Loading gauge
≈ 23 min read
Names in other languages
No names in other languages are held for this entry yet.
Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.
between a train and the tunnel is often small. Pictured is a London Underground Northern line 1995 Stock train emerging from the tunnel north of Hendon Central station. A loading gauge is a diagram or physical structure that defines the maximum height and width of railway vehicles and their loads. The loading gauge is to ensure that rail vehicles can pass safely through tunnels and under bridges, and keep clear of platforms, trackside buildings and other structures. Classification systems vary between different countries, and loading gauges may vary across a network, even if the track gauge is uniform. The term loading gauge can also be applied to the maximum size of road vehicles in relation to tunnels, overpasses and bridges, and doors into automobile repair shops, bus garages, filling stations, residential garages, multi-storey car parks and warehouses. A related but separate gauge is the structure gauge, which sets limits to the extent that bridges, tunnels and other infrastructure can encroach on rail vehicles. The difference between these two gauges is called the clearance. The specified amount of clearance makes allowance for the oscillation of rail vehicles at speed.
between a train and the tunnel is often small. Pictured is a London Underground Northern line 1995 Stock train emerging from the tunnel north of Hendon Central station. A loading gauge is a diagram or physical structure that defines the maximum height and width of railway vehicles and their loads. The loading gauge is to ensure that rail vehicles can pass safely through tunnels and under bridges, and keep clear of platforms, trackside buildings and other structures. Classification systems vary between different countries, and loading gauges may vary across a network, even if the track gauge is uniform. The term loading gauge can also be applied to the maximum size of road vehicles in relation to tunnels, overpasses and bridges, and doors into automobile repair shops, bus garages, filling stations, residential garages, multi-storey car parks and warehouses. A related but separate gauge is the structure gauge, which sets limits to the extent that bridges, tunnels and other infrastructure can encroach on rail vehicles. The difference between these two gauges is called the clearance. The specified amount of clearance makes allowance for the oscillation of rail vehicles at speed.
Overview
utilises differing loading gauges: a Metropolitan line S Stock sub-surface train (left) passes a Piccadilly line 1973 Stock tube train (right). The loading gauge governs the size of passenger carriages, goods wagons (freight cars) and shipping containers that can travel on the relevant section of railway track. It varies between rail systems around the world and can even vary within a single railway system. Over time, there has been a trend towards less restrictive loading gauges and greater standardization of them. Some older systems and lines have had their structure gauges expanded by raising bridges, increasing the height and width of tunnels and making other necessary alterations. Containerisation, and a trend towards larger shipping containers, has led rail operators to increase loading and structure gauges to compete with road haulage. The term "loading gauge" can also refer to a physical structure, sometimes using electronic detectors using light beams on an arm or gantry placed over the exit lines of goods yards or at the entry point to a restricted part of a network. The devices ensure that loads stacked on open or flat wagons stay within the height/shape limits of the line's bridges and tunnels, and prevent out-of-gauge rolling stock entering a stretch of line with a smaller loading gauge. Compliance with a loading gauge can be checked using a clearance car. In the past, they were simple wooden frames or physical feelers mounted on rolling stock. More recently, laser beams have been used. The loading gauge is the maximum size of rolling stock. It is distinct from the minimum structure gauge, which sets limits to the size of bridges and tunnels on a rail line, allowing for engineering tolerances and the motion of rail vehicles. The difference between the two is called the clearance. The terms "dynamic envelope" or "kinematic envelope", which include factors such as suspension travel, overhang on curves (at both ends and middle) and lateral motion on the track, are sometimes used in place of loading gauge. Railway platform height is also a consideration for the loading gauge of passenger trains. Where the two are not directly compatible, stairs may be required, which will increase loading times. Where long carriages are used at a curved platform, there will be gaps between the platform and the carriage door, causing risk. Problems increase where trains of several different loading gauges and vehicle floor heights use (or even must pass through) the same platform. The size of load that can be carried on a railway of a particular gauge is also influenced by the design of the rolling stock. Low-deck rolling stock can sometimes be used to carry taller shipping containers on lower gauge lines although their low-deck rolling stock cannot then carry as many containers. Rapid transit (metro) railways generally have a smaller loading gauge, which reduces the cost of tunnel construction. Those systems have to use their own specialised rolling stock.
