Mainspring
≈ 12 min read
Names in other languages
No names in other languages are held for this entry yet.
Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.
movement showing the two mainsprings which power it. This is a striking clock which sounds the hours on a chime; one of the springs powers the timekeeping gear train while the other powers the striking train. A mainspring is a spiral torsion spring of metal ribbon—commonly spring steel—used as a power source in mechanical watches, some clocks, and other clockwork mechanisms. Winding the timepiece, by turning a knob or key, stores energy in the mainspring by twisting the spiral tighter.
The force of the mainspring then turns the clock's wheels as it unwinds, until the next winding is needed. The adjectives wind-up and spring-powered refer to mechanisms powered by mainsprings, which also include kitchen timers, metronomes, music boxes, wind-up toys and clockwork radios. Mainsprings appeared in the first spring-powered clocks in 15th-century Europe. The mainspring replaced the weight hanging from a cord wrapped around a pulley, which was the power source used in all previous mechanical clock.
movement showing the two mainsprings which power it. This is a striking clock which sounds the hours on a chime; one of the springs powers the timekeeping gear train while the other powers the striking train.]] A mainspring is a spiral torsion spring of metal ribbon—commonly spring steel—used as a power source in mechanical watches, some clocks, and other clockwork mechanisms. Winding the timepiece, by turning a knob or key, stores energy in the mainspring by twisting the spiral tighter.
The force of the mainspring then turns the clock's wheels as it unwinds, until the next winding is needed. The adjectives wind-up and spring-powered refer to mechanisms powered by mainsprings, which also include kitchen timers, metronomes, music boxes, wind-up toys and clockwork radios. Mainsprings appeared in the first spring-powered clocks in 15th-century Europe. The mainspring replaced the weight hanging from a cord wrapped around a pulley, which was the power source used in all previous mechanical clock.
Hazards
The mainspring contains a lot of energy. Clocks and watches need to be serviced, cleaned and lubricated periodically, and if precautions are not taken during disassembly the spring can release suddenly, causing potentially serious injury. Before servicing, mainsprings are “let down” gently by pulling the click back while holding the winding key, allowing the spring to slowly unwind. However, even in their “let down” state, mainsprings contain dangerous residual tension. Watchmakers and clockmakers use a tool called a "mainspring winder" to safely install and remove them. Large mainsprings in clocks are immobilized by "mainspring clamps" before removal.
Stackfreed
The stackfreed was an eccentric cam mounted on the mainspring arbor, with a spring-loaded roller that pressed against it. The cam had a 'snail' shape so that early in the running period when the mainspring was pushing strongly, the spring would bear against the wide part of the cam, providing a strong opposing force, while later in the running period as the force of the mainspring decreased, the spring would bear against the narrower part of the cam and the opposing force would also decrease. The stackfreed added a lot of friction and probably reduced a clock's running time substantially; it was only used in some German timepieces and was abandoned after about a century.
Fusee
The fusee was a much longer-lasting innovation. This was a cone-shaped pulley that was turned by a chain wrapped around the mainspring barrel. Its curving shape continuously changed the mechanical advantage of the linkage to even out the force of the mainspring as it ran down. Fusees became the standard method of getting constant torque from a mainspring. They were used in most spring-driven clocks and watches from their first appearance until the 19th century when the going barrel took over, and in marine chronometers until the 1970s.
Stopwork
Another early device which helped even out the spring's force was stopwork or winding stops, which prevented the mainspring from being wound up all the way, and prevented it from unwinding all the way. The idea was to use only the central part of the spring's 'torque curve', where its force was more constant. The most common form was the Geneva stop or 'Maltese cross'. Stopwork isn't needed in modern watches.
Remontoire
A fourth device used in a few precision timepieces was the remontoire. This was a small secondary spring or weight which powered the timepiece's escapement, and was itself rewound periodically by the mainspring. This isolated the timekeeping element from the varying mainspring force.
Going barrel
The modern going barrel, invented in 1760 by Jean-Antoine Lépine, produces a constant force by simply using a longer mainspring than needed, and coiling it under tension in the barrel. In operation, only a few turns of the spring at a time are used, with the remainder pressed against the outer wall of the barrel. Mathematically, the tension creates a 'flat' section in the spring's torque curve (see graph) and only this flat section is used. In addition, the outer end of the spring is often given a reverse curve, so it has an "S" shape.
This stores more tension in the spring's outer turns where it is available toward the end of the running period. The result is that the barrel provides approximately constant torque over the watch's designed running period; the torque doesn't decline until the mainspring has almost run down. The built-in tension of the spring in the going barrel makes it hazardous to disassemble even when not wound up.
'Knocking' or 'banking'
Even if the mainsprings were not prone to breakage, too much force during winding caused another problem in early watches, called 'knocking' or 'banking'. If very little slack was left in the spring after winding ('overwinding"), the pressure of the last turn of the winding knob put the end of the spring under excessive tension, which was locked in by the last click of the ratchet. So the watch ran with excessive drive force for several hours, until the extra tension in the end of the spring was relieved.
