Hydraulic jump

A hydraulic jump is an abrupt increase in the depth of a fast-moving liquid stream in an open channel, which is accompanied by a decrease in speed.

Uses your system voice; voice and rate in settings.

Snapshot

≈ 9 min read

Names in other languages

No names in other languages are held for this entry yet.

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

A hydraulic jump is an abrupt increase in the depth of a fast-moving liquid stream in an open channel, which is accompanied by a decrease in speed. The jump appears as a wavy or turbulent region between the high-speed upstream flow and the slower downstream flow. A common example is the circular jump formed when a tap runs into a kitchen sink.

Hydraulic jumps occur below dam spillways and in rivers. Hydraulic jumps may be stationary, as below a dam, or they may propagate as surges along a stream, as in a tidal bore. Civil engineers design spillways and stilling basins to create hydraulic jumps that dissipate the mechanical energy of water flowing over dams.

A hydraulic jump can form only when the upstream flow moves faster than shallow-water waves, so that small disturbances to the flow cannot travel upstream. For speeds only slightly above the wave speed, the transition is a rolling wave. As the flow speed increases, the transition becomes more abrupt, until at high enough speeds the front breaks and curls upstream.

These regimes are characterized by the ratio of upstream speed to wave speed, which is called the Froude number. Hydraulic jumps also occur in stratified flows, including in the atmosphere and the oceans. In rivers, they can create both recreational whitewater features and dangerous recirculating currents.

History

on the Mississippi River, showing a pronounced hydraulic jump at its base.|alt=Photo of the overflow spillway and jump at Lower St. Anthony Falls, Minneapolis As early as 1504, Leonardo da Vinci described and sketched water flows now understood as hydraulic jumps in his Codex Leicester. The first experimental investigations of hydraulic jumps were published by Giorgio Bidone in 18201.

Jean-Baptiste Bélanger formulated the first modern theory of the hydraulic jump in 1841. Experimental and theoretical studies of hydraulic jumps continued during the second half of the 19th century, but Hager described Safranez’s 1927 work as the first systematic experimental investigation of the phenomenon.

Research in the 1930s established the importance of the Froude number for characterizing the flow in hydraulic jumps. Hydraulic works had used devices such as stepped cascades to reduce the energy of flowing water since antiquity.

In the early 20th century, hydraulic jumps, energy dissipators, and stilling basins became subjects of intensive study, and by the mid-20th century standard stilling-basin design guidance had been codified.

Stationary and moving hydraulic jumps

in Alaska showing a steep, turbulent front. The upstream water is relatively shallow and the fractional change in elevation is large.|alt=Photo of a tidal bore in Alaska Hydraulic jumps may also be classified according to whether the transition is stationary or propagates as a surge. A stationary hydraulic jump occurs at a fixed location.

Upstream of the jump, the flow is fast and shallow; downstream, it is slow and deep. In the transition zone, the water slows and deepens in an abrupt step or standing wave. Downstream of the jump, the flow is typically turbulent and choppy.

A moving hydraulic jump, or surge, is a steep or undulating wavefront that propagates along the stream. A positive surge is a sudden increase in water depth that propagates as a wave either upstream or downstream. For example, when a dam breaks, a steep wall of water rushes downstream, and in tidal bores, a surge propagates upstream as the tide comes in.

Tidal bores occur in rivers or narrow bays when the incoming tide travels upstream against the current. A tidal bore advancing into shallow upstream water typically shows a large and steep elevation difference, whereas a tidal bore entering deep upstream water may have a small elevation difference and an undulating wavefront.

In both cases, the bore moves at the speed characteristic of waves in water of the depth immediately behind the wavefront. In a frame of reference moving with a surge, the surge is equivalent to a stationary jump.

The Bélanger equation and the Froude number

The principles of conservation of mass and conservation of momentum lead to an equation relating the depths downstream and upstream of the jump. The equation, known as the Bélanger equation, agrees closely with both field and laboratory measurements. The Bélanger equation describes a hydraulic jump in a rectangular channel of uniform width, under idealized assumptions.

The flow upstream of the jump has depth h_1 and an average speed v_1 . Downstream of the jump, the depth and average speed are h_2 and v_2 (see figure). Drag forces from the surface below the jump are presumed to be negligible.

The liquid has a density \rho , and g is the gravitational acceleration. If the flow is steady, the mass flow rate into the jump equals the mass flow rate out of the jump.

Per unit width, this gives: \rho v_1 h_1 = \rho v_2 h_2 The momentum inflow and hydrostatic pressure force upstream must equal the momentum outflow and hydrostatic pressure force downstream, so that: \rho v_1^2h_1 + {1 \over 2} \rho gh_1^2 = \rho v_2^2h_2 + {1 \over 2} \rho gh_2^2 Combining these expressions gives the ratio h_2/h_1 : {h_2 \over h_1} =\frac{ \sqrt{1+{\frac{8v_1^2}{gh_1}}}-1}{2} This result is called the Bélanger equation. The change in depth for non-rectangular cross-sections has also been studied.

