noise figure

device in communications engineering

Uses your system voice; voice and rate in settings.

Q746825Snapshot

≈ 9 min read

Names in other languages

  • cafactor de soroll
  • Françaisfacteur de bruit
  • EspañolFactor de ruido
  • Italianocifra di rumore
  • Englishnoise figure
  • DeutschRauschzahl
  • עבריתספרת רחש
  • 日本語雑音指数

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

Noise figure (NF) and noise factor (F) are figures of merit that indicate degradation of the signal-to-noise ratio (SNR) that is caused by components in a signal chain. These figures of merit are used to evaluate the performance of an amplifier or a radio receiver, with lower values indicating better performance.

The noise factor is defined as the unitless ratio of the output noise power of a device to the portion thereof attributable to thermal noise in the input termination at standard noise temperature T 0 (usually 290 K). The noise factor is thus the ratio of actual output noise to that which would remain if the device itself did not introduce noise, which is equivalent to the ratio of input SNR to output SNR. The noise figure is the power level of the noise factor, calculated in terms of the logarithm of noise factor and expressed in scale of decibels (dB).

Noise figure (NF) and noise factor (F) are figures of merit that indicate degradation of the signal-to-noise ratio (SNR) that is caused by components in a signal chain. These figures of merit are used to evaluate the performance of an amplifier or a radio receiver, with lower values indicating better performance.

The noise factor is defined as the unitless ratio of the output noise power of a device to the portion thereof attributable to thermal noise in the input termination at standard noise temperature T 0 (usually 290 K). The noise factor is thus the ratio of actual output noise to that which would remain if the device itself did not introduce noise, which is equivalent to the ratio of input SNR to output SNR. The noise figure is the power level of the noise factor, calculated in terms of the logarithm of noise factor and expressed in scale of decibels (dB). |indent = |title= |equation = F = \frac{\mathrm{SNR}_\text{i}}{\mathrm{SNR}_\text{o}} |cellpadding= 6 |border |border colour = #0073CF |background colour=#F5FFFA}} where and are the input and output signal-to-noise ratios respectively.

The quantities are unitless power ratios. Note that this specific definition is only valid for an input signal of which the noise is N i =kT 0 B. The noise figure is defined as the noise factor in units of decibels (dB): {{Equation box 1 |indent = |title= |equation = \mathrm{NF} = 10 \log_{10}(F) = 10 \log_{10}\left(\frac{\mathrm{SNR}_\text{i}}{\mathrm{SNR}_\text{o}}\right) = \mathrm{SNR}_\text{i, dB} - \mathrm{SNR}_\text{o, dB} |cellpadding= 6 |border |border colour = #0073CF |background colour=#F5FFFA}} where and are in units of (dB).

These formulae are only valid when the input termination is at standard noise temperature , although in practice small differences in temperature do not significantly affect the values. The noise factor of a device is related to its noise temperature : F = 1 + \frac{T_\text{e}}{T_0}. Attenuators have a noise factor equal to their attenuation ratio when their physical temperature equals .

More generally, for an attenuator at a physical temperature , the noise temperature is , giving a noise factor F = 1 + \frac{(L - 1)T}{T_0}. F = F_1 + \frac{F_2 - 1}{G_1} + \frac{F_3 - 1}{G_1 G_2} + \frac{F_4 - 1}{G_1 G_2 G_3} + \cdots + \frac{F_n - 1}{G_1 G_2 G_3 \cdots G_{n-1}}, where is the noise factor for the -th device, and is the power gain (linear, not in dB) of the -th device.

The first amplifier in a chain usually has the most significant effect on the total noise figure because the noise figures of the following stages are reduced by stage gains. Consequently, the first amplifier usually has a low noise figure, and the noise figure requirements of subsequent stages is usually more relaxed.

Noise factor as a function of additional noise

The noise factor may be expressed as a function of the additional output referred noise power N_a and the power gain G of an amplifier.

Derivation

From the definition of noise factor F = \frac{\mathrm{SNR}_\text{i}}{\mathrm{SNR}_\text{o}}=\frac{\frac{S_i}{N_i}}{\frac{S_o}{N_o}}, and assuming a system which has a noisy single stage amplifier. The signal to noise ratio of this amplifier would include its own output referred noise N_a , the amplified signal S_iG and the amplified input noise N_iG , \frac{S_o}{N_o}=\frac{S_iG}{N_a+N_iG} Substituting the output SNR to the noise factor definition, F = \frac{\frac{S_i}{N_i}}{\frac{S_iG}{N_a+N_iG}}=\frac{N_a+N_iG}{N_iG} = 1 + \frac{N_a}{N_iG} In cascaded systems N_i does not refer to the output noise of the previous component.

