Network switch

Uses your system voice; voice and rate in settings.

Snapshot

≈ 4 min read

Names in other languages

No names in other languages are held for this entry yet.

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

ERS 2550T-PWR, a 50-port Ethernet switch A network switch (also called switching hub, bridging hub, Ethernet switch, and—by the IEEE—MAC bridge ) is networking hardware that connects devices on a computer network by using packet switching to receive and forward data to the destination device. A network switch is a multiport network bridge that uses MAC addresses to forward data at the data link layer (layer 2) of the OSI model. Some switches can also forward data at the network layer (layer 3) by additionally incorporating routing functionality. Such switches are commonly known as layer-3 switches or multilayer switches. Switches for Ethernet are the most common form of network switch. The first MAC Bridge was invented in 1983 by Mark Kempf, an engineer in the Networking Advanced Development group of Digital Equipment Corporation (DEC). The first two-port bridge product (LANBridge 100) was introduced by that company shortly after. The company subsequently produced multi-port switches for both Ethernet and FDDI. DEC decided to license its MAC Bridge patent on a royalty-free, non-discriminatory basis that allowed IEEE standardization. This permitted a number of other companies to produce multi-port switches, including Kalpana.…

ERS 2550T-PWR, a 50-port Ethernet switch A network switch (also called switching hub, bridging hub, Ethernet switch, and—by the IEEE—MAC bridge ) is networking hardware that connects devices on a computer network by using packet switching to receive and forward data to the destination device. A network switch is a multiport network bridge that uses MAC addresses to forward data at the data link layer (layer 2) of the OSI model. Some switches can also forward data at the network layer (layer 3) by additionally incorporating routing functionality. Such switches are commonly known as layer-3 switches or multilayer switches. Switches for Ethernet are the most common form of network switch. The first MAC Bridge was invented in 1983 by Mark Kempf, an engineer in the Networking Advanced Development group of Digital Equipment Corporation (DEC). The first two-port bridge product (LANBridge 100) was introduced by that company shortly after. The company subsequently produced multi-port switches for both Ethernet and FDDI. DEC decided to license its MAC Bridge patent on a royalty-free, non-discriminatory basis that allowed IEEE standardization. This permitted a number of other companies to produce multi-port switches, including Kalpana. Ethernet was initially a shared-access medium, but the introduction of the MAC bridge began its transformation into its most-common point-to-point form without a collision domain. Switches also exist for other types of networks, including Fibre Channel, Asynchronous Transfer Mode, and InfiniBand. Unlike repeater hubs, which broadcast the same data out of each port and let the devices pick out the data addressed to them, a network switch learns the Ethernet addresses of connected devices and then only forwards data to the port connected to the device to which it is addressed.

Traffic monitoring

It is difficult to monitor traffic that is bridged using a switch because only the sending and receiving ports can see the traffic. Methods that are specifically designed to allow a network analyst to monitor traffic include: Port mirroring Because the purpose of a switch is to not forward traffic to network segments where it would be superfluous, a node attached to a switch cannot monitor traffic on other segments. Port mirroring is how this problem is addressed in switched networks: In addition to the usual behavior of forwarding frames only to ports through which they might reach their addressees, the switch forwards frames received through a given monitored port to a designated monitoring port, allowing analysis of traffic that would otherwise not be visible through the switch. Switch monitoring (SMON) is described by RFC 2613 and is a provision for controlling facilities such as port mirroring. RMON sFlow These monitoring features are rarely present on consumer-grade switches. Other monitoring methods include connecting a layer-1 hub or network tap between the monitored device and its switch port.

Text derived from https://en.wikipedia.org/w/index.php?oldid=1374670195 under CC BY-SA 4.0; modifications have been made.

Sources cited in this revision

23 named source(s) extracted from the cited revision. A source with no author is shown by its publication; nothing is invented.