LPDDR

Uses your system voice; voice and rate in settings.

Snapshot

≈ 6 min read

Names in other languages

No names in other languages are held for this entry yet.

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

Low-Power Double Data Rate (LPDDR) is a type of synchronous dynamic random-access memory (SDRAM) designed to use less power than conventional memory. It is commonly used in smartphones, tablet computers, and laptops, where reducing power consumption is important for battery life. For this reason, earlier versions of the technology were also known as Mobile DDR. LPDDR differs from standard DDR SDRAM in both design and features, with changes that make it more suitable for mobile devices. Unlike DDR, which is typically installed in removable modules, LPDDR is usually soldered directly onto the device's motherboard to conserve space and improve efficiency. Although LPDDR uses a generational naming convention similar to that of DDR memory (such as LPDDR4 and DDR4), the two follow separate development standards, and the version numbers do not indicate that they share the same technologies. The LPDDR standard is developed and maintained by the JEDEC Solid State Technology Association.

Low-Power Double Data Rate (LPDDR) is a type of synchronous dynamic random-access memory (SDRAM) designed to use less power than conventional memory. It is commonly used in smartphones, tablet computers, and laptops, where reducing power consumption is important for battery life. For this reason, earlier versions of the technology were also known as Mobile DDR. LPDDR differs from standard DDR SDRAM in both design and features, with changes that make it more suitable for mobile devices. Unlike DDR, which is typically installed in removable modules, LPDDR is usually soldered directly onto the device's motherboard to conserve space and improve efficiency. Although LPDDR uses a generational naming convention similar to that of DDR memory (such as LPDDR4 and DDR4), the two follow separate development standards, and the version numbers do not indicate that they share the same technologies. The LPDDR standard is developed and maintained by the JEDEC Solid State Technology Association.

Bus width

In contrast with standard SDRAM, used in stationary devices and laptops and usually connected over a 64-bit wide memory bus, LPDDR also permits 16- or 32-bit wide channels. The "E" and "X" versions mark enhanced versions of the specifications. They formalize overclocking the memory array by usually 33%. As with standard SDRAM, most generations double the internal fetch size and external transfer speed, DDR4 and LPDDR5 being the exceptions. If the command is a NOP ( low or CA0–2 = HHH), the chip idles. If the command is a refresh command (CA0–2 = LLH), the chip enters the self-refresh state. If the command is a burst terminate (CA0–2 = HHL), the chip enters the deep power-down state. (A full reset sequence is required when leaving.) The mode registers have been greatly expanded compared to conventional SDRAM, with an 8-bit address space, and the ability to read them back. Although smaller than a serial presence detect EEPROM, enough information is included to eliminate the need for one. S2 devices smaller than 4 Gbit, and S4 devices smaller than 1 Gbit have only four banks. They ignore the BA2 signal, and do not support per-bank refresh. Non-volatile memory devices do not use the refresh commands, and reassign the precharge command to transfer address bits A20 and up. The low-order bits (A19 and down) are transferred by a following Activate command. This transfers the selected row from the memory array to one of 4 or 8 (selected by the BA bits) row data buffers, where they can be read by a Read command. Unlike DRAM, the bank address bits are not part of the memory address; any address can be transferred to any row data buffer. A row data buffer may be from 32 to 4096 bytes long, depending on the type of memory. Rows larger than 32 bytes ignore some of the low-order address bits in the Activate command. Rows smaller than 4096 bytes ignore some of the high-order address bits in the Read command. Non-volatile memory does not support the Write command to row data buffers. Rather, a series of control registers in a special address region support Read and Write commands, which can be used to erase and program the memory array. Bn = Burst address bit Cn = Column address bit Rn = Row address bit BAn = Bank address bit BGn = Bank group address bit AB = All banks (ignore BG & BA) AP = Auto-precharge MAn = Mode register address bit OPn = Operation, or mode register data WS_xx = WCK synchronization WRX = Write X; do not transfer data, but fill with all-zero or all-one WXSA, WXSB = Write X select, value to be written PD = Power down DSE = Deep sleep enable Compared to earlier standards, the nomenclature for column addresses has changed. Both LPDDR4 and LPDDR5 allow up to 10 bits of column address, but the names are different. LPDDR4's C0–C9 are renamed B0–B3 and C0–C5. As with LPDDR4, writes must start at a multiple-of-16 address with B0–B3 zero, but reads may request a burst be transferred in a different order by specifying a non-zero value for B3. As with LPDDR4, to read some data requires 4 commands: two activate commands to select a row, then a CAS and a read command to select a column. Unlike LPDDR4, the CAS command comes before the read or write command. In fact, it is something of a misnomer, in that it does not select a column at all. Instead, its primary function is to prepare the DRAM to synchronize with the imminent start of the high-speed WCK clock. The WS_FS, WS_RD and WS_WR bits select various timings, with the _RD and _WR options optimized for an immediately following read or write command, while the _FS option starts the clock immediately, and may be followed by multiple reads or writes, accessing multiple banks. CAS also specifies the "write X" option. If the WRX bit is set, writes do not transfer data, but rather fill the burst with all-zeros or all-ones, under the control of the WXS (write-X select) bit. This takes the same amount of time, but saves energy. In addition to the usual bursts of 16, there are commands for performing double-length bursts of 32. Reads (but not writes) may specify a starting position within the 32-word aligned burst using the C0 and B3 bits. Bursts of 24 transfers × 12 pins = 288 bits: 256 data bits, plus 16 tag/ECC bits stored by array, plus 16 bits for data bus inversion or link ECC, not stored. CAMM2

References

External links

Micron Samsung Elpida Nanya JEDEC pages: LOW POWER DOUBLE DATA RATE 3 SDRAM (LPDDR3)

Text derived from https://en.wikipedia.org/w/index.php?oldid=1372863094 under CC BY-SA 4.0; modifications have been made.

Sources cited in this revision

32 named source(s) extracted from the cited revision. A source with no author is shown by its publication; nothing is invented.