History
The loading gauge on the main lines of Great Britain, most of which were built before 1900, is generally smaller than in other countries. In mainland Europe, the slightly larger Berne gauge (Gabarit passe-partout international, PPI) was agreed to in 1913 and came into force in 1914. As a result, British trains have noticeably and considerably smaller loading gauges and, for passenger trains, smaller interiors, despite the track being standard gauge, which is in line with much of the world. This often results in increased costs for purchasing new trainsets or locomotives as they must be specifically designed for the existing British network, rather than being purchased "off-the-shelf". For example, the new trains for HS2 have a 50% premium applied to the "classic compatible" sets that will be "compatible" with the current (or "classic") rail network loading gauge as well as the HS2 line. The "classic compatible" trainsets will cost £40 million per trainset whereas the HS2-only stock (built to European loading gauge and only suitable to operate on HS2 lines) will cost £27M per trainset despite the HS2-only stock being physically larger. It was recognized even during the nineteenth century that this would pose problems and countries whose railroads had been built or upgraded to a more generous loading gauge pressed for neighboring countries to upgrade their own standards. This was particularly true in continental Europe where the Nordic countries and Germany with their relatively generous loading gauge wanted their cars and locomotives to be able to run throughout the standard gauge network without being limited to a small size. France, which at the time had the most restrictive loading gauge ultimately compromised giving rise to Berne gauge which came into effect just before World War I. Military railways were often built to particularly high standards, especially after the American Civil War and the Franco-Prussian War showed the importance of railroads in military deployment as well as mobilization. The German Empire was particularly active in the construction of military railways which were often built with great expense to be as flat, straight and permissive in loading gauge as possible while bypassing major urban areas, making those lines of little use to civilian traffic, particularly civilian passenger traffic. However, all those aforementioned factors have in some cases led to the subsequent abandoning of those railroads. The loading gauge affected tank design, with the 1945 British Centurion tank the first British tank allowed to exceed the restricted British loading gauge. The 1944 German Tiger II tank had to be changed to narrower transport tracks instead of battle tracks for transport by rail.
Standard loading gauges for standard track gauge lines
International Union of Railways (UIC) Gauge
The International Union of Railways (UIC) has developed a standard series of loading gauges named A, B, B+ and C. PPI – the predecessor of the UIC gauges had the maximum dimensions with an almost round roof top. UIC A: The smallest (slightly larger than PPI gauge). Maximum dimensions . UIC B: Slightly larger than the UIC on the roof level. Maximum dimensions . UIC B+: New structures in France are being built to UIC B+. Up to has a shape to accommodate tractor-trailers loaded with ISO containers. UIC C: The Central European gauge. In Germany and other central European countries, the railway systems are built to UIC C gauges, sometimes with an increment in the width, allowing Scandinavian trains to reach German stations directly, originally built for Soviet freight cars. Maximum dimensions .
Europe
European standards
In the European Union, the UIC directives were supplanted by ERA Technical Specifications for Interoperability (TSI) of European Union in 2002, which has defined a number of recommendations to harmonize the train systems. The TSI Rolling Stock (2002/735/EC) has taken over the UIC Gauges definitions defining Kinematic Gauges with a reference profile such that Gauges GA and GB have a height of (they differ in shape) with Gauge GC rising to allowing for a width of of the flat roof. All cars must fall within an envelope of wide on a radius curve. The TGVs, which are wide, fall within this limit. The designation of a GB+ loading gauge refers to the plan to create a pan-European freight network for ISO containers and trailers with loaded ISO containers. These container trains (piggy-back trains) fit into the B envelope with a flat top so that only minor changes are required for the widespread structures built to loading gauge B on continental Europe. A few structures on the British Isles were extended to fit with GB+ as well, where the first lines to be rebuilt start at the Channel Tunnel. Owing to their historical legacies, many member states' railways do not conform to the TSI specification. For example, Britain's role at the forefront of railway development in the 19th century has condemned it to the small infrastructure dimensions of that era. Conversely, the s of countries that were satellites of the former Soviet Union are much larger than the TSI specification. Other than for GB+, they are not likely to be retrofitted, given the enormous cost and disruption that would be entailed.
Double-decker carriages
double-decker Intercity train railways A specific example of the value of these loading gauges is that they permit double decker passenger carriages. Although mainly used for suburban commuter lines, France is notable for using them on its high speed TGV services: the SNCF TGV Duplex carriages are high, the Netherlands, Belgium and Switzerland feature large numbers of double decker intercity trains as well. In Germany the Bombardier Twindexx was introduced in InterCity service in December 2015.
