MLT-3 encoding

Uses your system voice; voice and rate in settings.

Q361607Snapshot

≈ 4 min read

Names in other languages

  • FrançaisMulti Level Transmit 3
  • EnglishMLT-3 encoding
  • 日本語MLT-3 伝送路符号
  • DeutschMLT-3-Code
  • 中文MLT-3編碼
  • eoMLT-3
  • ItalianoMLT-3
  • PolskiMLT-3

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

MLT-3 encoding (Multi-Level Transmit) is a line code (a signaling method used in a telecommunication system for transmission purposes) that uses three voltage levels. An MLT-3 interface emits less electromagnetic interference and requires less bandwidth than most other binary or ternary interfaces that operate at the same bit rate (see PCM for discussion on bandwidth / quantization tradeoffs), such as Manchester code or Alternate Mark Inversion. of a MLT-3 signal MLT-3 cycles sequentially through the voltage levels −1, 0, +1, 0. It moves to the next state to transmit a 1 bit, and stays in the same state to transmit a 0 bit. Similar to simple NRZ encoding, MLT-3 has a coding efficiency of 1 bit/baud, however it requires four transitions (baud) to complete a full cycle (from low-to-middle, middle-to-high, high-to-middle, middle-to-low). Thus, the maximum fundamental frequency is reduced to one fourth of the baud rate. This makes signal transmission more amenable to copper wires. The lack of transition on a 0 bit means that for practical use, the number of consecutive 0 bits in the transmitted data must be bounded; i.e. it must be pre-coded using a run-length limited code. This results in an effective bitrate slightly lower than one bit per baud or four bits per cycle.…

MLT-3 encoding (Multi-Level Transmit) is a line code (a signaling method used in a telecommunication system for transmission purposes) that uses three voltage levels. An MLT-3 interface emits less electromagnetic interference and requires less bandwidth than most other binary or ternary interfaces that operate at the same bit rate (see PCM for discussion on bandwidth / quantization tradeoffs), such as Manchester code or Alternate Mark Inversion. of a MLT-3 signal MLT-3 cycles sequentially through the voltage levels −1, 0, +1, 0. It moves to the next state to transmit a 1 bit, and stays in the same state to transmit a 0 bit. Similar to simple NRZ encoding, MLT-3 has a coding efficiency of 1 bit/baud, however it requires four transitions (baud) to complete a full cycle (from low-to-middle, middle-to-high, high-to-middle, middle-to-low). Thus, the maximum fundamental frequency is reduced to one fourth of the baud rate. This makes signal transmission more amenable to copper wires. The lack of transition on a 0 bit means that for practical use, the number of consecutive 0 bits in the transmitted data must be bounded; i.e. it must be pre-coded using a run-length limited code. This results in an effective bitrate slightly lower than one bit per baud or four bits per cycle. MLT-3 was first introduced by Crescendo Communications as a coding scheme for FDDI copper interconnect (TP-PMD, CDDI). Later, the same technology was used in the 100BASE-TX physical medium dependent sublayer, given the considerable similarities between FDDI and [[Fast Ethernet|100BASE-[TF]X physical media attachment layer (section 25.3 of IEEE802.3-2002 specifies that ANSI X3.263:1995 TP-PMD should be consulted, with minor exceptions). Signaling specified by 100BASE-T4 Ethernet, while it has three levels, is not compatible with MLT-3. It uses selective base-2 to base-3 conversion with direct mapping of base-3 digits to line levels (8B6T code).

Text derived from https://en.wikipedia.org/w/index.php?oldid=1360438961 under CC BY-SA 4.0; modifications have been made.

Provenance

snapshot mlt-3-encoding-041959-2ee67d67b99c5221 · hash 2ee67d67b99c5221de604a1a4bc204d71e92f69ae6d081593f980c38d23ff99b · captured 1782043840.0 · version history

Cite this page as: encyclopegia.org, “MLT-3 encoding”, snapshot mlt-3-encoding-041959-2ee67d67b99c5221. https://encyclopegia.org/a/mlt-3-encoding

Sources cited in this revision

1 named source(s) extracted from the cited revision. A source with no author is shown by its publication; nothing is invented.