{
  "id": "mosfet-024869-0210ab16e39abb16",
  "slug": "mosfet",
  "title": "MOSFET",
  "qid": "Q210793",
  "lead": "in D2PAK surface-mount packages. Operating as switches, each of these components can sustain a blocking voltage of 120 V in the off state, and can conduct a con&shy;ti&shy;nuous current of 30 A in the on state, dissipating up to about 100 W and controlling a load of over 2000 W. A matchstick is pictured for scale. In electronics, the metal–oxide–semiconductor field-effect transistor (MOSFET, MOS-FET, MOS FET, or MOS transistor) is a type of field-effect transistor (FET), most commonly fabricated by the controlled oxidation of silicon. It has an insulated gate, the voltage of which determines the conductivity of the device. This ability to change conductivity with the amount of applied voltage can be used for amplifying or switching electronic signals. The term metal–insulator–semiconductor field-effect transistor (MISFET) is almost synonymous with MOSFET. Another near-synonym is insulated-gate field-effect transistor (IGFET). Physicist Julius Edgar Lilienfeld first proposed the concept of a field-effect transistor (FET) in 1925, but it was not possible to construct a working device at that time. The first working metal–oxide–semiconductor field-effect transistor (MOSFET) was invented in 1959 by engineers Mohamed Atalla and Dawon Kahng at Bell Labs.…",
  "body": "in D2PAK surface-mount packages. Operating as switches, each of these components can sustain a blocking voltage of 120 V in the off state, and can conduct a con&shy;ti&shy;nuous current of 30&nbsp;A in the on state, dissipating up to about 100&nbsp;W and controlling a load of over 2000&nbsp;W. A matchstick is pictured for scale. In electronics, the metal–oxide–semiconductor field-effect transistor (MOSFET, MOS-FET, MOS FET, or MOS transistor) is a type of field-effect transistor (FET), most commonly fabricated by the controlled oxidation of silicon. It has an insulated gate, the voltage of which determines the conductivity of the device. This ability to change conductivity with the amount of applied voltage can be used for amplifying or switching electronic signals. The term metal–insulator–semiconductor field-effect transistor (MISFET) is almost synonymous with MOSFET. Another near-synonym is insulated-gate field-effect transistor (IGFET). Physicist Julius Edgar Lilienfeld first proposed the concept of a field-effect transistor (FET) in 1925, but it was not possible to construct a working device at that time. The first working metal–oxide–semiconductor field-effect transistor (MOSFET) was invented in 1959 by engineers Mohamed Atalla and Dawon Kahng at Bell Labs. Their breakthrough—fabricating a practical field-effect transistor enabled by Atalla’s earlier work on silicon surface passivation and thermal oxidation—revolutionized electronics and paved the way for smaller and cheaper radios, calculators, computers, and other electronic devices. The main advantage of a MOSFET is that it requires almost no input current to control the load current under steady-state or low-frequency conditions, especially compared to bipolar junction transistors (BJTs). However, at high frequencies or when switching rapidly, a MOSFET may require significant current to charge and discharge its gate capacitance. In an enhancement mode MOSFET, voltage applied to the gate terminal increases the conductivity of the device. In depletion mode transistors, voltage applied at the gate reduces the conductivity. The \"metal\" in the name MOSFET is sometimes a misnomer, because the gate material can be a layer of polysilicon (polycrystalline silicon). Similarly, \"oxide\" in the name can also be a misnomer, as different dielectric materials are used with the aim of obtaining strong channels with smaller applied voltages. The MOSFET is by far the most common transistor in digital circuits, as billions may be included in a memory chip or microprocessor. As MOSFETs can be made with either a p-type or n-type channel, complementary pairs of MOS transistors can be used to make switching circuits with very low power consumption, in the form of CMOS logic. When a voltage is applied across a MOS structure, it modifies the distribution of charges in the semiconductor. If we consider a p-type semiconductor (with N A the density of acceptors, p the density of holes; p = N A in neutral bulk), a positive voltage, V G , from gate to body (see figure) creates a depletion layer by forcing the positively charged holes away from the gate-insulator/semiconductor interface, leaving exposed a carrier-free region of immobile, negatively charged acceptor ions (see doping). If V G is high enough, a high concentration of negative