Isothermal process

Uses your system voice; voice and rate in settings.

Snapshot

≈ 9 min read

Names in other languages

No names in other languages are held for this entry yet.

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

An isothermal process is a type of thermodynamic process in which the temperature T of a system remains constant: ΔT = 0. This typically occurs when a system is in contact with an outside thermal reservoir, and a change in the system occurs slowly enough to allow the system to be continuously adjusted to the temperature of the reservoir through heat exchange (see quasi-equilibrium). In contrast, an adiabatic process is where a system exchanges no heat with its surroundings (Q = 0). Simply, we can say that in an isothermal process * T = \text{constant} * \Delta T = 0 * dT = 0 * For ideal gases only, internal energy \Delta U = 0 while in adiabatic processes: * Q = 0.

An isothermal process is a type of thermodynamic process in which the temperature T of a system remains constant: ΔT = 0. This typically occurs when a system is in contact with an outside thermal reservoir, and a change in the system occurs slowly enough to allow the system to be continuously adjusted to the temperature of the reservoir through heat exchange (see quasi-equilibrium). In contrast, an adiabatic process is where a system exchanges no heat with its surroundings (Q = 0). Simply, we can say that in an isothermal process T = \text{constant} \Delta T = 0 dT = 0 For ideal gases only, internal energy \Delta U = 0 while in adiabatic processes: Q = 0.

Etymology

The noun isotherm is derived from the Ancient Greek words ( ), meaning "equal", and ( ), meaning "heat". For an adiabatic process, in which no heat flows into or out of the gas because its container is well insulated, Q = 0. If there is also no work done, i.e. a free expansion, there is no change in internal energy. For an ideal gas, this means that the process is also isothermal. Thus, specifying that a process is isothermal is not sufficient to specify a unique process.

For the special case of a gas to which Boyle's law applies, the product pV (p for gas pressure and V for gas volume) is a constant if the gas is kept at isothermal conditions. The value of the constant is nRT, where n is the number of moles of the present gas and R is the ideal gas constant. In other words, the ideal gas law pV = nRT applies. Therefore: p = {n R T \over V} = {\text{constant} \over V} holds. The family of curves generated by this equation is shown in the graph in Figure 1.

Each curve is called an isotherm, meaning a curve at a same temperature T. Such graphs are termed indicator diagrams and were first used by James Watt and others to monitor the efficiency of engines. The temperature corresponding to each curve in the figure increases from the lower left to the upper right. W_{A\to B} = -\int_{V_A}^{V_B}p\,dV where p for gas pressure and V for gas volume.

For an isothermal (constant temperature T), reversible process, this integral equals the area under the relevant PV (pressure-volume) isotherm, and is indicated in purple in Figure 2 for an ideal gas. Again, p =  applies and with T being constant (as this is an isothermal process), the expression for work becomes: W_{A\to B} = -\int_{V_A}^{V_B}p\,dV = -\int_{V_A}^{V_B}\frac{nRT}{V}dV = -nRT\int_{V_A}^{V_B}\frac{1}{V}dV = -nRT\ln{\frac{V_B}{V_A}} In IUPAC convention, work is defined as work on a system by its surroundings.

If, for example, the system is compressed, then the work is done on the system by the surrounding so the work is positive and the internal energy of the system increases. Conversely, if the system expands (i.e., system surrounding expansion, so free expansions not the case), then the work is negative as the system does work on the surroundings. It is also worth noting that for ideal gases, if the temperature is held constant, the internal energy of the system U also is constant, and so ΔU = 0.

Since the first law of thermodynamics states that ΔU = Q + W in IUPAC convention, it follows that Q = −W for the isothermal compression or expansion of ideal gases. During isothermal expansion of an ideal gas, both and change along an isotherm with a constant product (i.e., constant T). Consider a working gas in a cylindrical chamber 1 m1 high and 1 m 2 area (so 1m 3 volume) at 400 K in static equilibrium. The surroundings consist of air at 300 K and 1 atm pressure (designated as ).

The working gas is confined by a piston connected to a mechanical device that exerts a force sufficient to create a working gas pressure of 2 atm (state ). For any change in state that causes a force decrease, the gas will expand and perform work on the surroundings. Isothermal expansion continues as long as the applied force decreases and appropriate heat is added to keep = 2 [atm·m 3 ] (= 2 atm × 1 m 3 ).

