Interchange (road)

In the field of road transport, an interchange (American English) or a grade-separated junction (British English) is a road junction that uses grade separations to allow for the movement of traffic between two or more roadways or highways…

Uses your system voice; voice and rate in settings.

≈ 4 min read

Cite, export and learn8 citation formats · 8 exports · lesson and quiz

Names in other languages

No names in other languages are held for this entry yet.

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

In the field of road transport, an interchange (American English) or a grade-separated junction (British English) is a road junction that uses grade separations to allow for the movement of traffic between two or more roadways or highways, using a system of interconnecting roadways to permit traffic on at least one of the routes to pass through the junction without interruption from crossing traffic streams. It differs from a standard intersection, where roads cross at grade.

Interchanges are almost always used when at least one road is a controlled-access highway (freeway) or a limited-access highway (expressway), though they are sometimes used at junctions between surface streets.

T and Y interchanges

A full Y interchange (also known as a directional T interchange) is typically used when a three-way interchange is required for two or three highways interchanging in semi-parallel/perpendicular directions, but it can also be used in right-angle cases as well. Their connecting ramps can spur from either the right or left side of the highway, depending on the direction of travel and the angle.

Directional T interchanges use flyover/underpass ramps for both connecting and mainline segments, and they require a moderate amount of land and moderate costs since only two levels of roadway are typically used. Their name derives from their resemblance to the capital letter T, depending upon the angle from which the interchange is seen and the alignment of the roads that are interchanging.

It is sometimes known as the "New England Y", as this design is often seen in the northeastern United States, particularly in Connecticut. This type of interchange features directional ramps (no loops, or weaving right to turn left) and can use multilane ramps in comparatively little space.

Some designs have two ramps and the "inside" through road (on the same side as the freeway that ends) crossing each other at a three-level bridge. The directional T interchange is preferred to a trumpet interchange because a trumpet requires a loop ramp by which speeds can be reduced, but flyover ramps can handle much faster speeds.

The disadvantage of the directional T is that traffic from the terminating road enters and leaves on the passing lane, so the semi-directional T interchange (see below) is preferred. The interchange of Highway 416 and Highway 417 in Ontario, constructed in the early 1990s, is one of the few directional T interchanges, as most transportation departments had switched to the semi-directional T design.

As with a directional T interchange, a semi-directional T interchange uses flyover (overpass) or underpass ramps in all directions at a three-way interchange. However, in a semi-directional T, some of the splits and merges are switched to avoid ramps to and from the passing lane, eliminating the major disadvantage of the directional T. Semi-directional T interchanges are generally safe and efficient, though they do require more land and are costlier than trumpet interchanges.

Semi-directional T interchanges are built as two- or three-level junctions, with three-level interchanges typically used in urban or suburban areas where land is more expensive. In a three-level semi-directional T, the two semi-directional ramps from the terminating highway cross the surviving highway at or near a single point, which requires both an overpass and underpass.

In a two-level semi-directional T, the two semi-directional ramps from the terminating highway cross each other at a different point than the surviving highway, necessitating longer ramps and often one ramp having two overpasses. Highway 412 has a three-level semi-directional T at Highway 407 and a two-level semi-directional T at Highway 401.

Image:Knooppunt driehoek.png|Full Y interchange Image:California SR 85 and SR 87 Interchange.jpg|Complex T interchange of SR 85 and SR 87 in San Jose, California. File:Knooppunt halve ster.png|Semi-directional T interchange Image:Interchange-colour-img 0526.jpg|Two level semi-directional T interchange in Orbe, Switzerland.

File:Derry and 407.jpg|A parclo A4 interchange along Highway 407 on the Mississauga / Milton, Ontario, boundary File:Autobahn anschluss1.jpg|A parclo AB2, or folded-diamond interchange along Bundesautobahn 7 in Germany

Text derived from https://en.wikipedia.org/w/index.php?oldid=1373586107 under CC BY-SA 4.0; modifications have been made.

Provenance

snapshot enwiki-001373586107 · captured 2026-09-06 · ledger · version history

Cite this page as: encyclopegia.org, “Interchange (road)”, snapshot enwiki-001373586107. https://encyclopegia.org/a/interchange-road

Sources cited in this revision

31 named source(s) extracted from the cited revision. A source with no author is shown by its publication; nothing is invented.