Great Britain
Great Britain has (in general) the most restrictive loading gauge (relative to track gauge) in the world. The gauge is a legacy of the British railway network being the world's oldest, and of having been built by a large number of different private companies, each with different standards for the width and height of trains. After nationalisation, a standard static gauge W5 was defined in 1951 that would virtually fit everywhere in the network. The W6 gauge is a refinement of W5, and the W6a changed the lower body to accommodate third-rail electrification. While the upper body is rounded for W6a with a static curve, there is an additional small rectangular notch for W7 to accommodate the transport of ISO containers, and the W8 loading gauge has an even larger notch spanning outside of the curve to accommodate the transport of ISO containers. While W5 to W9 are based on a rounded roof structure, those for W10 to W12 define a flat line at the top and, instead of a strict static gauge for the wagons, their sizes are derived from dynamic gauge computations for rectangular freight containers. and Ryde Esplanade, which has been reduced several times to prevent flooding, trains on the Island Line, Isle of Wight require short loading gauges to traverse the tunnel. Approaching the tunnel is a Class 484 EMU, built from ex-London Underground D78 Stock units. Network Rail uses a W loading gauge classification system of freight transport ranging from W6A (smallest) through W7, W8, W9, W9Plus, W10, W11 to W12 (largest). The definitions assume a common "lower sector structure gauge" with a common freight platform at above rail. In addition, gauge C1 provides a specification for standard coach stock, gauge C3 for longer Mark 3 coaching stock, gauge C4 for Pendolino stock and gauge UK1 for high-speed rail. There is also a gauge for locomotives. The size of container that can be conveyed depends both upon the size of the load that can be conveyed and the design of the rolling stock. W6A: Available over the majority of the British rail network. W8: Allows standard high shipping containers to be carried on standard wagons. W9: Allows high Hi-Cube shipping containers to be carried on "Megafret" wagons that have lower deck height with reduced capacity. At wide, it allows for wide Euro shipping containers, which are designed to carry Euro-pallets efficiently W10: Allows high Hi-Cube shipping containers to be carried on standard wagons and also allows wide Euro shipping containers. Larger than UIC A. W11: Little used but larger than UIC B. W12: Slightly wider than W10 at to accommodate refrigerated containers. Recommended clearance for new structures, such as bridges and tunnels. UIC GC: Channel Tunnel and Channel Tunnel Rail Link to London; with proposals to upgrade the Midland Main Line northwards from London to GB+ standards. A strategy was adopted in 2004 to guide enhancements of loading gauges and in 2007 the freight route utilisation strategy was published. That identified a number of key routes where the loading gauge should be cleared to W10 standard and, where structures are being renewed, that W12 is the preferred standard. Height and width of containers that can be carried on GB gauges (height by width). Units as per source material. W9: by W10: by W11: by W12: by
Tube lines
The City and South London Railway was built with tunnels of only diameter. They were later enlarged for the Northern line to . The Central line has tunnels of , increasing on curves and narrowing to near stations. This makes Central line trains unique on the London Underground because although the rolling stock's loading gauge is the same as the other Tube lines, the smaller tunnels require the positive conductor rail to be higher than on all other lines. A Parliamentary committee headed by James Stansfeld then reported on 23 May 1892, "The evidence submitted to the Committee on the question of the diameter of the underground tubes containing the railways has been distinctly in favour of a minimum diameter of ". After that, all tube lines were at least that size. Piccadilly line with tunnels of Victoria line with tunnels of ; enlarged to reduce air friction. Glasgow Subway with tunnels of and a unique track gauge of only . Tyne and Wear Metro with tunnels of ; built to mainline rail network standards.
Sweden
The Swedish Transport Administration (Trafikverket) has largely replaced static reference profiles with kinematic reference profiles. The two main standards are SE-A and SE-C. The SE-B profile has been withdrawn, as all track has been upgraded to at least SE-A. SE-C is required for all new construction and, when economically viable, during upgrades. Some SE-A track has been partially upgraded to SE-C and accommodates profiles such as P/C 450 (P/C 447) and GC or loads such as SECU containers. Both SE-A and SE-C are defined for straight track, with the corresponding structure gauge. On curved track, the structure gauge is widened to allow the 24-metre reference vehicle to pass. By European standards, SE-C is unusually large, permitting vehicles up to 24 metres long and almost 4 metres wide. However, vehicles with softer suspension that allows greater lateral movement must be narrower to remain within the kinematic reference profile.