charge carriers forms in an inversion layer located in a thin layer next to the interface between the semiconductor and the insulator. Conventionally, the gate voltage at which the volume density of electrons in the inversion layer is the same as the volume density of holes in the body is called the threshold voltage. When the voltage between transistor gate and source (V G ) exceeds the threshold voltage (V th ), the difference is known as overdrive voltage. This structure with p-type body is the basis of the n-type MOSFET, which requires the addition of n-type source and drain regions. ==== Cutoff, subthreshold, and weak-inversion mode==== Criterion: V_\\text{GS} According to the basic threshold model, the transistor is turned off, and there is no conduction between drain and source. A more accurate model considers the effect of thermal energy on the Fermi–Dirac distribution of electron energies which allow some of the more energetic electrons at the source to enter the channel and flow to the drain. This results in a subthreshold current that is an exponential function of gate-source voltage. While the current between drain and source should ideally be zero when the transistor is being used as a turned-off switch, there is a weak-inversion current, sometimes called subthreshold leakage. In weak inversion where the source is tied to bulk, the current varies exponentially with V_\\text{GS} as given approximately by: I_\\text{D} \\approx I_\\text{D0} e^\\frac{V_\\text{GS} - V_\\text{th}}{nV_\\text{T}}, where: I_\\text{D0} is the current when V_\\text{GS} {=} V_\\text{th} , V_\\text{T} {=} kT/q is the thermal voltage, and n is the slope factor given by: n = 1 + \\frac{C_\\text{dep}}{C_\\text{ox}}, where C_\\text{dep} is the capacitance of the depletion layer and C_\\text{ox} is the capacitance of the oxide layer. This equation is generally used, but is only an adequate approximation for the source tied to the bulk. For the source not tied to the bulk, the subthreshold equation for drain current in saturation is I_\\text{D} \\approx I_\\text{D0} e^\\frac{V_\\text{G} - V_\\text{th}}{nV_\\text{T}} e^{-\\frac{ V_\\text{S}}{V_\\text{T}}}. In a long-channel device, there is no drain voltage dependence of the current once V_\\text{DS} \\gg V_\\text{T} , but as channel length is reduced drain-induced barrier lowering introduces drain voltage dependence that depends in a complex way upon the device geometry (for example, the channel doping, the junction doping and so on). Frequently, threshold voltage V th for this mode is defined as the gate voltage at which a selected value of current I D0 occurs, for example, I D0 = 1 μA, which may not be the same V th -value used in the equations for the following modes. Some micropower analog circuits are designed to take advantage of subthreshold conduction. By working in the weak-inversion region, the MOSFETs in these circuits deliver the highest possible transconductance-to-current ratio, namely: g_m/I_\\text{D} = 1/\\left(nV_\\text{T}\\right) , almost that of a bipolar transistor. The subthreshold I–V curve depends exponentially upon threshold voltage, introducing a strong dependence on any manufacturing variation that affects threshold voltage; for example: variations in oxide thickness, junction depth, or body doping that change the degree of drain-induced barrier lowering. The resulting sensitivity to fabricational variations complicates optimization for leakage and performance. near drain. I_\\text{D} = \\mu_n C_\\text{ox}\\frac{W}{L} \\left( \\left(V_\\text{GS} - V_{\\rm th}\\right)V_\\text{DS} - \\frac{{V_\\text{DS}}^2}{2} \\right) , where \\mu_n is the charge-carrier effective mobility, W is the gate width, L is the gate length and C_\\text{ox} is the gate oxide capacitance per unit area. The transition from the exponential subthreshold region to the triode region is not as sharp as the equations suggest. ====Saturation or active mode==== Criteria: V_\\text{GS} > V_\\text{th} and V_\\text{DS} \\geq (V_\\text{GS} - V_\\text{th}) . The switch is turned on, and a channel has been created, which allows current between the drain and source. Since the drain voltage is higher than the source voltage, the electrons spread out, and conduction is not through a narrow channel but through a broader, two- or three-dimensional current distribution extending away from the interface and deeper in the substrate. The onset of this region is also known as pinch-off to indicate the lack of channel region near the drain. Although the channel does not extend the full length of the device, the electric field between the drain and the channel is very high, and conduction continues. The drain current is now weakly dependent