The Froude number

The ratio v_1 / \sqrt{gh_1} that appears in the Bélanger equation is called the Froude number of the upstream flow: \text{Fr}_1 = {v_1 \over \sqrt{gh_1}} The Froude number is dimensionless. In terms of the Froude number, the Bélanger equation is: {h_2 \over h_1} =\frac {2} If \text{Fr}_1 > 1 , the equation shows that h_2 > h_1 , corresponding to an increase in depth across the jump.

For \text{Fr}_1 , the equation gives h_2 , implying a decrease in depth, but this solution is not physically admissible because it would require an increase in mechanical energy across the jump, violating the second law of thermodynamics. For \text{Fr}_1 = 1 , the depth does not change. Thus, the hydraulic jump can occur only when \text{Fr}_1 > 1 .

The speed of a shallow-water gravity wave is \sqrt{gh_1} , so the condition \text{Fr}_1 > 1 is equivalent to an upstream speed greater than the wave speed. This situation is called supercritical flow. The flow downstream of the jump moves slower than water waves ( \text{Fr}_2 ) and is thus subcritical flow.

A hydraulic jump is always a transition from supercritical to subcritical flow.

Analogy to shock waves in compressible flow

In compressible-fluid dynamics, flow with speed greater than the speed of sound is termed supersonic, while flow with speed less than the speed of sound is subsonic. The ratio of flow speed to sound speed is the Mach number, Ma.

Across a shock wave, a supersonic flow (Ma > 1) abruptly changes to subsonic flow (Ma 1) to subcritical flow (Fr \text{head loss} = \frac{(h_2 - h_1)^3}{4 h_1 h_2} This equation also agrees closely with measurements. The head loss increases with the difference in downstream and upstream depth and therefore rises with the Froude number.

The following table summarizes the trend between depth change, energy dissipation, and jump characteristics with increasing Froude number. The ranges given for the jump characteristics are approximate and can overlap.

The length of the hydraulic jump ranges from approximately 4 times the downstream depth for weak jumps to approximately 6.2 times the downstream depth for steady and strong jumps.

Internal hydraulic jumps

Most hydraulic jumps discussed in open-channel flow occur at a free surface. In stratified fluids, analogous jumps can occur at an internal density interface rather than at the air–water boundary.

These internal hydraulic jumps are rapid transitions between internally supercritical and internally subcritical flow, meaning that the flow changes from faster than internal waves along the interface to slower than them. Internal jumps are often associated with strong mixing of the fluid layers.

Internal hydraulic jumps occur in a variety of geophysical settings, including two-layer flows over underwater sills and stratified atmospheric flow over mountains. In the atmosphere, they may form on the lee side of topography and are often discussed alongside mountain lee waves.

A well-documented example occurs in the lee of the Sierra Nevada in California, where cloud formations can make the jump visible.

Recreation and hazards

in Wales|alt=A raft encountering a hydraulic jump on a river in Wales Hydraulic jumps and the standing waves associated with them are used in whitewater recreation, including kayaking, canoeing, rafting, and river surfing. In artificial whitewater parks, in-stream structures are often designed to create hydraulic jumps for kayakers and other boaters.

Kayakers and surfers sometimes ride tidal bores up rivers. Hydraulic jumps can also pose serious hazards to recreational river users. Below sharp drops, and especially below low-head dams, a submerged hydraulic roller may form in which recirculating flow can trap boats, swimmers, and debris for extended periods.

In whitewater paddling, highly retentive holes are often called “keepers”. Low-head dams are sometimes described in safety literature as “drowning machines”.

Surface tension and pattern formation in thin-film jumps

A liquid jet striking a surface, as in a kitchen sink, creates a thin liquid film that spreads radially before undergoing a hydraulic jump. For laminar jets, the thin film and the hydraulic jump can be entirely smooth and steady. In 1993, Liu and Lienhard showed that surface tension sets the shape of these jumps.

Many subsequent studies have explored the role of surface tension in such jumps. When capillary instability appears, a jump can adopt complex non-circular patterns, including polygons, three- and four-leaf clovers, bow ties, and cat’s eyes.

See also

Diablo wind Drop structure Undular bore Weir

Text derived from https://en.wikipedia.org/w/index.php?oldid=1378044757 under CC BY-SA 4.0; modifications have been made.

References

  1. ↩Wikipedia “Hydraulic jump” revision 1378044757 · retrieved 2026-10-20 publication date (×1) · confidence 0.95 revision URL