Netherlands
In the Netherlands, a similar shape to the UIC C is used that rises to in height. The trains are wider allowing for width similar to Sweden. About one third of the Dutch passenger trains use bilevel rail cars. However, Dutch platforms are much higher than Swedish ones.
Channel Tunnel
Channel Tunnel:
North America
Freight
The American loading gauge for freight cars on the North American rail network is generally based on standards set by the Association of American Railroads (AAR) Mechanical Division. The most widespread standards are AAR Plate B and AAR Plate C, but higher loading gauges have been introduced on major routes outside urban centers to accommodate rolling stock that makes better economic use of the network, such as auto carriers, hi-cube boxcars, and double-stack container loads. The maximum width of on (AAR Plate B), (AAR Plate C) and all other truck centers (of all other AAR Plates) are on a radius or 13° curve. In all cases of the increase of truck centers, the decrease of width is covered by AAR Plates D1 and D2. Listed here are the maximum heights and widths for cars. However, the specification in each AAR plate shows a car cross section that is chamfered at the top and bottom, meaning that a compliant car is not permitted to fill an entire rectangle of the maximum height and width. Technically, AAR Plate B is still the maximum height and truck center combination and the circulation of AAR Plate C is somewhat restricted. The prevalence of excess-height rolling stock, at first ~ piggybacks and hicube boxcars, then later autoracks, airplane-parts cars, and flatcars for hauling Boeing 737 fuselages, as well as high double-stacked containers in container well cars, has been increasing. This means that most, if not all, lines are now designed for a higher loading gauge. The width of these extra-height cars is covered by AAR Plate D1. All the Class I rail companies have invested in longterm projects to increase clearances to allow double stack freight. The mainline North American rail networks of the Union Pacific, the BNSF, the Canadian National, and the Canadian Pacific, have already been upgraded to AAR Plate K. This represents over 60% of the Class I rail network. File:Boeing 737 fuselage train hull 3473.jpg|Boeing 737 Next Generation fuselage being transported by rail on a flatcar File:DTTX 724681 20050529 IL Rochelle.jpg|Double-stack container service requires the highest loading gauge in common use in North America. File:ETTX 905721 20050529 IL Rochelle.jpg|A Norfolk Southern autorack on a TTX flatcar also requires the highest loading gauge in common use in North America. File:Santa_Fe_TOFC_(Trailer_on_Flat_Car)_(10589289363).jpg|A Santa Fe semi-trailer carried on a flatcar as part of a TOFC train.
Boston (MBTA)
The Massachusetts Bay Transportation Authority's (MBTA) rapid transit system is composed of four unique subway lines; while all lines are standard gauge, inconsistencies in loading gauge, electrification, and platform height prevent trains on one line from being used on another. The first segment of the Green Line (known as the Tremont Street subway) was constructed in 1897 to take the streetcars off Boston's busy downtown streets. When the Blue Line opened in 1904, it only ran streetcar services; the line was converted to rapid transit in 1924 due to high passenger loads, but the tight clearances in the tunnel under the Boston Harbor required narrower and shorter rapid transit cars. The Orange Line was originally built in 1901 to accommodate heavy rail transit cars of higher capacity than streetcars. The Red Line was opened in 1912, designed to handle what were for a time the largest underground transit cars in the world.
Los Angeles (LACMTA)
The Los Angeles Metro Rail system is an amalgamation of two former constituent companies, the Los Angeles County Transportation Commission and the Southern California Rapid Transit District; both of those companies were responsible for planning the initial system. It is composed of two heavy rail subway lines and several light rail lines with subway sections; while all lines are standard gauge, inconsistencies in electrification and loading gauge prohibit the light rail trains from operating on the heavy rail lines, and vice versa. The LACTC-planned Blue Line was opened in 1990 and partially operates on the route of the Pacific Electric interurban railroad line between downtown Los Angeles and Long Beach, which used overhead electrification and street-running streetcar vehicles. The SCRTD-planned Red Line (later split into the Red and Purple lines) was opened in 1993 and was designed to handle high-capacity heavy rail transit cars that would operate underground. Shortly after the Red Line began operations, the LACTC and the SCRTD merged to form the LACMTA, which became responsible for planning and construction of the Green, Gold, Expo, and K lines, as well as the D Line Extension and the Regional Connector.