upon drain voltage and controlled primarily by the gate-source voltage, and modeled approximately as: I_\\text{D} = \\frac{\\mu_n C_\\text{ox}}{2}\\frac{W}{L}\\left[V_\\text{GS} - V_\\text{th}\\right]^2 \\left[1 + \\lambda V_\\text{DS}\\right]. The additional factor involving λ, the channel-length modulation parameter, models current dependence on drain voltage due to the Early effect, or channel length modulation. According to this equation, a key design parameter, the MOSFET transconductance is: g_m = \\frac{\\partial I_D}{\\partial V_\\text{GS}} = \\frac{2I_\\text{D}}{V_\\text{GS} - V_\\text{th}} = \\frac{2I_\\text{D}}{V_\\text{ov}} , where the combination V ov = V GS &nbsp;− V th is called the overdrive voltage, and where V DSsat = V GS &nbsp;− V th accounts for a small discontinuity in I_\\text{D} which would otherwise appear at the transition between the triode and saturation regions. Another key design parameter is the MOSFET output resistance r out given by: r_\\text{out} = \\frac{1}{\\lambda I_\\text{D}} \\, . Note: r out is the inverse of g DS , where g_\\text{DS} = \\frac{\\partial I_\\text{DS}}{\\partial V_\\text{DS}} . I D is the expression in the saturation region. If λ is taken as zero, an infinite output resistance of the device results that leads to unrealistic circuit predictions, particularly in analog circuits. As the channel length becomes very short, these equations become quite inaccurate. New physical effects arise. For example, carrier transport in the active mode may become limited by velocity saturation. When velocity saturation dominates, the saturation drain current is more nearly linear than quadratic in V GS . At even shorter lengths, carriers transport with near zero scattering, known as quasi-ballistic transport. In the ballistic regime, the carriers travel at an injection velocity that may exceed the saturation velocity and approaches the Fermi velocity at high inversion charge density. In addition, drain-induced barrier lowering increases off-state (cutoff) current and requires an increase in threshold voltage to compensate, which in turn reduces the saturation current. V_\\text{TB} = V_{T0} + \\gamma \\left( \\sqrt{V_\\text{SB} + 2\\varphi_B} - \\sqrt{2\\varphi_B} \\right), where V TB is the threshold voltage with substrate bias present, and V T0 is the zero-V SB value of threshold voltage, \\gamma is the body effect parameter, and 2φ B is the approximate potential drop between surface and bulk across the depletion layer when and gate bias is sufficient to ensure that a channel is present. As this equation shows, a reverse bias causes an increase in threshold voltage V TB and therefore demands a larger gate voltage before the channel populates. The body can be operated as a second gate, and is sometimes referred to as the \"back gate\"; the body effect is sometimes called the \"back-gate effect\". Q = \\kappa \\epsilon_0 E, with Q = charge density, κ = dielectric constant, ε 0 = permittivity of empty space and E = electric field. From this law it appears the same charge can be maintained in the channel at a lower field provided κ is increased. The voltage on the gate is given by: V_\\text{G} = V_\\text{ch} + E\\, t_\\text{ins} = V_\\text{ch} + \\frac{Q t_\\text{ins}}{\\kappa \\epsilon_0}, with V G = gate voltage, V ch = voltage at channel side of insulator, and t ins = insulator thickness. This equation shows the gate voltage will not increase when the insulator thickness increases, provided κ increases to keep t ins / κ = constant (see the article on high-κ dielectrics for more detail, and the section in this article on gate-oxide leakage). The insulator in a MOSFET is a dielectric which can in any event be silicon oxide, formed by LOCOS but many other dielectric materials are employed. The generic term for the dielectric is gate dielectric since the dielectric lies directly below the gate electrode and above the channel of the MOSFET. ===Higher subthreshold conduction=== As MOSFET geometries shrink, the voltage that can be applied to the gate must be reduced to maintain reliability. To maintain performance, the threshold voltage of the MOSFET has to be reduced as well. As threshold voltage is reduced, the transistor cannot be switched from complete turn-off to complete turn-on with the limited voltage swing available; the circuit design is a compromise between strong current in the on case and low current in the off case, and the application determines whether to favor one over the other. Subthreshold leakage (including subthreshold conduction, gate-oxide leakage and reverse-biased junction leakage), which was ignored in the past, now can consume upwards of half of the total power consumption of