This made the balance wheel rotate too far in each direction, causing the impulse pin on the wheel to knock against the back of the fork horns. This caused the watch to gain time, and could break the impulse pin. In older watches this was prevented with 'stopwork'. In modern watches this is prevented by designing the 'click' with some 'recoil' (backlash), to allow the arbor to rotate backward after winding by about two ratchet teeth, enough to remove excess tension.
Motor or safety barrel
Around 1900, when broken watchsprings were more of a problem, some pocketwatches used a variation of the going barrel called the motor barrel or safety barrel. Mainsprings usually broke at their attachment to the arbor, where bending stresses are greatest. When the mainspring broke, the outer part recoiled and the momentum spun the barrel in the reverse direction. This applied great force to the delicate wheel train and escapement, often breaking pivots and jewels. In the motor barrel, the functions of the arbor and barrel were reversed from the going barrel. The mainspring was wound by the barrel, and turned the arbor to drive the wheel train. Thus if the mainspring broke, the destructive recoil of the barrel would be applied not to the wheel train but to the winding mechanism, which was robust enough to take it.
Safety pinion
A safety pinion was an alternate means of protection, used with the going barrel. In this, the center wheel pinion, which the barrel gear engages, was attached to its shaft with a reverse screw thread. If the spring broke, the reverse recoil of the barrel, instead of being passed on to the gear train, would simply unscrew the pinion.
The myth of 'overwinding'
Watches and clocks are often found stopped with the mainspring fully wound, which led to a myth that winding a spring-driven timepiece all the way up damages it. Several problems can cause this type of breakdown, but it is never due to "overwinding", as timepieces are designed to handle being wound up all the way. One cause of “overwinding” is dirt. Watch movements require regular cleaning and lubrication, and the normal result of neglecting to get a watch cleaned is a watch stopped at full wind.
As the watch movement collects dirt and the oil dries up, friction increases, so that the mainspring doesn't have the force to turn the watch at the end of its normal running period, and it stops prematurely. If the owner continues to wind and use the watch without servicing, eventually the friction force reaches the 'flat' part of the torque curve, and quickly a point is reached where the mainspring doesn't have the force to run the watch even at full wind, so the watch stops with the mainspring fully wound.
The watch needs service, but the problem is caused by a dirty movement or other defect, not "overwinding". Another common cause of a watch stopped at full wind is that if a watch is dropped then the balance staff can break and the watch can no longer run even when the mainspring is fully wound.
Self-winding watches and 'unbreakable' mainsprings
Self-winding or automatic watches, introduced widely in the 1950s, use the natural motions of the wrist to keep the mainspring wound. A semicircular weight, pivoted at the center of the watch, rotates with each wrist motion. A winder mechanism uses rotations in both directions to wind the mainspring. In automatic watches, motion of the wrist could continue winding the mainspring until it broke. This is prevented with a slipping clutch device.
The outer end of the mainspring, instead of attaching to the barrel, is attached to a circular expansion spring called the bridle that presses against the inner wall of the barrel, which has serrations or notches to hold it. During normal winding the bridle holds by friction to the barrel, allowing the mainspring to wind. When the mainspring reaches its full tension, its pull is stronger than the bridle. Further rotation of the arbor causes the bridle to slip along the barrel, preventing further winding.
In watch company terminology, this is often misleadingly referred to as an 'unbreakable mainspring'.
'Tired' or 'set' mainsprings
After decades of use, mainsprings in older timepieces are found to deform slightly and lose some of their force, becoming 'tired' or 'set'. This condition is mostly found in springs in barrels. It causes the running time between windings to decrease. During servicing the mainspring should be checked for 'tiredness' and replaced if necessary. The British Horological Institute suggests these tests: In a mainspring barrel, when unwound and relaxed, most of a healthy spring's turns should be pressed flat against the wall of the barrel, with only 1 or 2 turns spiralling across the central space to attach to the arbor. If more than 2 turns are loose in the center, the spring may be 'tired'; with 4 or 5 turns it definitely is 'tired'. When removed from the barrel, if the diameter of the relaxed spring lying on a flat surface is less than 2½ times the barrel diameter, it is 'tired'.
Power reserve indicator
Some high-grade watches have an extra dial on the face indicating how much power is left in the mainspring, often graduated in hours the watch has left to run. Since both the arbor and the barrel turn, this mechanism requires a differential gear that measures how far the arbor has been turned, compared to the barrel.
Unusual forms of mainspring
A mainspring is usually a coiled metal spring, however there are exceptions: The wagon spring clock: During a brief time in American clockmaking history, coilable spring steel was not available in the United States, and inventive clockmakers built clocks powered by a stack of leaf springs, similar to what has traditionally served as a suspension spring for wagons. Other spring types are conceivable and have been used occasionally on experimental timepieces. Occasionally one finds an odd clock with a spring made of material other than metal, such as synthetic elastic materials. Federation of the Swiss Watch Industry Dictionary
Text derived from https://en.wikipedia.org/w/index.php?oldid=1377729136 under CC BY-SA 4.0; modifications have been made.