Interfacial polymerization

Uses your system voice; voice and rate in settings.

Snapshot

≈ 6 min read

Names in other languages

  • EnglishInterfacial polymerization
  • TürkçeAra yüzey polimerizasyonu
  • mlഇന്റർഫേഷ്യൽ പോളിമറൈസേഷൻ

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

Interfacial polymerization is a type of step-growth polymerization in which polymerization occurs at the interface between two immiscible phases (generally two liquids), resulting in a polymer that is constrained to the interface. There are several variations of interfacial polymerization, which result in several types of polymer topologies, such as ultra-thin films, nanocapsules, and nanofibers, to name just a few. . Benzylamine reacts with acetyl chloride under Schotten-Baumann conditions to form N-benzylacetamide.

Interfacial polymerization is a type of step-growth polymerization in which polymerization occurs at the interface between two immiscible phases (generally two liquids), resulting in a polymer that is constrained to the interface. There are several variations of interfacial polymerization, which result in several types of polymer topologies, such as ultra-thin films, nanocapsules, and nanofibers, to name just a few. . Benzylamine reacts with acetyl chloride under Schotten-Baumann conditions to form N-benzylacetamide.

Mechanism

The most commonly used interfacial polymerization methods fall into 3 broad types of interfaces: liquid-solid interfaces, liquid-liquid interfaces, and liquid-in-liquid emulsion interfaces. In the liquid-liquid and liquid-in-liquid emulsion interfaces, either one or both liquid phases may contain monomers. There are also other interface categories, rarely used, including liquid-gas, solid-gas, and solid-solid. In a liquid-solid interface, polymerization begins at the interface, and results in a polymer attached to the surface of the solid phase. In a liquid-liquid interface with monomer dissolved in one phase, polymerization occurs on only one side of the interface, whereas in liquid-liquid interfaces with monomer dissolved in both phases, polymerization occurs on both sides. An interfacial polymerization reaction may proceed either stirred or unstirred. In a stirred reaction, the two phases are combined using vigorous agitation, resulting in a higher interfacial surface area and a higher polymer yield. In the case of capsule synthesis, the size of the capsule is directly determined by the stirring rate of the emulsion. Although interfacial polymerization appears to be a relatively straightforward process, there are several experimental variables that can be modified in order to design specific polymers or modify polymer characteristics. Some of the more notable variables include the identity of the organic solvent, monomer concentration, reactivity, solubility, the stability of the interface, and the number of functional groups present on the monomers. The identity of the organic solvent is of utmost importance, as it affects several other factors such as monomer diffusion, reaction rate, and polymer solubility and permeability. The number of functional groups present on the monomer is also important, as it affects the polymer topology: a di-substituted monomer will form linear chains whereas a tri- or tetra-substituted monomer forms branched polymers. Most interfacial polymerizations are synthesized on a porous support in order to provide additional mechanical strength, allowing delicate nano films to be used in industrial applications. In this case, a good support would consist of pores ranging from 1 to 100 nm. Free-standing films, by contrast, do not use a support, and are often used to synthesize unique topologies such as micro- or nanocapsules. In the case of polyurethanes and polyamides especially, the film can be pulled continuously from the interface in an unstirred reaction, forming "ropes" of polymeric film. As the polymer precipitates, it can be withdrawn continuously. It is interesting to note that the molecular weight distribution of polymers synthesized by interfacial polymerization is broader than the Flory–Schulz distribution due to the high concentration of monomers near the interfacial site. Because the two solutions used in this reaction are immiscible and the rate of reaction is high, this reaction mechanism tends to produce a small number of long polymer chains of high molecular weight. {\partial c_i\over\partial t} = {\partial\over\partial y}(D_i{\partial c_i\over\partial y}) + J_i in which c i is the molar concentration of functional groups in the ith component of a monomer or polymer, t is the elapsed time, y is a coordinate normal to the surface/interface, D i is the molecular diffusion coefficient of the functional groups of interest, and J i is the thermodynamic rate of reaction. Although precise, no analytical solution exists for this differential equation, and as such solutions must be found using approximate or numerical techniques. In the macrokinetic model, the progression of an entire system is predicted. One important assumption of the macrokinetic model is that each mass transfer process is independent, and can therefore be described by a local model. The macrokinetic model may be the most important, as it can provide feedback on the efficiency of the reaction process, important in both laboratory and industrial applications. More specific approaches to modeling interfacial polymerization are described by Ji and co-workers, and include modeling of thin-film composite (TFC) membranes, tubular fibers, hollow membranes, and capsules. These models take into account both reaction- and diffusion-controlled interfacial polymerization under non-steady-state conditions. One model is for thin film composite (TFC) membranes, and describes the thickness of the composite film as a function of time: t = -({E_0 \over B_0} + {A_0D_0 \over B_0^2} + {C_0A_0^2 \over B_0^2}) \ln(1-{X \over X_{max}})-{C_0 \over 2B_0}X^2 - ({D_0 \over B_0}+{C_0A_0 \over B_0^2})X Where A 0 , B 0 , C 0 , D 0 , and E 0 are constants determined by the system, X is the film thickness, and X max is the maximum value of film thickness, which can be determined experimentally. Another model for interfacial polymerization of capsules, or encapsulation, is also described: t = A_0{R_{min}}^5E_0I_4 + B_0{R_{min}}^4E_0I_3 + C_0{R_{min}}^2E_0I_2 + D_0{R_{min}}E_0I_1 Where A 0 , B 0 , C 0 , D 0 , E 0 , I 1 , I 2 , I 3 , and I 4 are constants determined by the system and R min is the minimum value of the inside diameter of the polymeric capsule wall. There are several assumptions made by these and similar models, including but not limited to uniformity of monomer concentration, temperature, and film density, and second-order reaction kinetics.

See also

Polymerization Interfacial polycondensation

Text derived from https://en.wikipedia.org/w/index.php?oldid=1352522127 under CC BY-SA 4.0; modifications have been made.

Provenance

snapshot enwiki-001352522127 · captured 1777910281.0 · version history

Cite this page as: encyclopegia.org, “Interfacial polymerization”, snapshot enwiki-001352522127. https://encyclopegia.org/a/interfacial-polymerization

Sources cited in this revision

Extracted from the cited revision's reference blocks; absent citations are not invented.