HyperTransport
HyperTransport (HT), formerly known as Lightning Data Transport, is a technology for interconnection of computer processors.
≈ 5 min read
Names in other languages
No names in other languages are held for this entry yet.
Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.
HyperTransport (HT), formerly known as Lightning Data Transport, is a technology for interconnection of computer processors. It is a bidirectional serial/parallel high-bandwidth, low-latency point-to-point link that was introduced on April 2, 2001. The HyperTransport Consortium is in charge of promoting and developing HyperTransport technology.
HyperTransport is best known as the system bus architecture of AMD central processing units (CPUs) from Athlon 64 through AMD FX and the associated motherboard chipsets. HyperTransport has also been used by IBM and Apple for the Power Mac G5 machines, as well as a number of modern MIPS systems.
The current specification HTX 3.1 remained competitive for 2014 high-speed (2666 and 3200 MT/s or about 10.4 GB/s and 12.8 GB/s) DDR4 RAM and slower (around 1 GB/s similar to high end [[Solid-state drive#Standard card form factors|PCIe SSDs] ULLtraDIMM flash RAM) technology —a wider range of RAM speeds on a common CPU bus than any Intel front-side bus. Intel technologies require each speed range of RAM to have its own interface, resulting in a more complex motherboard layout but with fewer bottlenecks.
HTX 3.1 at 26 GB/s can serve as a unified bus for as many as four DDR4 sticks running at the fastest proposed speeds. Beyond that DDR4 RAM may require two or more HTX 3.1 buses diminishing its value as unified transport.
HyperTransport (HT), formerly known as Lightning Data Transport, is a technology for interconnection of computer processors. It is a bidirectional serial/parallel high-bandwidth, low-latency point-to-point link that was introduced on April 2, 2001. The HyperTransport Consortium is in charge of promoting and developing HyperTransport technology.
HyperTransport is best known as the system bus architecture of AMD central processing units (CPUs) from Athlon 64 through AMD FX and the associated motherboard chipsets. HyperTransport has also been used by IBM and Apple for the Power Mac G5 machines, as well as a number of modern MIPS systems.
The current specification HTX 3.1 remained competitive for 2014 high-speed (2666 and 3200 MT/s or about 10.4 GB/s and 12.8 GB/s) DDR4 RAM and slower (around 1 GB/s similar to high end PCIe SSDs ULLtraDIMM flash RAM) technology —a wider range of RAM speeds on a common CPU bus than any Intel front-side bus. Intel technologies require each speed range of RAM to have its own interface, resulting in a more complex motherboard layout but with fewer bottlenecks.
HTX 3.1 at 26 GB/s can serve as a unified bus for as many as four DDR4 sticks running at the fastest proposed speeds. Beyond that DDR4 RAM may require two or more HTX 3.1 buses diminishing its value as unified transport.
Packet-oriented
HyperTransport is packet-based, where each packet consists of a set of 32-bit words, regardless of the physical width of the link. The first word in a packet always contains a command field. Many packets contain a 40-bit address.
An additional 32-bit control packet is prepended when 64-bit addressing is required. The data payload is sent after the control packet. Transfers are always padded to a multiple of 32 bits, regardless of their actual length.
HyperTransport packets enter the interconnect in segments known as bit times. The number of bit times required depends on the link width. HyperTransport also supports system management messaging, signaling interrupts, issuing probes to adjacent devices or processors, I/O transactions, and general data transactions.
There are two kinds of write commands supported: posted and non-posted. Posted writes do not require a response from the target. This is usually used for high bandwidth devices such as uniform memory access traffic or direct memory access transfers.
Non-posted writes require a response from the receiver in the form of a "target done" response. Reads also require a response, containing the read data. HyperTransport supports the PCI consumer/producer ordering model.
Text derived from https://en.wikipedia.org/w/index.php?oldid=1359457528 under CC BY-SA 4.0; modifications have been made.