HD-MAC

Uses your system voice; voice and rate in settings.

Snapshot

≈ 7 min read

Names in other languages

No names in other languages are held for this entry yet.

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

HD-MAC (High Definition Multiplexed Analogue Components) was a broadcast television standard proposed by the European Commission in 1986, as part of Eureka 95 project. It belongs to the MAC - Multiplexed Analogue Components standard family. It is an early attempt by the EEC to provide high-definition television (HDTV) in Europe. It is a complex mix of analogue signal (based on the Multiplexed Analogue Components standard), multiplexed with digital sound, and assistance data for decoding (DATV). The video signal (1250 lines/50 fields per second in 16:9 aspect ratio, with 1152 visible lines) was encoded with a modified D2-MAC encoder. HD-MAC could be decoded by normal D2-MAC standard definition receivers, but no extra resolution was obtained and certain artifacts were visible. To decode the signal in full resolution a specific HD-MAC tuner was required .

HD-MAC (High Definition Multiplexed Analogue Components) was a broadcast television standard proposed by the European Commission in 1986, as part of Eureka 95 project. It belongs to the MAC - Multiplexed Analogue Components standard family. It is an early attempt by the EEC to provide high-definition television (HDTV) in Europe. It is a complex mix of analogue signal (based on the Multiplexed Analogue Components standard), multiplexed with digital sound, and assistance data for decoding (DATV). The video signal (1250 lines/50 fields per second in 16:9 aspect ratio, with 1152 visible lines) was encoded with a modified D2-MAC encoder. HD-MAC could be decoded by normal D2-MAC standard definition receivers, but no extra resolution was obtained and certain artifacts were visible. To decode the signal in full resolution a specific HD-MAC tuner was required . European standard definition digital broadcasts use 720×576i/25, meaning 25 interlaced frames measuring 720 pixels wide and 576 pixels high per second: odd lines (1, 3, 5 ...) are grouped to build the odd field, which is transmitted first, then it is followed by the even field containing lines 2, 4, 6... Thus, there are two fields in a frame, resulting in a field frequency of 25 × 2 = 50 Hz. The visible part of the video signal provided by an HD-MAC receiver was 1152i/25, which exactly doubles the vertical resolution of standard definition. The amount of information is multiplied by 4, considering the encoder started its operations from a 1440x1152i/25 sampling grid. Had the modern trend for square pixels applied, this would have yielded a 2048x1152 sampling grid. There was no such requirement in the standard, though, since CRT monitors don't need any extra scaling to be able to show non-square pixels. According to the specification, the sampling rate for the interlaced input to use was 72 MHz, resulting in 72 x 26.67 = 1920 horizontal samples. It was then reconverted to 1440 from within the sampled domain. The input signal often originated from sources previously sampled at only 54 MHz, for economical reasons, and therefore already containing no more than the analogue equivalent of 1440 samples per line. Ultimately, the starting point for BRE was a 1440x1152 sampling grid (twice the horizontal and vertical resolutions of digital SD), interlaced, at 25 fps. To improve horizontal resolution of the D2-MAC norm, only its bandwidth had to be increased. This was easily done as, unlike PAL, the sound is not sent on a sub-carrier, but multiplexed with the picture. However, to increase vertical bandwidth was more complex, as the line frequency had to stay at 15.625 kHz to be compatible with D2-MAC. This offered three choices: 50 frames per second with only 288 lines for fast moving scenes (20 ms mode) 25 frames per second with 576 lines for normally moving scenes (40 ms mode) 12.5 frames per second with all 1152 lines for slow motion (80 ms mode) As none of the three modes would have been sufficient, the choice during encoding was not made for the whole picture, but for little blocks of 16×16 pixels. The signal then contained hints (the DATV digital stream) that controlled which de-interlacing method the decoder should use. The 20 ms mode offered an improved temporal resolution, but the 80 ms was the only one that provided High spatial definition in the usual sense. The 40 ms mode threw away one the HD fields and reconstructed it in the receiver with the assistance of motion compensation data. Some indications were also provided in case of a whole frame movement (camera panning,..) to improve the quality of the reconstruction. The encoder could work in "Camera" operating mode, using the three coding modes, but also in "film" mode where the 20 ms coding mode was not used. The 80 ms mode took advantage of its reduced 12.5 fps frame rate to spread the contents of an HD frame over two SD frames, meaning four 20 ms fields = 80 ms, hence the name. But that was not enough, as a single HD frame contains the equivalent of 4 SD frames. This could have been "solved" by doubling the bandwidth of the D2-MAC signal, thus increasing the allowed horizontal resolution by the same factor. Instead, the standard D2-MAC channel bandwidth was preserved, and one pixel out of two was dropped from each line. This sub-sampling was done in a quincux pattern. Assuming pixels on a line independently numbered from 1 to 1440, only pixels 1, 3, 5... were retained from the first line, pixels 2, 4, 6... from the second, 1, 3, 5...again from the third, and so on. That way, information from all the columns of the HD frame were conveyed to the receiver. Each missing pixel was surrounded by 4 transmitted ones (except on the sides) and could be interpolated from them. The resulting 720 horizontal resolution was further truncated to the 697 samples per line limit of the D2-HDMAC video multiplex. As a consequence of those operations, a 4:1 reduction factor was achieved, allowing the high definition video signal to be transported in a standard D2-MAC channel. The samples retained by the BRE were assembled into a valid standard definition D2-MAC vision signal and finally converted to analogue for transmission. The modulation parameters were such that the independence of the samples was preserved. To fully decode the picture, the receiver had to sample the signal again and then read from the memory several times. The BRD (Bandwidth Restoration Decoder) in the receiver would then reconstruct a 1394x1152 sampling grid from it, under the control of the DATV stream, to be fed into its DAC. The final output was a 1250 (1152 visible) lines, 25 fps, interlaced, analogue HD video signal, with a 50 Hz field frequency.

External links

Multiplexed Analogue Components in "Analog TV Broadcast Systems" by Paul Schlyter ETSI specification of the D2-HDMAC/Packet system (ETS 300 352) HDTV programme production HDTV coverage of the Barcelona Olympic Games Analogue HDTV in europe (Includes description of EBU HD-MAC evaluation tests) 1152p50 CCD camera developed for Eureka 95 Richard Russel career in BBC (Section "High definition TV" talks about preservation of HD-MAC archives by the BBC) The hdtv demonstrations at expo 92 TVHD document including problems encountered when shooting "L'affaire Seznec" 50 Jahre HDTV und mehr: a documentary that chronicles HD-MAC and Eureka 95 development

Text derived from https://en.wikipedia.org/w/index.php?oldid=1371996468 under CC BY-SA 4.0; modifications have been made.

Sources cited in this revision

24 named source(s) extracted from the cited revision. A source with no author is shown by its publication; nothing is invented.