Overburden pressure
Pressure is force magnitude applied over an area.
≈ 5 min read
Names in other languages
No names in other languages are held for this entry yet.
Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.
Pressure is force magnitude applied over an area. Overburden pressure is a geology term that denotes the pressure caused by the weight of the overlying layers of material at a specific depth under the earth's surface. Overburden pressure is also called lithostatic pressure, or vertical stress.
This pressure is usually indicated as \sigma_v , or alternatively \sigma_z , in the coordinate system of the stress ellipsoid. At any depth in the subsurface, a point subjected to stresses can be analysed by resolving these stresses along three mutually perpendicular axes, constructing the stress ellipsoid whose axes correspond respectively to the directions of maximum, minimum and intermediate stress.
In tectonically stable regions, or under an extensional tectonic regime, the major axis of this ellipsoid is oriented vertically and corresponds in direction and magnitude to lithostatic pressure. P(z) = P_0 + g \int_{0}^{z} \rho(z) \, dz where: z is the depth in meters.
P(z) is the overburden pressure at depth z . P_0 is the pressure at the surface. \rho(z) is the density of the material above the depth z . g is the gravity acceleration in m/s^2 . In deep-earth geophysics/geodynamics, gravitational acceleration varies significantly over depth and g should not be assumed to be constant, and should be inside the integral.
The unit of measurement commonly used in geology is the bar or kilobar. One bar equals 10^5 Pa ≈ 0.9869 atmospheres. For quick calculations, the lithostatic pressure (P_l) at a given depth can be estimated using the simplified equation: P_l = ρgZ where ρ = average density of the rocks forming the overlying rock column; g = acceleration due to gravity; Z = height of the column.
Some sections of stratigraphic layers can be sealed or isolated. These changes create areas where there is not static equilibrium. A location in the layer is said to be in under pressure when the local pressure is less than the hydrostatic pressure, and in overpressure when the local pressure is greater than the hydrostatic pressure.
Numerous measurements of vertical stresses carried out in mines, tunnels and other conditions related to geomining activities, subsurface engineering or underground scientific research have confirmed the general validity of the above equation regarding the variation of pressure along the vertical, with some exceptions mainly in surveys conducted at shallow depths. By contrast, it is not easy to experimentally determine and estimate the value of horizontal stresses at a depth z. For convenience and simplicity of analysis this problem is addressed by considering the ratio k between the average of the horizontal stresses and the vertical stress, using the following equation: \frac{(\sigma_H + \sigma_h)}{2} = \bar{\sigma}_H = K\sigma_v = Kp(z) and therefore K = \frac{\bar{\sigma}_H}{\sigma_v} where \sigma_H and \sigma_h are respectively the maximum and minimum horizontal stresses, \bar{\sigma}_H is the average horizontal stress, and K is called the lateral stress coefficient.
In 1952 Terzaghi , evaluating the conditions of the rock mass as a load-bearing body whose lateral expansion (deformation) is prevented during vertical loading, suggested that the value of the parameter k was independent of depth but a function of the Poisson's ratio, specific to the rock present at depth z, according to the equation: k = \frac{\nu}{1-\nu} In consolidated rocks the values of Poisson's ratio generally vary between 0.2 and 0.3, consequently k would vary between 0.25 and 0.43. This equation treats the behaviour of the rock mass as comparable to that of an elastic material and does not consider the contribution of tectonic stresses to horizontal pressure values.
Although it is widely used for a first rough estimate of the stress ellipsoid (assuming equality of stresses along the x and y axes), decades of measurements indicate that it is not always accurate. Measured values of k are often higher than theoretical values at shallow depths and decrease with increasing depth, within the following range: 100/z + 0.3 k k = 1 is still commonly accepted and used in some branches of the Earth sciences that do not require the use of the stress ellipsoid, such as petrology.
By contrast, in disciplines requiring quantitative and directional evaluation of stresses within the Earth—such as civil engineering, mining engineering, structural geology analysis and geomechanics—it is no longer considered adequate except as a simple reference model. Geomechanics researchers have suggested that such anisotropies may exist for at least 50 km within the Earth's crust, with values of around 20,000 psi.
See also
Effective stress Geothermobarometry Lateral earth pressure Pore water pressure Sedimentary rock
Text derived from https://en.wikipedia.org/w/index.php?oldid=1377499472 under CC BY-SA 4.0; modifications have been made.