modern high-performance VLSI chips. ===Increased gate-oxide leakage=== The gate oxide, which serves as insulator between the gate and channel, should be made as thin as possible to increase the channel conductivity and performance when the transistor is on and to reduce subthreshold leakage when the transistor is off. However, with current gate oxides with a thickness of around 1.2&nbsp;nm (which in silicon is ~5&nbsp;atoms thick) the quantum mechanical phenomenon of electron tunneling occurs between the gate and channel, leading to increased power consumption. Silicon dioxide has traditionally been used as the gate insulator. Silicon dioxide however has a modest dielectric constant. Increasing the dielectric constant of the gate dielectric allows a thicker layer while maintaining a high capacitance (capacitance is proportional to dielectric constant and inversely proportional to dielectric thickness). All else equal, a higher dielectric thickness reduces the quantum tunneling current through the dielectric between the gate and the channel. Insulators that have a larger dielectric constant than silicon dioxide (referred to as high-κ dielectrics), such as group IVb metal silicates e.g. hafnium and zirconium silicates and oxides are being used to reduce the gate leakage from the 45 nanometer technology node onwards. On the other hand, the barrier height of the new gate insulator is an important consideration; the difference in conduction band energy between the semiconductor and the dielectric (and the corresponding difference in valence band energy) also affects leakage current level. For the traditional gate oxide, silicon dioxide, the former barrier is approximately 8 eV. For many alternative dielectrics the value is significantly lower, tending to increase the tunneling current, somewhat negating the advantage of higher dielectric constant. The maximum gate-source voltage is determined by the strength of the electric field able to be sustained by the gate dielectric before significant leakage occurs. As the insulating dielectric is made thinner, the electric field strength within it goes up for a fixed voltage. This necessitates using lower voltages with the thinner dielectric. ===Increased junction leakage=== To make devices smaller, junction design has become more complex, leading to higher doping levels, shallower junctions, \"halo\" doping and so forth, all to decrease drain-induced barrier lowering (see the section on junction design). To keep these complex junctions in place, the annealing steps formerly used to remove damage and electrically active defects must be curtailed increasing junction leakage. Heavier doping is also associated with thinner depletion layers and more recombination centers that result in increased leakage current, even without lattice damage. ===Drain-induced barrier lowering and V T roll off=== Drain-induced barrier lowering (DIBL) and V T roll off: Because of the short-channel effect, channel formation is not entirely done by the gate, but now the drain and source also affect the channel formation. As the channel length decreases, the depletion regions of the source and drain come closer together and make the threshold voltage (V T ) a function of the length of the channel. This is called V T roll-off. V T also becomes function of drain to source voltage V DS . As we increase the V DS , the depletion regions increase in size, and a considerable amount of charge is depleted by the V DS . The gate voltage required to form the channel is then lowered, and thus, the V T decreases with an increase in V DS . This effect is called drain induced barrier lowering (DIBL). ===Lower output resistance=== For analog operation, good gain requires a high MOSFET output impedance, which is to say, the MOSFET current should vary only slightly with the applied drain-to-source voltage. As devices are made smaller, the influence of the drain competes more successfully with that of the gate due to the growing proximity of these two electrodes, increasing the sensitivity of the MOSFET current to the drain voltage. To counteract the resulting decrease in output resistance, circuits are made more complex, either by requiring more devices, for example the cascode and cascade amplifiers, or by feedback circuitry using operational amplifiers, for example a circuit like that in the adjacent figure. ===Lower transconductance=== The transconductance of the MOSFET decides its gain and is proportional to hole or electron mobility (depending on device type), at least for low drain voltages. As MOSFET size is reduced, the fields in the channel increase and the dopant impurity levels increase. Both changes reduce the carrier mobility, and hence