The expansion is said to be internally reversible if the piston motion is sufficiently slow such that at each instant during the expansion the gas temperature and pressure is uniform and conform to the ideal gas law. Figure 3 shows the relationship for = 2 [atm·m 3 ] for isothermal expansion from 2 atm (state ) to 1 atm (state ). The work done (designated W_{A\to B} ) has two components. First, expansion work against the surrounding atmosphere pressure (designated as ), and second, usable mechanical work (designated as ).

The output here could be movement of the piston used to turn a crank-arm, which would then turn a pulley capable of lifting water out of flooded salt mines. W_{A\to B} = -p\,V\left(\ln\frac{V_B}{V_A}\right) = -W_{p \Delta V} -W_{\rm mech} The system attains state ( = 2 [atm·m 3 ] with = 1 atm and = 2 m 3 ) when the applied force reaches zero. At that point, W_{A\to B} equals –140.5 kJ, and is –101.3 kJ. By difference, = –39.1 kJ, which is 27.9% of the heat supplied to the process (- 39.1 kJ / - 140.5 kJ).

This is the maximum amount of usable mechanical work obtainable from the process at the stated conditions. The percentage of is a function of and , and approaches 100% as approaches zero. To pursue the nature of isothermal expansion further, note the red line on Figure 3. The fixed value of causes an exponential increase in piston rise vs. pressure decrease. For example, a pressure decrease from 2 to 1.9 atm causes a piston rise of 0.0526 m. In comparison, a pressure decrease from 1.1 to 1 atm causes a piston rise of 0.1818 m.

Entropy changes

Isothermal processes are especially convenient for calculating changes in entropy since, in this case, the formula for the entropy change, ΔS, is simply \Delta S = \frac{Q_\text{rev}}{T} where Q rev is the heat transferred (internally reversible) to the system and T is absolute temperature. This formula is valid only for a hypothetical reversible process; that is, a process in which equilibrium is maintained at all times.

A simple example is an equilibrium phase transition (such as melting or evaporation) taking place at constant temperature and pressure. For a phase transition at constant pressure, the heat transferred to the system is equal to the enthalpy of transformation, ΔH tr , thus Q = ΔH tr . At any given pressure, there will be a transition temperature, T tr , for which the two phases are in equilibrium (for example, the normal boiling point for vaporization of a liquid at one atmosphere pressure).

If the transition takes place under such equilibrium conditions, the formula above may be used to directly calculate the entropy change \Delta S_\text{tr} = \frac{\Delta H_\text{tr}}{T_\text{tr}} . Another example is the reversible isothermal expansion (or compression) of an ideal gas from an initial volume V A and pressure P A to a final volume V B and pressure P B . As shown in Calculation of work, the heat transferred to the gas is Q = -W = n R T \ln{\frac{V_{\text{B}}}{V_{\text{A}}}} .

This result is for a reversible process, so it may be substituted in the formula for the entropy change to obtain \Delta S = n R \ln \frac{V_{\text{B}}}{V_{\text{A}}} . Since an ideal gas obeys Boyle's law, this can be rewritten, if desired, as \Delta S = n R \ln \frac{P_{\text{A}}}{P_{\text{B}}} . Once obtained, these formulas can be applied to an irreversible process, such as the free expansion of an ideal gas. Such an expansion is also isothermal and may have the same initial and final states as in the reversible expansion.

Since entropy is a state function (that depends on an equilibrium state, not depending on a path that the system takes to reach that state), the change in entropy of the system is the same as in the reversible process and is given by the formulas above. Note that the result Q = 0 for the free expansion can not be used in the formula for the entropy change since the process is not reversible. The difference between the reversible and irreversible is found in the entropy of the surroundings.

In both cases, the surroundings are at a constant temperature, T, so that ΔS sur  = − ; the minus sign is used since the heat transferred to the surroundings is equal in magnitude and opposite in sign to the heat Q transferred to the system. In the reversible case, the change in entropy of the surroundings is equal and opposite to the change in the system, so the change in entropy of the universe is zero. In the irreversible, Q = 0, so the entropy of the surroundings does not change and the change in entropy of the universe is equal to ΔS for the system.

Text derived from https://en.wikipedia.org/w/index.php?oldid=1376335989 under CC BY-SA 4.0; modifications have been made.

References

  1. ↩Wikipedia “Isothermal process” revision 1376335989 · retrieved 2026-10-20 area (×1) · confidence 0.95 revision URL