Multimeter
A multimeter (also known as a multi-tester, volt-ohm-milliammeter, volt-ohmmeter or VOM, avometer or ampere-volt-ohmmeter) is a measuring instrument that can measure multiple electrical properties.
≈ 4 min read
Names in other languages
No names in other languages are held for this entry yet.
Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.
A multimeter (also known as a multi-tester, volt-ohm-milliammeter, volt-ohmmeter or VOM, avometer or ampere-volt-ohmmeter) is a measuring instrument that can measure multiple electrical properties. A typical multimeter can measure voltage, resistance, and current, in which case can be used as a voltmeter, ohmmeter, and ammeter.
Some feature the measurement of additional properties such as temperature and capacitance. Analog multimeters use a microammeter with a moving pointer to display readings. Digital multimeters (DMMs) have numeric displays and are more precise than analog multimeters as a result.
Meters will typically include probes that temporarily connect the instrument to the device or circuit under test, and offer some intrinsic safety features to protect the operator if the instrument is connected to high voltages that exceed its measurement capabilities. Multimeters vary in size, features, and price. They can be portable handheld devices or highly-precise bench instruments.
Multimeters are used in diagnostic operations to verify the correct operation of a circuit or to test passive components for values in tolerance with their specifications. When used for measuring voltage, the input impedance of the multimeter must be very high compared to the impedance of the circuit being measured; otherwise circuit operation may be affected and the reading will be inaccurate.
Meters with electronic amplifiers (all digital multimeters and some analog meters) have a fixed input impedance that is high enough not to disturb most circuits. This is often either one or ten megohms; the standardization of the input resistance allows the use of external high-resistance probes which form a voltage divider with the input resistance to extend voltage range up to tens of thousands of volts.
High-end multimeters generally provide an input impedance greater than 10 GΩ for ranges less than or equal to 10 V. Some high-end multimeters provide >10 Gigaohms of impedance to ranges greater than 10 V. Most analog multimeters of the moving-pointer type are unbuffered, and draw current from the circuit under test to deflect the meter pointer. The impedance of the meter varies depending on the basic sensitivity of the meter movement and the range which is selected.
For example, a meter with a typical 20,000 Ω/V sensitivity will have an input resistance of 2 MΩ on the 100 V range (100 V × 20,000 Ω/V = 2,000,000 Ω). On every range, at full-scale voltage of the range, the full current required to deflect the meter movement is taken from the circuit under test.
Lower sensitivity meter movements are acceptable for testing in circuits where source impedances are low compared to the meter impedance, for example, power circuits; these meters are more rugged mechanically. Some measurements in signal circuits require higher sensitivity movements so as not to load the circuit under test with the meter impedance.
Sensitivity should not be confused with resolution of a meter, which is defined as the lowest signal change (voltage, current, resistance and so on) that can change the observed reading. For general-purpose digital multimeters, the lowest voltage range is typically several hundred millivolts AC or DC, but the lowest current range may be several hundred microamperes, although instruments with greater current sensitivity are available.
Multimeters designed for (mains) "electrical" use instead of general electronics engineering use will typically forego the microamps current ranges. Measurement of low resistance requires lead resistance (measured by touching the test probes together) to be subtracted for best accuracy. This can be done with the "delta", "zero", or "null" feature of many digital multimeters.
Contact pressure to the device under test and cleanliness of the surfaces can affect measurements of very low resistances. Some meters offer a four wire test where two probes supply the source voltage and the others take measurement.
Using a very high impedance allows for very low voltage drop in the probes and resistance of the source probes is ignored resulting in very accurate results. The upper end of multimeter measurement ranges varies considerably; measurements over perhaps 600 volts, 10 amperes, or 100 megohms may require a specialized test instrument.
Text derived from https://en.wikipedia.org/w/index.php?oldid=1374401500 under CC BY-SA 4.0; modifications have been made.