used to transform a load capacitance into an inductance. At low frequencies and low powers, the behaviour of the gyrator can be reproduced by a small op-amp circuit. This supplies a means of providing an inductive element in a small electronic circuit or integrated circuit.

Before the invention of the transistor, coils of wire with large inductance might be used in electronic filters. An inductor can be replaced by a much smaller assembly containing a capacitor, operational amplifiers or transistors, and resistors. This is especially useful in integrated circuit technology.

Z = R_L + j \omega L. From the diagram, the input impedance of the op-amp circuit is Z_\text{in} = (R_\text{L} + j \omega R_L R C) \parallel \left(R + \frac{1}{j \omega C}\right). With R L RC = L, it can be seen that the impedance of the simulated inductor is the desired impedance in parallel with the impedance of the RC circuit.

In typical designs, R is chosen to be sufficiently large while \omega RC \approx 1 such that the first term dominates; thus, the RC-circuit's effect on input impedance is negligible: Z_\text{in} \approx R_L + j \omega R_L R C. This is the same as a resistance R L in series with an inductance L = R L RC. There is a practical limit on the minimum value that R L can take, determined by the current output capability of the op-amp.

The impedance cannot increase indefinitely with frequency, and eventually the second term limits the impedance to the value of R.

Impedance inversion

In microwave circuits, impedance inversion can be achieved using a quarter-wave impedance transformer instead of a gyrator. The quarter-wave transformer is a passive device and is far simpler to build than a gyrator. Unlike the gyrator, the transformer is a reciprocal component. The transformer is an example of a distributed-element circuit.

Text derived from https://en.wikipedia.org/w/index.php?oldid=1355168208 under CC BY-SA 4.0; modifications have been made.

Sources cited in this revision

No external citation was extracted for this revision. That is a statement about the source, not a claim that none exists.