Broad gauge
5 ft and Russian gauge
In Finland, rail cars can be up to wide with a permitted height from on the sides to in the centre. The track gauge is , differing from the Russian track gauge. The Russian loading gauges are defined in standard GOST 9238 (ГОСТ 9238–83, ГОСТ 9238–2013) with the current 2013 standard named "Габариты железнодорожного подвижного состава и приближения строений" (construction of rolling stock clearance diagrams [official English title]). It was accepted by the Interstate Council for Standardization, Metrology and Certification to be valid in Russia, Belarus, Moldova, Ukraine, Uzbekistan and Armenia. Loading gauge is generally wider than Europe, but with many exception standards. T: standard loading gauge T: 5,300 mm height, 3,750 mm width T c : 5,200 mm height, 3,750 mm width: for tank and dumper cars T pr : 5,300 mm height, 3,500 mm width: extra out-of-gauge cargo load for main tracks 1-T: guaranteed loading gauge for all ex-USSR lines including old tunnels. 1-T: 5,300 mm height, 3,400 mm width VM: for international stock for 1435 mm lines, standards for different lines 0-VM: 4,650 mm height, 3,250 mm width 1-VM: 4,700 mm height, 3,400 mm width 02-VM: 4,650 mm height, 3,150 mm width 03-VM: 4,280 mm height, 3,150 mm width The standard defines static envelopes for trains on the national network as T, T c and T pr . The static profile 1-T is the common standard on the complete 1520 mm rail network including the CIS and Baltic states. The structure clearance is given as S, S p and S 250 . There is a tradition that structure clearance is much bigger than the common train sizes. For international traffic, the standard references the kinematic envelope for GC and defines a modified GC ru for its high-speed trains. For other international traffic, there are 1-T, 1-VM, 0-VM, 02-VM and 03-VM st /03-VM k for the trains and 1-SM for the structure clearance. The main static profile T allows for a maximum width of rising to a maximum height of . The profile T c allows that width only at a height of , requiring a maximum of below , which matches with the standard for train platforms (with a height of ). The profile T pr has the same lower frame requirement but reduces the maximum upper body width to . The more universal profile 1-T has the complete body at a maximum width of still rising to a height of . Exceptions shall be double-stacking, maximum height shall be or . The structure gauge S requires buildings to be placed at minimum of from the track centreline. Bridges and tunnels must have a clearance of at least wide and high. The structure gauge S p for passenger platforms allows only above (the common platform height) requiring a width of below that line. The exceptions shall be double-stacking, minimum overhead wiring height must be (for maximum vehicle height of ) or (for maximum vehicle height of ). The main platform is defined to have a height of at a distance of from the center of the track to allow for trains with profile T. Low platforms at a height of may be placed at from the center of the track. A medium platform is a variant of the high platform but at a height of . The latter matches with the TSI height in Central Europe. In the earlier standard from 1983, the profile T would only be allowed to pass low platforms at while the standard high platform for cargo and passenger platforms would be placed no less than from the center of the track. That matches with the T c , T pr and the universal 1-T loading gauge. gauge = width (brakevan mirrors) = width (brakevan body) = height = length = (carriage) gauge = Lyn (locomotive) over headstocks length = width = height = Passenger length = width = wide, width over steps = height = File:BS Ladelehre Westbahnhof.JPG|German equipment outline gauge File:Lademass.jpg|Template to check if the load is exactly within the loading gauge File:Loading gauge at Moccone.jpg|Equipment outline gauge at Moccone File:Loading Gauge Eritrea.jpg|Eritrean loading gauge
See also
Berne gauge Bridge Clearance car Clearance space Cut Platform gap Railway platform height Ride height Structure gauge Tunnel
References
External links
2002/732/EC: Commission Decision of 30 May 2002 concerning the technical specification for interoperability relating to the infrastructure subsystem of the trans-European high-speed rail system Loading Gauges at The Self Site Norfolk Southern Railcar Guide & Fleet Specifications Railway industrial Clearance Association British Track Gauge & Loading Gauge Railway line clearances and car dimensions including weight limitations of railroads in the United States, Canada, Mexico and Cuba. AAR plates with UIC AAR "plate" loading gauge diagrams compared to UIC (pdf & Autocad)
Text derived from https://en.wikipedia.org/w/index.php?oldid=1364515959 under CC BY-SA 4.0; modifications have been made.