An input termination at the standard noise temperature is still assumed for the individual component. This means that the additional noise power added by each component is independent of the other components.

Optical noise figure

The above describes noise in electrical systems. The optical noise figure is discussed in multiple sources. Electric sources generate noise with a power spectral density, or energy per mode, equal to , where is the Boltzmann constant and is the absolute temperature.

One mode has two quadratures, i.e. the amplitudes of \mathrm{\omega}t and \mathrm{\omega}t oscillations of voltages, currents or fields. However, there is also noise in optical systems. In these, the sources have no fundamental noise.

Instead the energy quantization causes notable shot noise in the detector. In an optical receiver which can output one available mode or two available quadratures this corresponds to a noise power spectral density, or energy per mode, of where is the Planck constant and is the optical frequency.

In an optical receiver with only one available quadrature the shot noise has a power spectral density, or energy per mode, of only . In the 1990s, an optical noise figure has been defined. This has been called for photon number fluctuations.

The powers needed for SNR and noise factor calculation are the electrical powers caused by the current in a photodiode. SNR is the square of mean photocurrent divided by variance of photocurrent. Monochromatic or sufficiently attenuated light has a Poisson distribution of detected photons.

If, during a detection interval the expectation value of detected photons is then the variance is also and one obtains = = . Behind an optical amplifier with power gain there will be a mean of detectable signal photons. In the limit of large the variance of photons is where is the spontaneous emission factor.

One obtains = = . Resulting optical noise factor is = = . is in conceptual conflict with the electrical noise factor, which is now called : Photocurrent is proportional to optical power . is proportional to squares of a field amplitude (electric or magnetic). So, the receiver is nonlinear in amplitude.

The "Power" needed for calculation is proportional to the 4th power of the signal amplitude. But for in the electrical domain the power is proportional to the square of the signal amplitude. If is a noise factor then its definition must be independent of measurement apparatus and frequency.

Consider the signal "Power" in the sense of definition. Behind an amplifier it is proportional to . We may replace the photodiode by a thermal power meter, and measured photocurrent by measured temperature change \mathrm{\Delta\theta} .

"Power", being proportional to or , is also proportional to (\mathrm{\Delta\theta}) . Thermal power meters can be built at all frequencies. Hence it is possible to lower the frequency from optical (say 200 THz) to electrical (say 200 MHz).

Still there, "Power" must be proportional to (\mathrm{\Delta\theta}) or . Electrical power is proportional to the square of voltage . But "Power" is proportional to .

These implications are in obvious conflict with ~150 years of physics. They are compelling consequence of calling a noise factor, or noise figure when expressed in dB. At any given electrical frequency, noise occurs in both quadratures, i.e. in phase (I) and in quadrature (Q) with the signal.

Both these quadratures are available behind the electrical amplifier. The same holds in an optical amplifier. But the direct detection photoreceiver needed for measurement of takes mainly the in-phase noise into account whereas quadrature noise can be neglected for high .

Also, the receiver outputs only one baseband signal, corresponding to quadrature. So, one quadrature or degree-of-freedom is lost. For an optical amplifier with large it holds ≥ 2 whereas for an electrical amplifier it holds ≥ 1.

Moreover, today's long-haul optical fiber communication is dominated by coherent optical I&Q receivers but does not describe the SNR degradation observed in these. Another optical noise figure for amplified spontaneous emission has been defined. But the noise factor is not the SNR degradation factor in any optical receiver.

All the above conflicts are resolved by the optical in-phase and quadrature noise factor and figure . It can be measured using a coherent optical I&Q receiver. In these, power of the output signal is proportional to the square of an optical field amplitude because they are linear in amplitude.

They pass both quadratures. For an optical amplifier it holds = ≥ 1. Quantity is the input-referred number of added noise photons per mode. and can easily be converted into each other.

For large it holds = or, when expressed in dB, is 3 dB less than . The ideal in dB equals 0 dB. This describes the known fact that the sensitivity of an ideal optical I&Q receiver is not improved by an ideal optical preamplifier.

References

.

Noise Figure Calculator 2- to 30-Stage Cascade Noise Figure and Y Factor Method Basics and Tutorial Mobile phone noise figure

Text derived from https://en.wikipedia.org/w/index.php?oldid=1336033637 under CC BY-SA 4.0; modifications have been made.

Sources cited in this revision

No external citation was extracted for this revision. That is a statement about the source, not a claim that none exists.