the transconductance. As channel lengths are reduced without proportional reduction in drain voltage, raising the electric field in the channel, the result is velocity saturation of the carriers, limiting the current and the transconductance. ===Interconnect capacitance=== Traditionally, switching time was roughly proportional to the gate capacitance of gates. However, with transistors becoming smaller and more transistors being placed on the chip, interconnect capacitance (the capacitance of the metal-layer connections between different parts of the chip) is becoming a large percentage of capacitance. Signals have to travel through the interconnect, which leads to increased delay and lower performance. ===Heat production=== The ever-increasing density of MOSFETs on an integrated circuit creates problems of substantial localized heat generation that can impair circuit operation. Circuits operate more slowly at high temperatures, and have reduced reliability and shorter lifetimes. Heat sinks and other cooling devices and methods are now required for many integrated circuits including microprocessors. Power MOSFETs are at risk of thermal runaway. As their on-state resistance rises with temperature, if the load is approximately a constant-current load then the power loss rises correspondingly, generating further heat. When the heatsink is not able to keep the temperature low enough, the junction temperature may rise quickly and uncontrollably, resulting in destruction of the device. ===Process variations=== With MOSFETs becoming smaller, the number of atoms in the silicon that produce many of the transistor's properties is becoming fewer, with the result that control of dopant numbers and placement is more erratic. During chip manufacturing, random process variations affect all transistor dimensions: length, width, junction depths, oxide thickness etc., and become a greater percentage of overall transistor size as the transistor shrinks. The transistor characteristics become less certain, more statistical. The random nature of manufacture means we do not know which particular example MOSFETs actually will end up in a particular instance of the circuit. This uncertainty forces a less optimal design because the design must work for a great variety of possible component MOSFETs. See process variation, design for manufacturability, reliability engineering, and statistical process control. ===Modeling challenges=== Modern ICs are computer-simulated with the goal of obtaining working circuits from the first manufactured lot. As devices are miniaturized, the complexity of the processing makes it difficult to predict exactly what the final devices look like, and modeling of physical processes becomes more challenging as well. In addition, microscopic variations in structure due simply to the probabilistic nature of atomic processes require statistical (not just deterministic) predictions. These factors combine to make adequate simulation and \"right the first time\" manufacture difficult.",
  "categories": [
    "107141658",
    "130110808",
    "21493616",
    "22897025",
    "22903720",
    "22905761",
    "22906839",
    "22913208",
    "22915575",
    "22921555",
    "23015565",
    "23022801",
    "23187081",
    "23295778",
    "23603337",
    "24043274",
    "24745113",
    "24745121",
    "24745122",
    "24745126",
    "26220375",
    "28269686",
    "37160764",
    "37645845",
    "53798929",
    "61223478",
    "69725831",
    "84370014",
    "89061531"
  ],
  "license": "CC BY-SA 4.0",
  "source_uri": "https://en.wikipedia.org/w/index.php?oldid=1375789342",
  "content_hash": "0210ab16e39abb166733dcbb5996df77c8cf8a01c1c3682be2f9d13bfd4dcdd6",
  "created_at": 1792308513.3166883,
  "updated_at": 1789863343.0,
  "claims": [],
  "contradictions": [],
  "confidence": 0.6,
  "csl": {
    "id": "mosfet-024869-0210ab16e39abb16",
    "type": "webpage",
    "title": "MOSFET",
    "author": [
      {
        "family": "Anticloud FZ LLE",
        "literal": "Anticloud FZ LLE"
      }
    ],
    "container-title": "encyclopegia.org",
    "publisher": "Anticloud FZ LLE",
    "publisher-place": "Dubai, United Arab Emirates",
    "URL": "https://encyclopegia.org/a/mosfet",
    "issued": {
      "date-parts": [
        [
          2026,
          10,
          18
        ]
      ]
    },
    "accessed": {
      "date-parts": [
        [
          2026,
          11,
          21
        ]
      ]
    },
    "license": "CC BY-SA 4.0",
    "DOI": "eo1:mosfet-024869-0210ab16e39abb16",
    "isBasedOn": "https://en.wikipedia.org/w/index.php?oldid=1375789342",
    "note": "Immutable snapshot mosfet-024869-0210ab16e39abb16, content root 0210ab16e39abb16…"
  }
}